Onkyo 29400095 instruction manual AV Recording, Recording Separate AV Sources

Page 58

Recording

This section explains how to record the selected input source to a component with recording capability, and how to record audio and video from different sources.

Notes:

The surround sound and DSP listening modes cannot be recorded.

Copy-protected DVDs cannot be recorded.

Only analog inputs can be recorded.

DTS signals will be recorded as noise, so don’t attempt analog recording of DTS CDs or LDs.

AV Recording

Audio sources can be recorded to a recorder (e.g., cas- sette deck, CDR, MD) connected to the TV/TAPE OUT jack. Video sources can be recorded to a video recorder (e.g., VCR, DVD recorder) connected to the VCR/DVR OUT jack. See page 29 or 34 for hookup information.

Recording Separate AV Sources

Here you can record audio and video from completely separate sources, allowing you to overdub audio onto your video recordings. This function takes advantage of the fact that when an audio-only input source (i.e., TV/ TAPE, CD) is selected, the video input source remains unchanged.

In the following example, audio from the CD player con- nected to the CD IN, and video from the camcorder con- nected to the AUX INPUT VIDEO jack are recorded by the VCR connected to the VCR/DVR OUT jacks.

Camcorder

1

2

3

Use the input selector buttons to select the source that you want to record.

You can watch the source while record- ing. The AV receiver’s MASTER VOL- UME control has no effect on recording.

On your recorder, start record- ing.

On the source component, start playback.

If you select another input source dur- ing recording, that input source will be recorded.

video signal audio signal

CD playerVCR

1

Prepare the camcorder and CD player for

 

playback.

 

 

2

Prepare the VCR for recording.

 

 

3

Press the [AUX] input selector button.

 

 

4

Press the [CD] input selector button.

 

This selects the CD player as the audio source, but

 

leaves the camcorder as the video source.

 

 

5

Start recording on the VCR and start play-

 

back on the camcorder and CD player.

The video from the camcorder and the audio from the CD player are recorded by the VCR.

58

Image 58
Contents HT-RC160 Important Safety Instructions AvisPreventing Hearing Loss Caution PrecautionsPower Batteries and Heat Exposure WarningMake sure you have the following accessories Supplied AccessoriesSpeaker cable labels Contents Processing FeaturesAmplifier ConnectionsZone 2 Room Multiroom CapabilityMain Room Front high left and right speakersFront & Rear Panels Front PanelFront & Rear Panels DisplayRear Panel CBL/SAT TV/TAPE IN/OUTGame VCR/DVR IN/OUTInstalling the Batteries Remote ControllerAiming the Remote Controller Remote Controller Controlling the AV ReceiverFront left and right speakers About Home TheaterEnjoying Home Theater Center speakerSpeaker Configuration Connecting the AV ReceiverConnecting Your Speakers Using Dipole SpeakersSpeaker Connection Precautions Connecting the AV ReceiverConnecting a Powered Subwoofer Connecting the Speaker CablesFront high Bi-amping the Front Speakers Bi-amping Speaker HookupConnecting the AM Loop Antenna Connecting AntennaConnecting the Indoor FM Antenna Attach the FM antenna, as shownConnecting an Outdoor AM Antenna Connecting an Outdoor FM AntennaUsing a TV/FM Antenna Splitter Optical Digital Jacks AV Connection Color Coding About AV ConnectionsAV Cables & Jacks Supported Audio Formats Connecting Components with HdmiAbout Hdmi About Copyright ProtectionMaking Hdmi Connections Video SignalsAudio Signals StepWhich Connections Should I Use? Connecting Both Audio & VideoVideo Connection Formats DVD/BD player, etc Audio Signal Flow Chart Signal SelectionSignal Selection Example Audio Connection FormatsAudio Connection Connecting a TV or ProjectorVideo Connection TV, projector EtcConnecting a DVD/BD Player DVD/BD playerConnecting a VCR or DVD/BD Recorder for Playback DVD/BD recorderMake the audio connection a Connecting a VCR or DVD/BD Recorder for RecordingRecorder Digital in Optical 2 CD Satellite, cable, set-top box, etcConnecting a Game Console Game ConsoleMake the connection a Connecting a Camcorder or Other DeviceConnecting a Portable Audio player Make the audio connection aAn MC head amp and phono preamp are necessary to Connecting a CD Player or TurntableCD Player or Turntable MM with Built-in Phono Preamp Step Phono preamp is necessary to connect a turntable thatConnecting a Cassette, CDR, MiniDisc, or DAT Recorder If Your iPod Supports Video Connecting an RI DockConnecting a Dock with the Universal Port connector If Your iPod Doesn’t Support VideoAuto Power On/Standby Connecting Onkyo u ComponentsConnecting the Power Cord Make the uconnection see illustration belowSmooth Operation in a Few Easy Steps Turning On the AV ReceiverTurning On and Standby Have you connected an Onkyo RI Dock?Using the Onscreen Setup Menus First Time SetupUsing the Display to change the settings Onscreen Setup Menus and DisplayVideo Input Setup First Time SetupHdmi Input Setup Video Input, and then press Component Video SetupTons to select 2. Component Then use the Left and Right e/r buttons to selectTons to select 3. Digital Audio Digital Input SetupInput, and then press Enter Press the Receiver button Followed by the Setup button Speaker SettingsPowered Zone Tons to select 1. Speaker SetTons to select 2. Tuner, FM/AM Frequency Step SetupPress the Receiver button Use the Left and Right e/r Buttons to select 200kHz/10kHzChanging the Input Display First measurement point Audyssey 2EQ Room Correction and Speaker SetupMeasurement Positions Second measurement pointTurn on the AV receiver Using Audyssey 2EQWhen you’ve finished, press the Enter button Connected TVFollowing screen appears CancelPress Enter SaveSpeaker Detect Error Error MessagesDisconnect the speaker setup MicrophoneSpeaker matching error Changing the Speaker Settings ManuallyUsing a Powered Subwoofer Writing ErrorBasic Operations Select a listening mode and enjoySee Using the Listening Modes on Selecting the Input SourceBasic Operations Adjusting the Bass & TrebleSetting the Display Brightness Displaying Source InformationMuting the AV receiver Using the Sleep TimerUsing Headphones You can temporarily mute the output of the AV receiverListening to the Radio Using the TunerTuning into Radio Stations Listening to the RadioDeleting Presets Presetting AM/FM StationsSelecting Presets Listening to the RadioCompatible iPod models UP-A1 series Dock for iPodAbout the UP-A1 series Dock Putting Your iPod in the DockUP-A1 series Dock for iPod Using Your iPod models Alarm ClockCharging Your iPod models Battery Controlling iPodStatus messages AV Recording RecordingRecording Separate AV Sources Selecting Listening Modes Using the Listening ModesSelecting with the Remote Controller Selecting on the AV receiverMono/Multiplex Sources Using the Listening ModesListening Modes Available for Each Source Format Available Listening ModesStereo Source PLIIx Movie Channel SourcesDirect Stereo Mono DolbyDigital Plus/TrueHD Multichannel PLIIx MusicDirect Resolution Audio/DTS-HD Master Audio PLIIz HeightDTS-ES Discrete/Matrix Sources Discrete DTS-ES MatrixAbout the Listening Modes Onkyo Original DSP Modes Main menu Submenus Advanced SetupOnscreen Setup Menus PagesCommon Procedures in Setup Menu Advanced SetupSpeaker Setup Speaker Distance LPF of LFEDouble Bass*9 Unit FeetPress the Down w button to select Channel, and then use Equalizer SettingsLevel calibration Left and Right e/ r buttons to select a speakerDolby Settings PLIIx Music 2ch Input Audio AdjustMultiplex/Mono Settings Dolby EXAudyssey Settings DTS Setting Neo6 MusicTheater-Dimensional Setting Using the Audio Settings Music Optimizer Audyssey Dynamic VolumeCinemaFILTER Speaker LayoutWhen you’ve finished, press the Setup button Listening Mode Preset menu appearsSignal format selection menu appears Assigning Listening Modes to Input SourcesIntelliVolume Source SetupSync Name Edit To correct a characterVolume Setup Miscellaneous Volume/OSD SetupOSD Setup Remote ID Hardware SetupTuner Hdmi Control Rihd Power ControlColor Disconnect → Rihd OffLock Setup Using the Video SettingsDigital Input Signal Formats Connecting Your Zone 2 Speakers to an Amp in Zone Connecting ZoneConnecting Your Zone 2 Speakers Directly to the AV receiver ZoneUse the Up and Down q/ w Setting the Powered ZoneButtons to select Powered Zone 2, and use the Left Right e/r buttons to selectControlling Zone 2 with the Remote Controller Using ZoneControlling Zone 2 from the AV receiver Zone 2 button, and then Adjusting the Volume for ZoneMuting Zones Use the VOL q/ w buttonController Setup, and then Preprogrammed Remote Control CodesLooking up for Remote Control Code Controlling Other ComponentsIf you can control component Remote Mode Setup menuControlling Other Components Buttons to select Works,Entering Remote Control Codes Resetting Remote Mode Buttons Remote Control Codes for Onkyo Components Connected via uResetting the Remote Controller Controlling a TV Controlling a DVD/BD Player, or DVD/BD Recorder Controlling a VCR or PVR Play Mode buttonPlayback button Controlling a Satellite Receiver or Cable Receiver Controlling a CD Player Disc +/- buttonControlling an RI Dock When Using an RI DockWorks as a Mode button when used with a DS-A2 RI Dock Turns on the backlight for 30 secondsRewind and Fast Forward 5/4 buttons Controlling a Cassette RecorderPrevious and Next 7/6 buttons Reverse Play t buttonTroubleshooting Troubleshooting There’s no picture from a source connected to an Hdmi Remote Controller Remote controller doesn’t workAV receiver’s remote controller doesn’t control your iPod Onscreen menus don’t appearZone There’s no sound Others Sound changes when I connect my headphonesRecording Can’t record How do I change the language of a multiplex sourceVideo Section SpecificationsAmplifier Section Tuner SectionVideo Resolution Chart Memo 103Onkyo Europe Electronics GmbH Onkyo Europe UK Office