Microsoft System Board, IBUS-BAT-1370 manual Copyright, Trademarks

Page 2

Copyright

This publication contains information that is protected by copyright. No part of it may be reproduced in any form or by any means or used to make any transformation/adaptation without the prior written permission from the copyright holders.

This publication is provided for informational purposes only. The manufacturer makes no representations or warranties with respect to the contents or use of this manual and specifically disclaims any express or implied warranties of merchantability or fitness for any particular purpose. The user will assume the entire risk of the use or the results of the use of this document. Further, the manufacturer reserves the right to revise this publication and make changes to its contents at any time, without obligation to notify any person or entity of such revisions or changes.

© 1999. All Rights Reserved.

Trademarks

Microsoft® MS-DOS®, WindowsTM, Windows® 95 and Windows® 98 are registered trademarks of Microsoft Corporation. Intel® and CeleronTM are registered trademarks of Intel Corporation. Award is a registered trademark of Award Software, Inc. Other trademarks and registered trademarks of products appearing in this manual are the properties of their respective holders.

Caution:

Danger of explosion if battery incorrectly replaced.

Replace only with the same or equivalent type recommended by the manufacturer.

Dispose of used batteries according to the battery manufacturer’s instructions.

Image 2
Contents IBUS-BAT-I370 37610914Copyright TrademarksCE, FCC and DOC Statement Table of Contents Appendix a System Error Messages Appendix B TroubleshootingChipset Features and SpecificationsFeatures ProcessorExpansion Slots ConnectorsIntroduction Desktop Management Interface DMIUSB Ports PCI Bus Master IDE ControllerIrDA Interface Introduction Intelligence Acpi ATX power supply only Virus ProtectionPackage Checklist HardwareInstallation System Board LayoutSystem Memory Hardware InstallationInstalling the DIM Module DIP Switch Settings for Processors For Factory Use Only Jumper Settings for the CPU’s Front Side Bus Hardware InstallationJumper Settings for Clearing Cmos Data On Disable Connecting the Serial Ports Serial PortsHardware Installation 2 PS/2 Mouse Port Hardware Installation Parallel Port Connecting the Parallel Printer PortIDE Hard Disk Interface Hardware Installation Floppy Disk ControllerConnecting the Floppy Disk Cable Connecting the Hard Disk Cable Adding a Second IDE Hard DriveHardware Installation USB Ports Connecting the USB PortsHardware Installation IrDA Connector Hardware Installation CPU Fan Connector Chassis Fan ConnectorHardware Installation AGP Fan Connector SB-LINK ConnectorWOL Hardware Installation Power Connector COM PW-OK 5VSBHardware Installation 14 J9 LEDs and Switches Keylock Power/Standby LED and Keylock Connector Standard Cmos Setup Basic Input/Output SystemTime Award Bios Setup UtilityDate Halt On Drive a and Drive BVideo Award Bios Setup Utility Bios Features Setup Virus WarningBoot Up Floppy Seek Quick Power On Self TestBoot Sequence CPU L1 Cache and CPU L2 CacheTypematic Delay Msec Boot Up NumLock StatusTypematic Rate Setting Typematic Rate Chars/SecOS Select for Dram 64MB HDD S.M.A.R.T. CapabilitySdram RAS Precharge Time Award Bios Setup Utility 3.1.3 Chipset Features SetupSdram RAS-to-CAS Delay Video Bios Cacheable Dram Data Integrity ModeSystem Bios Cacheable Bit I/O Recovery Time and 16 Bit I/O Recovery TimeAGP Aperture Size MB Memory Hole At 15M-16MPCI 2.1 Compliance CPU/PCI Clock MHzPower Management Setup Spread SpectrumPM Control by APM Power ManagementAcpi Function Video Off MethodHDD Power Down Standby ModeSuspend Mode Video Off AfterResume On Ring Soft-Off by PWR-BTTNPWR Lost Resume State Resume On LAN Resume On AlarmTimer hhmmss Date of MonthResources Controlled By 5 PNP/PCI ConfigurationReset Configuration Data Assign IRQ for USB Load Fail-Safe SettingsAssign IRQ for VGA PCI Slot 1 Use IRQ to PCI Slot 4 Use IRQIntegrated Peripherals Award Bios Setup Utility Load Optimal SettingsIDE HDD Block Mode Init Display First On-Chip Primary PCI IDE and On-Chip Secondary PCI IDEUSB Keyboard Support KBC Input ClockOnboard FDC Controller UART2 Mode SelectIR Transmission Delay Onboard Serial Port 1 and Onboard Serial PortParallel Port Mode, ECP Mode Use DMA and EPP Mode Select Keyboard/Mouse Power OnSupervisor Password Award Bios Setup Utility User Password IDE HDD Auto DetectionAward Bios Setup Utility Save & Exit Setup Exit Without SavingDesktop Management Interface DMI Running the DMI UtilitySupported Softwares Using the DMI Utility Edit DMISave DMI File Supported Softwares Add DMILoad DMI File Patch Utility for Windows Supported SoftwaresError Messages Post BeepSystem Error Message Troubleshooting Checklist Monitor/DisplayFloppy Drive TroubleshootingPower Supply Troubleshooting Hard Drive Hard disk failureSystem Board Troubleshooting Serial PortKeyboard