Planar PR9020 user manual Option Menu, Auto OFF, Lamp Time

Page 45

OPTION Menu

OPTION Menu (continued)

Item

Description

 

 

 

Using the ▲/▼ buttons adjusts the time to count down to

 

automatically turn the projector off.

 

Long (max. 99 minutes) ó Short (min. 0 minute = DISABLE)

AUTO OFF

When the time is set to 0, the projector is not turned off automatically.

When the time is set to 1 to 99, and when the passed time with no-

 

signal or an unsuitable signal reaches at the set time, the projector

 

lamp will be turned off.

 

If one of the projector's buttons or the remote control buttons

 

is pressed or one of the commands (except get commands) is

 

transmitted to the control port during the corresponding time,

 

projector will not be turned off.

 

Please refer to the section “Turning off the power” (16).

 

The lamp time is the usage time of the lamp, counted after the last

 

resetting. It is shown in the OPTION menu.

 

Pressing the RESET button on the remote control or the ► button

 

of the projector displays a dialog.

LAMP TIME

To reset the lamp time, select the RESET using the ▲ button.

 

RESET ï CANCEL

 

• Please reset the lamp time only when you have replaced the lamp,

 

for a suitable indication about the lamp.

 

• For the lamp replacement, see the section "Lamp" (60, 61).

 

The filter time is the usage time of the air filter, counted after the last

 

resetting. It is shown in the OPTION menu.

 

Pressing the RESET button on the remote control or the ► button

 

of the projector displays a dialog.

FILTER TIME

To reset the filter time, select the RESET using the ▲ button.

 

RESET ï CANCEL

Please reset the filter time only when you have cleaned or replaced the air filter, for a suitable indication about the air filter.

For the air filter cleaning, see the section "Air filter" (62, 63). (continued on next page)

43

Image 45
Contents PR9020 LCD Projector Page About this manual Thank you for purchasing this projectorTrademark acknowledgment Contents Fastening the lens cover Contents of packageProjector Part namesHOT HOTRear panel Control panelControl port &10 Hdmi port &10 Video port &10Remote control Back Remote controlLaser pointer &13 It is a beam outlet Setting up On a horizontal ArrangementSurface Suspended from the ceilingUsing the security bar and slot Adjusting the projectors elevatorUSB storage SD card Remote control Connecting your devicesMonitor Speakers wiht an amplifierAbout Plug-and-Play capability Connecting your devicesAC inlet Connector of the power cord To the outlet Connecting power supplyLaser pointer Remote controlPutting batteries Hitachi MAXELL, Part No.LR6Changing the frequency of remote control signal About the remote control signalFront and top sensors Back sensorUsing as a simple PC mouse & keyboard Using as a wired remote controlTurning on the power Power on/offTurning off the power STANDBY/ON button Power indicator Power switchSelecting an input signal Adjusting the volumeOperating Temporarily muting the soundSelecting an input signal Searching an input signal For an RGB signal  For an Hdmi signalAdjusting the lens shift Adjusting the zoom and focusUsing the automatic adjustment feature  For a video signal and s-video signalCorrecting the keystone distortions Adjusting the positionFreezing the screen Using the magnify featureTemporarily blanking the screen Easy Menu Using the menu functionAdvanced Menu Enter buttonAspect Picture ModeAuto KeystoneEasy Menu Gamma Picture MenuColor Temp Picture MenuLOAD-1, LOAD-2, LOAD-3, LOAD-4 Active IrisMY Memory SAVE-1, SAVE-2, SAVE-3, SAVE-4Image Menu Over ScanPosition Auto Adjust PhaseImage Menu SizeInput Menu Component Input MenuVideo Format HdmiDescription Resolution Setup Menu Setup Menu Audio Menu Using the / buttons switches the mode for the blank screen Using the /// buttons adjusts the menu positionScreen Menu Or keep no operation for about 10 secondsStart UP Screen MenuCapturing error has occurred. Please try again MyScreenMyScreen registration is finished Message Option Menu Auto SearchAuto on Option Menu Auto OFFLamp Time Service MY ButtonFAN Speed Ghost Filter MessageLens Type KEY Lock Factory ResetRemote Receiv Remote FreqInputting the Password Using Security FeaturesChanging the Password SecurityDescription If you have forgotten your Password Using the MyScreen Password FunctionTurning on the MyScreen Password Function Setting the PasswordTurning the Password off Using the PIN Lock FunctionSecurity Registering the PIN CodeDescription Security Turning Off the PIN Lock FunctionIf you have forgotten your PIN Code Using the Transition Detector Function Setting the Transition Detector PasswordTurning On the Transition Detector Function Using the MY Text Password function Setting the Transition Detector offWriting the MY Text Displaying the MY Text Turning on the MY Text PasswordPassword and the screen will return to Network Menu SetupNetwork Menu Projector NameEnter or Input button Press the or ESC button on the remote control To switch the image displayedDescription Shot Use the / buttonsInformation Case of replacement by yourself MaintenanceLamp Part number =Lamp Lamp warningAir filter Cleaning the air filterAir filter Remove the battery cover Internal clock batteryOther care Caring for the cabinet and remote controlInside of the projector Caring for the lensMessage Description There is no input signal TroubleshootingInternal temperature is rising Related messagesRegarding the indicator lamps Regarding the indicator lamps Power switch is not set to the on position Electrical power cord is not pluggedSignal cables are not correctly connected Signal source does not correctly workPhenomena that may be easily mistaken for machine defects Color Space setting is not suitable Color settings are not correctly adjustedNot properly adjusted Whisper function is workingSpecifications Warranty and after-serviceSpecifications Air filter 997-5215-00MU03642319 418 139 154 Unit mm SpecificationsCorporate Headquarters NW Compton Drive Beaverton, or Planar Systems, Inc