Microsoft System Board, IBUS-BAT-1370 manual Supported Softwares Using the DMI Utility, Edit DMI

Page 56

"Supported Softwares

4.1.2 Using the DMI Utility

Award DMI Configuration Utility Copyright Award Software Inc, 1996

[Edit DMI] [Add DMI] [Load DMI File] [Save DMI File]

s

n

s

BIOS

System

Enclosure/Chassis

Processor

Memory Controller

Memory Module

Memory Module

Memory Module

Memory Module

Cache

Cache

Port Connector

Port Connector

Port Connector

Port Connector

Port Connector

Port Connector

Port Connector

System Slots

*** BIOS Auto Detect ***

Type : BIOS Information

Handle : 0000

Vendor Name :

BIOS Version :

BIOS Starting Address Segment : F000

BIOS Build Date :

BIOS Characteristics :

Size of BIOS ROM : 0128K

↓ ←

Move cursor ENTER-Accept DEL-Delete ESC-Abort&Exit

 

 

The four menus located on top of the DMI Configuration Utility screen are Edit DMI, Add DMI, Load DMI File and Save DMI File. Use the

or (left or right) arrow keys to select a menu from the Menu

bar.

On the left side of the screen is a list of the system configuration items. Use the or (up or down) arrow keys to select an item.

The commands at the bottom of the screen will allow you to navigate through the various setup menus.

Edit DMI

1. Use the or arrow keys to select the Edit DMI menu.

2.Highlight the item on the left screen that you would like to edit by using the or arrow keys, then press <Enter>.

3.The cursor will move to the screen you select allowing you to edit information. The screen will also display the auto-detected information.

4.Press <F10> to update the edited information into the flash ROM.

56

Image 56
Contents IBUS-BAT-I370 37610914Copyright TrademarksCE, FCC and DOC Statement Table of Contents Appendix a System Error Messages Appendix B TroubleshootingFeatures and Specifications FeaturesChipset ProcessorConnectors IntroductionExpansion Slots Desktop Management Interface DMIUSB Ports PCI Bus Master IDE ControllerIrDA Interface Introduction Intelligence Acpi ATX power supply only Virus ProtectionPackage Checklist HardwareInstallation System Board LayoutSystem Memory Hardware InstallationInstalling the DIM Module DIP Switch Settings for Processors For Factory Use Only Jumper Settings for the CPU’s Front Side Bus Hardware InstallationJumper Settings for Clearing Cmos Data On Disable Connecting the Serial Ports Serial PortsHardware Installation 2 PS/2 Mouse Port Hardware Installation Parallel Port Connecting the Parallel Printer PortIDE Hard Disk Interface Hardware Installation Floppy Disk ControllerConnecting the Floppy Disk Cable Connecting the Hard Disk Cable Adding a Second IDE Hard DriveHardware Installation USB Ports Connecting the USB PortsHardware Installation IrDA Connector Hardware Installation CPU Fan Connector Chassis Fan ConnectorHardware Installation AGP Fan Connector SB-LINK ConnectorWOL Hardware Installation Power Connector COM PW-OK 5VSBHardware Installation 14 J9 LEDs and Switches Keylock Power/Standby LED and Keylock Connector Standard Cmos Setup Basic Input/Output SystemTime Award Bios Setup UtilityDate Halt On Drive a and Drive BVideo Award Bios Setup Utility Bios Features Setup Virus WarningQuick Power On Self Test Boot SequenceBoot Up Floppy Seek CPU L1 Cache and CPU L2 CacheBoot Up NumLock Status Typematic Rate SettingTypematic Delay Msec Typematic Rate Chars/SecOS Select for Dram 64MB HDD S.M.A.R.T. CapabilitySdram RAS Precharge Time Award Bios Setup Utility 3.1.3 Chipset Features SetupSdram RAS-to-CAS Delay Dram Data Integrity Mode System Bios CacheableVideo Bios Cacheable Bit I/O Recovery Time and 16 Bit I/O Recovery TimeMemory Hole At 15M-16M PCI 2.1 ComplianceAGP Aperture Size MB CPU/PCI Clock MHzPower Management Setup Spread SpectrumPower Management Acpi FunctionPM Control by APM Video Off MethodStandby Mode Suspend ModeHDD Power Down Video Off AfterResume On Ring Soft-Off by PWR-BTTNPWR Lost Resume State Resume On Alarm Timer hhmmssResume On LAN Date of MonthResources Controlled By 5 PNP/PCI ConfigurationReset Configuration Data Load Fail-Safe Settings Assign IRQ for VGAAssign IRQ for USB PCI Slot 1 Use IRQ to PCI Slot 4 Use IRQIntegrated Peripherals Award Bios Setup Utility Load Optimal SettingsIDE HDD Block Mode On-Chip Primary PCI IDE and On-Chip Secondary PCI IDE USB Keyboard SupportInit Display First KBC Input ClockUART2 Mode Select IR Transmission DelayOnboard FDC Controller Onboard Serial Port 1 and Onboard Serial PortParallel Port Mode, ECP Mode Use DMA and EPP Mode Select Keyboard/Mouse Power OnSupervisor Password Award Bios Setup Utility User Password IDE HDD Auto DetectionAward Bios Setup Utility Save & Exit Setup Exit Without SavingDesktop Management Interface DMI Running the DMI UtilitySupported Softwares Using the DMI Utility Edit DMISave DMI File Supported Softwares Add DMILoad DMI File Patch Utility for Windows Supported SoftwaresError Messages Post BeepSystem Error Message Troubleshooting Checklist Monitor/DisplayFloppy Drive TroubleshootingPower Supply Troubleshooting Hard Drive Hard disk failureSystem Board Troubleshooting Serial PortKeyboard