Planar PR9020 user manual Regarding the indicator lamps

Page 70

Troubleshooting

Regarding the indicator lamps (continued)

POWER

LAMP

TEMP

Description

indicator

indicator

indicator

 

 

 

 

 

 

 

 

The cooling fan is not operating.

Blinking

 

 

Please turn the power off, and allow the projector to

 

 

cool down at least 20 minutes. After the projector has

In Red

 

 

Turned

Blinking

sufficiently cooled down, please make confirmation

or

off

In Red

that no foreign matter has become caught in the fan,

Lighting

 

 

etc., and then turn the power on again.

In Red

 

 

 

 

If the same indication is displayed after the remedy,

 

 

 

 

 

 

please contact your dealer or service company.

 

 

 

There is a possibility that the interior portion

 

 

 

has become heated.

 

 

 

Please turn the power off, and allow the projector to

Blinking

 

 

cool down at least 20 minutes. After the projector has

 

 

sufficiently cooled down, please make confirmation of

In Red

 

 

Turned

Lighting

the following items, and then turn the power on again.

or

off

In Red

• Is there blockage of the air passage aperture?

Lighting

 

 

• Is the air filter dirty?

In Red

 

 

 

 

• Does the peripheral temperature exceed 35°C?

 

 

 

 

 

 

If the same indication is displayed after the remedy,

 

 

 

please set FAN SPEED of the SERVICE item in the

 

 

 

OPTION menu to HIGH.

 

 

 

It is time to clean the air filter.

 

 

 

Please immediately turn the power off, and clean or

Lighting

Simultaneous

change the air filter referring to the section “Air Filter”.

In Green

blinking in Red

After cleaning or changing the air filter, please be sure

 

 

 

to reset the filter timer. After the remedy, reset the

 

 

 

power to ON.

 

 

 

There is a possibility that the interior portion

Lighting

Alternative

has become overcooled.

Please use the unit within the usage temperature

In Green

blinking in Red

parameters (5°C to 35°C). After the treatment, reset

 

 

 

 

 

 

the power to ON.

Blinking in

 

 

At least 1 “Power ON” schedule is saved to the

Green for

Turned

Turned

projector.

approx. 3

off

off

(Please refer to the User’s Manual-Network Guide:

seconds

 

 

Schedule Settings for more information.)

NOTE • When the interior portion has become overheated, for safety purposes, the power source is automatically turned off, and the indicator lamps may also be turned off. In such a case, press the “” (OFF) side of the power switch, and wait at least 45 minutes. After the projector has sufficiently cooled down, please make confirmation of the attachment state of the lamp and lamp cover, and then turn the power on again.

68

Page 69 Page 71
Image 70
Page 69 Page 71
Contents PR9020 LCD Projector Page Thank you for purchasing this projector About this manualTrademark acknowledgment Contents Contents of package Fastening the lens coverHOT Part namesProjector HOTControl port &10 Hdmi port &10 Control panelRear panel Video port &10Back Remote control Remote controlLaser pointer &13 It is a beam outlet Setting up Surface ArrangementOn a horizontal Suspended from the ceilingAdjusting the projectors elevator Using the security bar and slotMonitor Connecting your devicesUSB storage SD card Remote control Speakers wiht an amplifierConnecting your devices About Plug-and-Play capabilityConnecting power supply AC inlet Connector of the power cord To the outletPutting batteries Remote controlLaser pointer Hitachi MAXELL, Part No.LR6Front and top sensors About the remote control signalChanging the frequency of remote control signal Back sensorUsing as a wired remote control Using as a simple PC mouse & keyboardTurning off the power Power on/offTurning on the power STANDBY/ON button Power indicator Power switchOperating Adjusting the volumeSelecting an input signal Temporarily muting the sound For an RGB signal Searching an input signalSelecting an input signal  For an Hdmi signalUsing the automatic adjustment feature Adjusting the zoom and focusAdjusting the lens shift  For a video signal and s-video signalAdjusting the position Correcting the keystone distortionsUsing the magnify feature Freezing the screenTemporarily blanking the screen Advanced Menu Using the menu functionEasy Menu Enter buttonAuto Picture ModeAspect KeystoneEasy Menu Picture Menu GammaPicture Menu Color TempMY Memory Active IrisLOAD-1, LOAD-2, LOAD-3, LOAD-4 SAVE-1, SAVE-2, SAVE-3, SAVE-4Over Scan Image MenuPosition Image Menu PhaseAuto Adjust SizeInput Menu Video Format Input MenuComponent HdmiDescription Resolution Setup Menu Setup Menu Audio Menu Screen Menu Using the /// buttons adjusts the menu positionUsing the / buttons switches the mode for the blank screen Or keep no operation for about 10 secondsScreen Menu Start UPMyScreen Capturing error has occurred. Please try againMyScreen registration is finished Message Auto Search Option MenuAuto on Auto OFF Option MenuLamp Time MY Button ServiceFAN Speed Filter Message GhostLens Type Remote Receiv Factory ResetKEY Lock Remote FreqChanging the Password Using Security FeaturesInputting the Password SecurityTurning on the MyScreen Password Function Using the MyScreen Password FunctionDescription If you have forgotten your Password Setting the PasswordSecurity Using the PIN Lock FunctionTurning the Password off Registering the PIN CodeTurning Off the PIN Lock Function Description SecurityIf you have forgotten your PIN Code Setting the Transition Detector Password Using the Transition Detector FunctionTurning On the Transition Detector Function Setting the Transition Detector off Using the MY Text Password functionWriting the MY Text Turning on the MY Text Password Displaying the MY TextPassword and the screen will return to Setup Network MenuNetwork Menu Name ProjectorEnter or Input button Description Shot To switch the image displayedPress the or ESC button on the remote control Use the / buttonsInformation Lamp MaintenanceCase of replacement by yourself Part number =Lamp warning LampCleaning the air filter Air filterAir filter Internal clock battery Remove the battery coverInside of the projector Caring for the cabinet and remote controlOther care Caring for the lensInternal temperature is rising TroubleshootingMessage Description There is no input signal Related messagesRegarding the indicator lamps Regarding the indicator lamps Signal cables are not correctly connected Electrical power cord is not pluggedPower switch is not set to the on position Signal source does not correctly workPhenomena that may be easily mistaken for machine defects Not properly adjusted Color settings are not correctly adjustedColor Space setting is not suitable Whisper function is workingSpecifications Warranty and after-serviceSpecifications Air filter 997-5215-00MU03642Specifications 319 418 139 154 Unit mmPlanar Systems, Inc Corporate Headquarters NW Compton Drive Beaverton, or
Top Page Image Contents