Onkyo 29400095 instruction manual Using Zone, Controlling Zone 2 from the AV receiver

Page 84

Zone 2—Continued

Using Zone 2

This section explains how to turn Zone 2 on and off, how to select an input source for Zone 2, and how to adjust the volume for Zone 2.

Controlling Zone 2 from the AV receiver

ZONE 2

OFF

INPUT SELECTOR

1

To turn on Zone 2 and select an

 

 

input source, press the [ZONE 2]

 

button followed by an input

 

selector button within 8 seconds.

 

Zone 2 turns on, the ZONE 2 indicator

 

lights up.

 

To select AM or FM press the

 

[TUNER] input selector button repeat-

 

edly.

 

To select the same source as that of the

 

main room, press the [ZONE 2] button

 

repeatedly until “Z2 Selector: Source”

 

appears on the display.

 

Note:

 

You cannot select different AM or FM

 

radio stations for your main room and

 

Zone 2. The same AM/FM radio station

2

will be heard in each room.

To turn off Zone 2, press the

 

 

[OFF] button.

Controlling Zone 2 with the Remote Controller

ON/

ZONE2

STANDBY

INPUT

SELECTOR

Note:

To control Zone 2, you must press the remote control- ler’s [ZONE 2] button first.

1

Press the [ZONE 2] button, then

 

 

point the remote controller at the

 

AV receiver and press the [ON/

 

STANDBY] button.

 

Zone 2 turns on, the ZONE 2 indicator

 

lights up.

2

To select an input source for

 

 

Zone 2, press the [ZONE 2]

 

button, followed by an INPUT

 

SELECTOR button.

To select AM or FM press the [TUNER] INPUT SELECTOR button repeatedly.

Note:

You cannot select different AM or FM radio stations for your main room and Zone 2. The same AM/FM radio station will be heard in each room.

3

To turn off Zone 2, press the

 

 

[ZONE 2] button, followed by the

 

[ON/STANDBY] button.

84

Image 84
Contents HT-RC160 Important Safety Instructions AvisPrecautions PowerPreventing Hearing Loss Caution Batteries and Heat Exposure WarningSupplied Accessories Make sure you have the following accessoriesSpeaker cable labels Contents Features AmplifierProcessing ConnectionsMultiroom Capability Main RoomZone 2 Room Front high left and right speakersFront & Rear Panels Front PanelFront & Rear Panels DisplayRear Panel TV/TAPE IN/OUT GameCBL/SAT VCR/DVR IN/OUTRemote Controller Installing the BatteriesAiming the Remote Controller Remote Controller Controlling the AV ReceiverAbout Home Theater Enjoying Home TheaterFront left and right speakers Center speakerConnecting the AV Receiver Connecting Your SpeakersSpeaker Configuration Using Dipole SpeakersConnecting the AV Receiver Connecting a Powered SubwooferSpeaker Connection Precautions Connecting the Speaker CablesFront high Bi-amping the Front Speakers Bi-amping Speaker HookupConnecting Antenna Connecting the Indoor FM AntennaConnecting the AM Loop Antenna Attach the FM antenna, as shownConnecting an Outdoor FM Antenna Connecting an Outdoor AM AntennaUsing a TV/FM Antenna Splitter About AV Connections Optical Digital Jacks AV Connection Color CodingAV Cables & Jacks Connecting Components with Hdmi About HdmiSupported Audio Formats About Copyright ProtectionVideo Signals Audio SignalsMaking Hdmi Connections StepConnecting Both Audio & Video Which Connections Should I Use?Video Connection Formats Signal Selection Signal Selection ExampleDVD/BD player, etc Audio Signal Flow Chart Audio Connection FormatsConnecting a TV or Projector Video ConnectionAudio Connection TV, projector EtcConnecting a DVD/BD Player DVD/BD playerConnecting a VCR or DVD/BD Recorder for Playback DVD/BD recorderConnecting a VCR or DVD/BD Recorder for Recording Make the audio connection aRecorder Digital in Optical 2 CD Satellite, cable, set-top box, etcConnecting a Game Console Game ConsoleConnecting a Camcorder or Other Device Connecting a Portable Audio playerMake the connection a Make the audio connection aConnecting a CD Player or Turntable CD Player or Turntable MM with Built-in Phono Preamp StepAn MC head amp and phono preamp are necessary to Phono preamp is necessary to connect a turntable thatConnecting a Cassette, CDR, MiniDisc, or DAT Recorder Connecting an RI Dock Connecting a Dock with the Universal Port connectorIf Your iPod Supports Video If Your iPod Doesn’t Support VideoConnecting Onkyo u Components Connecting the Power CordAuto Power On/Standby Make the uconnection see illustration belowTurning On the AV Receiver Turning On and StandbySmooth Operation in a Few Easy Steps Have you connected an Onkyo RI Dock?First Time Setup Using the Display to change the settingsUsing the Onscreen Setup Menus Onscreen Setup Menus and DisplayFirst Time Setup Video Input SetupHdmi Input Setup Component Video Setup Tons to select 2. ComponentVideo Input, and then press Then use the Left and Right e/r buttons to selectDigital Input Setup Tons to select 3. Digital AudioInput, and then press Enter Speaker Settings Powered ZonePress the Receiver button Followed by the Setup button Tons to select 1. Speaker SetFM/AM Frequency Step Setup Press the Receiver buttonTons to select 2. Tuner, Use the Left and Right e/r Buttons to select 200kHz/10kHzChanging the Input Display Audyssey 2EQ Room Correction and Speaker Setup Measurement PositionsFirst measurement point Second measurement pointUsing Audyssey 2EQ When you’ve finished, press the Enter buttonTurn on the AV receiver Connected TVCancel Press EnterFollowing screen appears SaveError Messages Disconnect the speaker setupSpeaker Detect Error MicrophoneChanging the Speaker Settings Manually Using a Powered SubwooferSpeaker matching error Writing ErrorSelect a listening mode and enjoy See Using the Listening Modes onBasic Operations Selecting the Input SourceAdjusting the Bass & Treble Setting the Display BrightnessBasic Operations Displaying Source InformationUsing the Sleep Timer Using HeadphonesMuting the AV receiver You can temporarily mute the output of the AV receiverUsing the Tuner Tuning into Radio StationsListening to the Radio Listening to the RadioPresetting AM/FM Stations Selecting PresetsDeleting Presets Listening to the RadioUP-A1 series Dock for iPod About the UP-A1 series DockCompatible iPod models Putting Your iPod in the DockUsing Your iPod models Alarm Clock Charging Your iPod models BatteryUP-A1 series Dock for iPod Controlling iPodStatus messages Recording AV RecordingRecording Separate AV Sources Using the Listening Modes Selecting with the Remote ControllerSelecting Listening Modes Selecting on the AV receiverUsing the Listening Modes Listening Modes Available for Each Source FormatMono/Multiplex Sources Available Listening ModesStereo Source Channel Sources Direct Stereo Mono DolbyDigital Plus/TrueHD MultichannelPLIIx Movie PLIIx MusicResolution Audio/DTS-HD Master Audio PLIIz Height DTS-ES Discrete/Matrix SourcesDirect Discrete DTS-ES MatrixAbout the Listening Modes Onkyo Original DSP Modes Advanced Setup Onscreen Setup MenusMain menu Submenus PagesAdvanced Setup Common Procedures in Setup MenuSpeaker Setup LPF of LFE Double Bass*9Speaker Distance Unit FeetEqualizer Settings Level calibrationPress the Down w button to select Channel, and then use Left and Right e/ r buttons to select a speakerAudio Adjust Multiplex/Mono SettingsDolby Settings PLIIx Music 2ch Input Dolby EXDTS Setting Neo6 Music Audyssey SettingsTheater-Dimensional Setting Using the Audio Settings Audyssey Dynamic Volume CinemaFILTERMusic Optimizer Speaker LayoutListening Mode Preset menu appears Signal format selection menu appearsWhen you’ve finished, press the Setup button Assigning Listening Modes to Input SourcesSource Setup IntelliVolumeSync Name Edit To correct a characterMiscellaneous Volume/OSD Setup Volume SetupOSD Setup Hardware Setup Remote IDTuner Power Control ColorHdmi Control Rihd Disconnect → Rihd OffLock Setup Using the Video SettingsDigital Input Signal Formats Connecting Zone Connecting Your Zone 2 Speakers Directly to the AV receiverConnecting Your Zone 2 Speakers to an Amp in Zone ZoneSetting the Powered Zone Buttons to select PoweredUse the Up and Down q/ w Zone 2, and use the Left Right e/r buttons to selectUsing Zone Controlling Zone 2 with the Remote ControllerControlling Zone 2 from the AV receiver Adjusting the Volume for Zone Muting ZonesZone 2 button, and then Use the VOL q/ w buttonPreprogrammed Remote Control Codes Looking up for Remote Control CodeController Setup, and then Controlling Other ComponentsRemote Mode Setup menu Controlling Other ComponentsIf you can control component Buttons to select Works,Entering Remote Control Codes Remote Control Codes for Onkyo Components Connected via u Resetting Remote Mode ButtonsResetting the Remote Controller Controlling a TV Controlling a DVD/BD Player, or DVD/BD Recorder Play Mode button Controlling a VCR or PVRPlayback button Controlling a Satellite Receiver or Cable Receiver Controlling a CD Player Disc +/- buttonWhen Using an RI Dock Works as a Mode button when used with a DS-A2 RI DockControlling an RI Dock Turns on the backlight for 30 secondsControlling a Cassette Recorder Previous and Next 7/6 buttonsRewind and Fast Forward 5/4 buttons Reverse Play t buttonTroubleshooting Troubleshooting Remote Controller Remote controller doesn’t work AV receiver’s remote controller doesn’t control your iPodThere’s no picture from a source connected to an Hdmi Onscreen menus don’t appearOthers Sound changes when I connect my headphones Recording Can’t recordZone There’s no sound How do I change the language of a multiplex sourceSpecifications Amplifier SectionVideo Section Tuner SectionVideo Resolution Chart Memo 103Onkyo Europe Electronics GmbH Onkyo Europe UK Office