Microsoft IBUS-BAT-1370 Hardware Installation Floppy Disk Controller, IDE Hard Disk Interface

Page 21

Hardware Installation

2.7.4 Floppy Disk Controller

The system board is equipped with a shrouded floppy disk header that supports two standard floppy disk drives. To prevent improper floppy cable installation, the shrouded floppy disk header has a keying mechanism. The 34-pin connector on the floppy cable can be placed into the header only if pin 1 of the connector is aligned with pin 1 of the header. You may enable or disable this function in the Integrated Peripherals setup of the Award BIOS.

Connecting the Floppy Disk Cable

1.Install the 34-pin header connector into the shrouded floppy disk

header (J10) on the system board. The colored edge of the ribbon should be aligned with pin 1 of J10.

2. Install the other 34-pin header connector(s) into

the disk drive(s). Align the colored edge of the daisy

chained ribbon cable with pin 1 of the drive edge connector(s). The end-most connector should be attached to the drive you want to designate as Drive A.

2.7.5 IDE Hard Disk Interface

The system board is equipped with two shrouded PCI IDE headers that will interface four Enhanced IDE (Integrated Drive Electronics) hard disk drives. To prevent improper IDE cable installation, each shrouded PCI IDE header has a keying mechanism. The 40-pin connector on the IDE cable can be placed into the header only if pin 1 of the connector is aligned with pin 1 of the header.

21

Image 21

Contents 37610914 IBUS-BAT-I370Trademarks CopyrightCE, FCC and DOC Statement Table of Contents Appendix B Troubleshooting Appendix a System Error MessagesFeatures Features and SpecificationsChipset ProcessorIntroduction ConnectorsExpansion Slots Desktop Management Interface DMIPCI Bus Master IDE Controller IrDA InterfaceUSB Ports Introduction Intelligence Virus Protection Acpi ATX power supply onlyPackage Checklist System Board Layout HardwareInstallationHardware Installation Installing the DIM ModuleSystem Memory DIP Switch Settings for Processors For Factory Use Only Hardware Installation Jumper Settings for the CPU’s Front Side BusJumper Settings for Clearing Cmos Data On Disable Serial Ports Connecting the Serial PortsHardware Installation 2 PS/2 Mouse Port Connecting the Parallel Printer Port Hardware Installation Parallel PortHardware Installation Floppy Disk Controller Connecting the Floppy Disk CableIDE Hard Disk Interface Adding a Second IDE Hard Drive Connecting the Hard Disk CableConnecting the USB Ports Hardware Installation USB PortsHardware Installation IrDA Connector Chassis Fan Connector Hardware Installation CPU Fan ConnectorSB-LINK Connector Hardware Installation AGP Fan ConnectorWOL COM PW-OK 5VSB Hardware Installation Power ConnectorHardware Installation 14 J9 LEDs and Switches Keylock Power/Standby LED and Keylock Connector Basic Input/Output System Standard Cmos SetupAward Bios Setup Utility DateTime Drive a and Drive B VideoHalt On Virus Warning Award Bios Setup Utility Bios Features SetupBoot Sequence Quick Power On Self TestBoot Up Floppy Seek CPU L1 Cache and CPU L2 CacheTypematic Rate Setting Boot Up NumLock StatusTypematic Delay Msec Typematic Rate Chars/SecHDD S.M.A.R.T. Capability OS Select for Dram 64MBAward Bios Setup Utility 3.1.3 Chipset Features Setup Sdram RAS-to-CAS DelaySdram RAS Precharge Time System Bios Cacheable Dram Data Integrity ModeVideo Bios Cacheable Bit I/O Recovery Time and 16 Bit I/O Recovery TimePCI 2.1 Compliance Memory Hole At 15M-16MAGP Aperture Size MB CPU/PCI Clock MHzSpread Spectrum Power Management SetupAcpi Function Power ManagementPM Control by APM Video Off MethodSuspend Mode Standby ModeHDD Power Down Video Off AfterSoft-Off by PWR-BTTN PWR Lost Resume StateResume On Ring Timer hhmmss Resume On AlarmResume On LAN Date of Month5 PNP/PCI Configuration Reset Configuration DataResources Controlled By Assign IRQ for VGA Load Fail-Safe SettingsAssign IRQ for USB PCI Slot 1 Use IRQ to PCI Slot 4 Use IRQAward Bios Setup Utility Load Optimal Settings IDE HDD Block ModeIntegrated Peripherals USB Keyboard Support On-Chip Primary PCI IDE and On-Chip Secondary PCI IDEInit Display First KBC Input ClockIR Transmission Delay UART2 Mode SelectOnboard FDC Controller Onboard Serial Port 1 and Onboard Serial PortKeyboard/Mouse Power On Parallel Port Mode, ECP Mode Use DMA and EPP Mode SelectSupervisor Password IDE HDD Auto Detection Award Bios Setup Utility User PasswordExit Without Saving Award Bios Setup Utility Save & Exit SetupRunning the DMI Utility Desktop Management Interface DMIEdit DMI Supported Softwares Using the DMI UtilitySupported Softwares Add DMI Load DMI FileSave DMI File Supported Softwares Patch Utility for WindowsPost Beep Error MessagesSystem Error Message Monitor/Display Troubleshooting ChecklistTroubleshooting Power SupplyFloppy Drive Hard disk failure Troubleshooting Hard DriveTroubleshooting Serial Port KeyboardSystem Board