Microsoft System Board, IBUS-BAT-1370 manual Troubleshooting, Power Supply, Floppy Drive

Page 62

*Troubleshooting

The picture seems to be constantly moving.

1.The monitor has lost its vertical sync. Adjust the monitor’s vertical sync.

2.Move away any objects, such as another monitor or fan, that may be creating a magnetic field around the display.

3.Make sure your video card’s output frequencies are supported by this monitor.

The screen seems to be constantly wavering.

1.If the monitor is close to another monitor, the adjacent monitor may need to be turned off. Fluorescent lights adjacent to the monitor may also cause screen wavering.

Power Supply

When the computer is turned on, nothing happens.

1.Check that one end of the AC power cord is plugged into a live outlet and the other end properly plugged into the back of the system.

2.Make sure that the voltage selection switch on the back panel is set for the correct type of voltage you are using.

3.The power cord may have a “short” or “open”. Inspect the cord and install a new one if necessary.

Floppy Drive

The computer cannot access the floppy drive.

1.The floppy diskette may not be formatted. Format the diskette and try again.

2.The diskette may be write-protected. Use a diskette that is not write-protected.

3.You may be writing to the wrong drive. Check the path statement to make sure you are writing to the targeted drive.

4.There is not enough space left on the diskette. Use another diskette with adequate storage space.

62

Image 62
Contents IBUS-BAT-I370 37610914Copyright TrademarksCE, FCC and DOC Statement Table of Contents Appendix a System Error Messages Appendix B TroubleshootingChipset Features and SpecificationsFeatures ProcessorExpansion Slots ConnectorsIntroduction Desktop Management Interface DMIUSB Ports PCI Bus Master IDE ControllerIrDA Interface Introduction Intelligence Acpi ATX power supply only Virus ProtectionPackage Checklist HardwareInstallation System Board LayoutSystem Memory Hardware InstallationInstalling the DIM Module DIP Switch Settings for Processors For Factory Use Only Jumper Settings for the CPU’s Front Side Bus Hardware InstallationJumper Settings for Clearing Cmos Data On Disable Connecting the Serial Ports Serial PortsHardware Installation 2 PS/2 Mouse Port Hardware Installation Parallel Port Connecting the Parallel Printer PortIDE Hard Disk Interface Hardware Installation Floppy Disk ControllerConnecting the Floppy Disk Cable Connecting the Hard Disk Cable Adding a Second IDE Hard DriveHardware Installation USB Ports Connecting the USB PortsHardware Installation IrDA Connector Hardware Installation CPU Fan Connector Chassis Fan ConnectorHardware Installation AGP Fan Connector SB-LINK ConnectorWOL Hardware Installation Power Connector COM PW-OK 5VSBHardware Installation 14 J9 LEDs and Switches Keylock Power/Standby LED and Keylock Connector Standard Cmos Setup Basic Input/Output SystemTime Award Bios Setup UtilityDate Halt On Drive a and Drive BVideo Award Bios Setup Utility Bios Features Setup Virus WarningBoot Up Floppy Seek Quick Power On Self TestBoot Sequence CPU L1 Cache and CPU L2 CacheTypematic Delay Msec Boot Up NumLock StatusTypematic Rate Setting Typematic Rate Chars/SecOS Select for Dram 64MB HDD S.M.A.R.T. CapabilitySdram RAS Precharge Time Award Bios Setup Utility 3.1.3 Chipset Features SetupSdram RAS-to-CAS Delay Video Bios Cacheable Dram Data Integrity ModeSystem Bios Cacheable Bit I/O Recovery Time and 16 Bit I/O Recovery TimeAGP Aperture Size MB Memory Hole At 15M-16MPCI 2.1 Compliance CPU/PCI Clock MHzPower Management Setup Spread SpectrumPM Control by APM Power ManagementAcpi Function Video Off MethodHDD Power Down Standby ModeSuspend Mode Video Off AfterResume On Ring Soft-Off by PWR-BTTNPWR Lost Resume State Resume On LAN Resume On AlarmTimer hhmmss Date of MonthResources Controlled By 5 PNP/PCI ConfigurationReset Configuration Data Assign IRQ for USB Load Fail-Safe SettingsAssign IRQ for VGA PCI Slot 1 Use IRQ to PCI Slot 4 Use IRQIntegrated Peripherals Award Bios Setup Utility Load Optimal SettingsIDE HDD Block Mode Init Display First On-Chip Primary PCI IDE and On-Chip Secondary PCI IDEUSB Keyboard Support KBC Input ClockOnboard FDC Controller UART2 Mode SelectIR Transmission Delay Onboard Serial Port 1 and Onboard Serial PortParallel Port Mode, ECP Mode Use DMA and EPP Mode Select Keyboard/Mouse Power OnSupervisor Password Award Bios Setup Utility User Password IDE HDD Auto DetectionAward Bios Setup Utility Save & Exit Setup Exit Without SavingDesktop Management Interface DMI Running the DMI UtilitySupported Softwares Using the DMI Utility Edit DMISave DMI File Supported Softwares Add DMILoad DMI File Patch Utility for Windows Supported SoftwaresError Messages Post BeepSystem Error Message Troubleshooting Checklist Monitor/DisplayFloppy Drive TroubleshootingPower Supply Troubleshooting Hard Drive Hard disk failureSystem Board Troubleshooting Serial PortKeyboard