Microsoft IBUS-BAT-1370, System Board Video Off After, Modem Use IRQ, Standby Mode, Suspend Mode

Page 43

Award BIOS Setup Utility

Video Off After

N/A The system BIOS will never turn off the screen.

Suspend The screen is off when the system is in the Suspend mode.

Standby The screen is off when the system is in the Standby mode.

MODEM Use IRQ

This category is used to set an IRQ channel (IRQ 3, 4, 5, 7, 9, 10 or

11)for the external modem installed in your system. However, if the “Resume on Ring” or “Resume on LAN” field is disabled, the BIOS will mask the IRQ assigned for the modem. This is to prevent the modem or LAN from waking up the system when it is in the Suspend mode.

Standby Mode

This is user configurable only when the Power Management category is set to User Defined. When enabled and after the set time of system inactivity, video will be shut off while all other devices still operate at full speed.

Suspend Mode

This is user configurable only when the Power Management category is set to User Defined. When enabled and after the set time of system inactivity, the CPU and onboard peripherals will be shut off.

HDD Power Down

This is user configurable only when the Power Management category is set to User Defined. When enabled and after the set time of system inactivity, the hard disk drive will be powered down while all other devices remain active.

VGA Active Monitor

Enabled When the system enters the Suspend mode, it will check the status of the VGA. If the VGA is active, it will not turn the screen off. If the VGA is inactive, it will turn the screen off.

Disabled When the system enters the Suspend mode, it will immediately turn the screen off without checking the status of the VGA.

!

43

Image 43
Contents 37610914 IBUS-BAT-I370Trademarks CopyrightCE, FCC and DOC Statement Table of Contents Appendix B Troubleshooting Appendix a System Error MessagesProcessor Features and SpecificationsFeatures ChipsetDesktop Management Interface DMI ConnectorsIntroduction Expansion SlotsIrDA Interface PCI Bus Master IDE ControllerUSB Ports Introduction Intelligence Virus Protection Acpi ATX power supply onlyPackage Checklist System Board Layout HardwareInstallationInstalling the DIM Module Hardware InstallationSystem Memory DIP Switch Settings for Processors For Factory Use Only Hardware Installation Jumper Settings for the CPU’s Front Side BusJumper Settings for Clearing Cmos Data On Disable Serial Ports Connecting the Serial PortsHardware Installation 2 PS/2 Mouse Port Connecting the Parallel Printer Port Hardware Installation Parallel PortConnecting the Floppy Disk Cable Hardware Installation Floppy Disk ControllerIDE Hard Disk Interface Adding a Second IDE Hard Drive Connecting the Hard Disk CableConnecting the USB Ports Hardware Installation USB PortsHardware Installation IrDA Connector Chassis Fan Connector Hardware Installation CPU Fan ConnectorSB-LINK Connector Hardware Installation AGP Fan ConnectorWOL COM PW-OK 5VSB Hardware Installation Power ConnectorHardware Installation 14 J9 LEDs and Switches Keylock Power/Standby LED and Keylock Connector Basic Input/Output System Standard Cmos SetupDate Award Bios Setup UtilityTime Video Drive a and Drive BHalt On Virus Warning Award Bios Setup Utility Bios Features SetupCPU L1 Cache and CPU L2 Cache Quick Power On Self TestBoot Sequence Boot Up Floppy SeekTypematic Rate Chars/Sec Boot Up NumLock StatusTypematic Rate Setting Typematic Delay MsecHDD S.M.A.R.T. Capability OS Select for Dram 64MBSdram RAS-to-CAS Delay Award Bios Setup Utility 3.1.3 Chipset Features SetupSdram RAS Precharge Time Bit I/O Recovery Time and 16 Bit I/O Recovery Time Dram Data Integrity ModeSystem Bios Cacheable Video Bios CacheableCPU/PCI Clock MHz Memory Hole At 15M-16MPCI 2.1 Compliance AGP Aperture Size MBSpread Spectrum Power Management SetupVideo Off Method Power ManagementAcpi Function PM Control by APMVideo Off After Standby ModeSuspend Mode HDD Power DownPWR Lost Resume State Soft-Off by PWR-BTTNResume On Ring Date of Month Resume On AlarmTimer hhmmss Resume On LANReset Configuration Data 5 PNP/PCI ConfigurationResources Controlled By PCI Slot 1 Use IRQ to PCI Slot 4 Use IRQ Load Fail-Safe SettingsAssign IRQ for VGA Assign IRQ for USBIDE HDD Block Mode Award Bios Setup Utility Load Optimal SettingsIntegrated Peripherals KBC Input Clock On-Chip Primary PCI IDE and On-Chip Secondary PCI IDEUSB Keyboard Support Init Display FirstOnboard Serial Port 1 and Onboard Serial Port UART2 Mode SelectIR Transmission Delay Onboard FDC ControllerKeyboard/Mouse Power On Parallel Port Mode, ECP Mode Use DMA and EPP Mode SelectSupervisor Password IDE HDD Auto Detection Award Bios Setup Utility User PasswordExit Without Saving Award Bios Setup Utility Save & Exit SetupRunning the DMI Utility Desktop Management Interface DMIEdit DMI Supported Softwares Using the DMI UtilityLoad DMI File Supported Softwares Add DMISave DMI File Supported Softwares Patch Utility for WindowsPost Beep Error MessagesSystem Error Message Monitor/Display Troubleshooting ChecklistPower Supply TroubleshootingFloppy Drive Hard disk failure Troubleshooting Hard DriveKeyboard Troubleshooting Serial PortSystem Board