Microsoft System Board, IBUS-BAT-1370 manual Hardware Installation Power Connector, COM PW-OK 5VSB

Page 28

Hardware Installation

2.7.13 Power Connector

PLAT1

PLATX1

The pin assignment of the ATX power connector is shown below.

Pin	Function	Pin	Function
1	3.3V/14A	11	3.3V/14A
2	3.3V/14A	12	-12V
3	COM	13	COM
4	+5V	14	PS-ON
5	COM	15	COM
6	+5V	16	COM

7	COM	17	COM

8	PW-OK	18	-5V

9	5VSB	19	+5V
10	+12V	20	+5V

Important:

Your power supply must meet the ATX specification - supporting 3.3V/14A (minimum), otherwise your system will not boot properly.

28

Image 28

Contents IBUS-BAT-I370 37610914Copyright TrademarksCE, FCC and DOC Statement Table of Contents Appendix a System Error Messages Appendix B TroubleshootingFeatures and Specifications FeaturesChipset ProcessorConnectors IntroductionExpansion Slots Desktop Management Interface DMIIrDA Interface PCI Bus Master IDE ControllerUSB Ports Introduction Intelligence Acpi ATX power supply only Virus ProtectionPackage Checklist HardwareInstallation System Board LayoutInstalling the DIM Module Hardware InstallationSystem Memory DIP Switch Settings for Processors For Factory Use Only Jumper Settings for the CPU’s Front Side Bus Hardware InstallationJumper Settings for Clearing Cmos Data On Disable Connecting the Serial Ports Serial PortsHardware Installation 2 PS/2 Mouse Port Hardware Installation Parallel Port Connecting the Parallel Printer PortConnecting the Floppy Disk Cable Hardware Installation Floppy Disk ControllerIDE Hard Disk Interface Connecting the Hard Disk Cable Adding a Second IDE Hard DriveHardware Installation USB Ports Connecting the USB PortsHardware Installation IrDA Connector Hardware Installation CPU Fan Connector Chassis Fan ConnectorHardware Installation AGP Fan Connector SB-LINK ConnectorWOL Hardware Installation Power Connector COM PW-OK 5VSBHardware Installation 14 J9 LEDs and Switches Keylock Power/Standby LED and Keylock Connector Standard Cmos Setup Basic Input/Output SystemDate Award Bios Setup UtilityTime Video Drive a and Drive BHalt On Award Bios Setup Utility Bios Features Setup Virus WarningQuick Power On Self Test Boot SequenceBoot Up Floppy Seek CPU L1 Cache and CPU L2 CacheBoot Up NumLock Status Typematic Rate SettingTypematic Delay Msec Typematic Rate Chars/SecOS Select for Dram 64MB HDD S.M.A.R.T. CapabilitySdram RAS-to-CAS Delay Award Bios Setup Utility 3.1.3 Chipset Features SetupSdram RAS Precharge Time Dram Data Integrity Mode System Bios CacheableVideo Bios Cacheable Bit I/O Recovery Time and 16 Bit I/O Recovery TimeMemory Hole At 15M-16M PCI 2.1 ComplianceAGP Aperture Size MB CPU/PCI Clock MHzPower Management Setup Spread SpectrumPower Management Acpi FunctionPM Control by APM Video Off MethodStandby Mode Suspend ModeHDD Power Down Video Off AfterPWR Lost Resume State Soft-Off by PWR-BTTNResume On Ring Resume On Alarm Timer hhmmssResume On LAN Date of MonthReset Configuration Data 5 PNP/PCI ConfigurationResources Controlled By Load Fail-Safe Settings Assign IRQ for VGAAssign IRQ for USB PCI Slot 1 Use IRQ to PCI Slot 4 Use IRQIDE HDD Block Mode Award Bios Setup Utility Load Optimal SettingsIntegrated Peripherals On-Chip Primary PCI IDE and On-Chip Secondary PCI IDE USB Keyboard SupportInit Display First KBC Input ClockUART2 Mode Select IR Transmission DelayOnboard FDC Controller Onboard Serial Port 1 and Onboard Serial PortParallel Port Mode, ECP Mode Use DMA and EPP Mode Select Keyboard/Mouse Power OnSupervisor Password Award Bios Setup Utility User Password IDE HDD Auto DetectionAward Bios Setup Utility Save & Exit Setup Exit Without SavingDesktop Management Interface DMI Running the DMI UtilitySupported Softwares Using the DMI Utility Edit DMILoad DMI File Supported Softwares Add DMISave DMI File Patch Utility for Windows Supported SoftwaresError Messages Post BeepSystem Error Message Troubleshooting Checklist Monitor/DisplayPower Supply TroubleshootingFloppy Drive Troubleshooting Hard Drive Hard disk failureKeyboard Troubleshooting Serial PortSystem Board