Planar PR9020 Remote control, Laser pointer, Putting batteries, Hitachi MAXELL, Part No.LR6

Page 15

Remote control

Remote control

Laser pointer

This remote control has a laser pointer in place of a finger or rod. The laser beam works and the LASER INDICATOR lights while the LASER button is pressed.

LASER INDICATOR

LASER button

WARNING ►The laser pointer of the remote control is used in place of a finger or rod. Never look directly into the laser beam outlet or point the laser beam at other people. The laser beam can cause vision problems.

CAUTION ►Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

Putting batteries

Please load the batteries before using the remote control. If the remote control starts to malfunction, replace the batteries. If you will not use the remote control for an extended period, remove the batteries from the remote control and store them in a safe place.

1. Slide back and remove the battery cover in the direction of the arrow.

2. Align and insert the two AA batteries

(HITACHI MAXELL, Part No.LR6

or R6P) according to their plus and minus terminals as indicated in the remote control.

3. Replace the battery cover in the direction of the arrow and snap it back into place.

WARNING ►Always handle the batteries with care and use them only as directed. Improper use may result in battery explosion, cracking or leakage, which could result in fire, injury and/or pollution of the surrounding environment.

•Be sure to use only the batteries specified. Do not use batteries of different types at the same time. Do not mix a new battery with used one.

•Make sure the plus and minus terminals are correctly aligned when loading a battery.

•Keep a battery away from children and pets.

•Do not recharge, short circuit, solder or disassemble a battery.

•Do not allow a battery in a fire or water. Keep batteries in a dark, cool and dry place.

•If you observe battery leakage, wipe out the leakage and then replace a battery. If the leakage adheres to your body or clothes, rinse well with water immediately.

•Obey the local laws on disposing the battery.

13

Image 15

Contents PR9020 LCD Projector Page About this manual Thank you for purchasing this projectorTrademark acknowledgment Contents Fastening the lens cover Contents of packageHOT Part namesProjector HOTVideo port &10 Control panelRear panel Control port &10 Hdmi port &10Remote control Back Remote controlLaser pointer &13 It is a beam outlet Setting up Suspended from the ceiling ArrangementOn a horizontal SurfaceUsing the security bar and slot Adjusting the projectors elevatorSpeakers wiht an amplifier Connecting your devicesUSB storage SD card Remote control MonitorAbout Plug-and-Play capability Connecting your devicesAC inlet Connector of the power cord To the outlet Connecting power supplyHitachi MAXELL, Part No.LR6 Remote controlLaser pointer Putting batteriesBack sensor About the remote control signalChanging the frequency of remote control signal Front and top sensorsUsing as a simple PC mouse & keyboard Using as a wired remote controlSTANDBY/ON button Power indicator Power switch Power on/offTurning on the power Turning off the powerTemporarily muting the sound Adjusting the volumeSelecting an input signal Operating For an Hdmi signal Searching an input signalSelecting an input signal  For an RGB signal For a video signal and s-video signal Adjusting the zoom and focusAdjusting the lens shift Using the automatic adjustment featureCorrecting the keystone distortions Adjusting the positionFreezing the screen Using the magnify featureTemporarily blanking the screen Enter button Using the menu functionEasy Menu Advanced MenuKeystone Picture ModeAspect AutoEasy Menu Gamma Picture MenuColor Temp Picture MenuSAVE-1, SAVE-2, SAVE-3, SAVE-4 Active IrisLOAD-1, LOAD-2, LOAD-3, LOAD-4 MY MemoryImage Menu Over ScanPosition Size PhaseAuto Adjust Image MenuInput Menu Hdmi Input MenuComponent Video FormatDescription Resolution Setup Menu Setup Menu Audio Menu Or keep no operation for about 10 seconds Using the /// buttons adjusts the menu positionUsing the / buttons switches the mode for the blank screen Screen MenuStart UP Screen MenuCapturing error has occurred. Please try again MyScreenMyScreen registration is finished Message Option Menu Auto SearchAuto on Option Menu Auto OFFLamp Time Service MY ButtonFAN Speed Ghost Filter MessageLens Type Remote Freq Factory ResetKEY Lock Remote ReceivSecurity Using Security FeaturesInputting the Password Changing the PasswordSetting the Password Using the MyScreen Password FunctionDescription If you have forgotten your Password Turning on the MyScreen Password FunctionRegistering the PIN Code Using the PIN Lock FunctionTurning the Password off SecurityDescription Security Turning Off the PIN Lock FunctionIf you have forgotten your PIN Code Using the Transition Detector Function Setting the Transition Detector PasswordTurning On the Transition Detector Function Using the MY Text Password function Setting the Transition Detector offWriting the MY Text Displaying the MY Text Turning on the MY Text PasswordPassword and the screen will return to Network Menu SetupNetwork Menu Projector NameEnter or Input button Use the / buttons To switch the image displayedPress the or ESC button on the remote control Description ShotInformation Part number = MaintenanceCase of replacement by yourself LampLamp Lamp warningAir filter Cleaning the air filterAir filter Remove the battery cover Internal clock batteryCaring for the lens Caring for the cabinet and remote controlOther care Inside of the projectorRelated messages TroubleshootingMessage Description There is no input signal Internal temperature is risingRegarding the indicator lamps Regarding the indicator lamps Signal source does not correctly work Electrical power cord is not pluggedPower switch is not set to the on position Signal cables are not correctly connectedPhenomena that may be easily mistaken for machine defects Whisper function is working Color settings are not correctly adjustedColor Space setting is not suitable Not properly adjustedAir filter 997-5215-00MU03642 Warranty and after-serviceSpecifications Specifications319 418 139 154 Unit mm SpecificationsCorporate Headquarters NW Compton Drive Beaverton, or Planar Systems, Inc