Microsoft IBUS-BAT-1370, System Board manual Basic Input/Output System, Standard Cmos Setup

Page 31

!

Chapter3-AwardBIOSSetupUtility

3.1 The Basic Input/Output System

The Basic Input/Output System (BIOS) is a program that takes care of the basic level of communication between the processor and peripherals. In addition, the BIOS also contain codes for various advanced features found in this system board. This chapter explains the Setup Utility for the Award BIOS.

After you power up your system, the BIOS message appears on your screen and the memory count begins. After the memory test, the following message will appear on the screen:

Press DEL to enter setup

If the message disappears before you respond, restart your system or press the “Reset” button. You may also restart the system by pressing the <Ctrl> <Alt> and <Del> keys simultaneously.

When you press <Del>, the main program screen will appear.

ROM PCI/ISA BIOS

CMOS SETUP UTILITY

AWARD SOFTWARE, INC.

 

 

 

 

 

 

 

 

 

STANDARD CMOS SETUP

INTEGRATED PERIPHERALS

 

 

BIOS FEATURES SETUP

SUPERVISOR PASSWORD

 

 

CHIPSET FEATURES SETUP

USER PASSWORD

 

 

POWER MANAGEMENT SETUP

IDE HDD AUTO DETECTION

 

 

PNP/PCI CONFIGURATION

SAVE & EXIT SETUP

 

 

LOAD FAIL-SAFE SETTINGS

EXIT WITHOUT SAVING

 

 

LOAD OPTIMAL SETTINGS

 

 

 

 

 

 

 

 

 

 

 

 

 

Esc

:

Quit

↑↓→←

:

Select Item

 

 

F10

:

Save & Exit Setup

(Shift) F2

:

Change Color

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.1.1 Standard CMOS Setup

Use the arrow keys to highlight “Standard CMOS Setup” and press <Enter>. A screen similar to the one on the next page will appear.

31

Image 31
Contents 37610914 IBUS-BAT-I370Trademarks CopyrightCE, FCC and DOC Statement Table of Contents Appendix B Troubleshooting Appendix a System Error MessagesProcessor Features and SpecificationsFeatures ChipsetDesktop Management Interface DMI ConnectorsIntroduction Expansion SlotsIrDA Interface PCI Bus Master IDE ControllerUSB Ports Introduction Intelligence Virus Protection Acpi ATX power supply onlyPackage Checklist System Board Layout HardwareInstallationInstalling the DIM Module Hardware InstallationSystem Memory DIP Switch Settings for Processors For Factory Use Only Hardware Installation Jumper Settings for the CPU’s Front Side BusJumper Settings for Clearing Cmos Data On Disable Serial Ports Connecting the Serial PortsHardware Installation 2 PS/2 Mouse Port Connecting the Parallel Printer Port Hardware Installation Parallel PortConnecting the Floppy Disk Cable Hardware Installation Floppy Disk ControllerIDE Hard Disk Interface Adding a Second IDE Hard Drive Connecting the Hard Disk CableConnecting the USB Ports Hardware Installation USB PortsHardware Installation IrDA Connector Chassis Fan Connector Hardware Installation CPU Fan ConnectorSB-LINK Connector Hardware Installation AGP Fan ConnectorWOL COM PW-OK 5VSB Hardware Installation Power ConnectorHardware Installation 14 J9 LEDs and Switches Keylock Power/Standby LED and Keylock Connector Basic Input/Output System Standard Cmos SetupDate Award Bios Setup UtilityTime Video Drive a and Drive BHalt On Virus Warning Award Bios Setup Utility Bios Features SetupCPU L1 Cache and CPU L2 Cache Quick Power On Self TestBoot Sequence Boot Up Floppy SeekTypematic Rate Chars/Sec Boot Up NumLock StatusTypematic Rate Setting Typematic Delay MsecHDD S.M.A.R.T. Capability OS Select for Dram 64MBSdram RAS-to-CAS Delay Award Bios Setup Utility 3.1.3 Chipset Features SetupSdram RAS Precharge Time Bit I/O Recovery Time and 16 Bit I/O Recovery Time Dram Data Integrity ModeSystem Bios Cacheable Video Bios CacheableCPU/PCI Clock MHz Memory Hole At 15M-16MPCI 2.1 Compliance AGP Aperture Size MBSpread Spectrum Power Management SetupVideo Off Method Power ManagementAcpi Function PM Control by APMVideo Off After Standby ModeSuspend Mode HDD Power DownPWR Lost Resume State Soft-Off by PWR-BTTNResume On Ring Date of Month Resume On AlarmTimer hhmmss Resume On LANReset Configuration Data 5 PNP/PCI ConfigurationResources Controlled By PCI Slot 1 Use IRQ to PCI Slot 4 Use IRQ Load Fail-Safe SettingsAssign IRQ for VGA Assign IRQ for USBIDE HDD Block Mode Award Bios Setup Utility Load Optimal SettingsIntegrated Peripherals KBC Input Clock On-Chip Primary PCI IDE and On-Chip Secondary PCI IDEUSB Keyboard Support Init Display FirstOnboard Serial Port 1 and Onboard Serial Port UART2 Mode SelectIR Transmission Delay Onboard FDC ControllerKeyboard/Mouse Power On Parallel Port Mode, ECP Mode Use DMA and EPP Mode SelectSupervisor Password IDE HDD Auto Detection Award Bios Setup Utility User PasswordExit Without Saving Award Bios Setup Utility Save & Exit SetupRunning the DMI Utility Desktop Management Interface DMIEdit DMI Supported Softwares Using the DMI UtilityLoad DMI File Supported Softwares Add DMISave DMI File Supported Softwares Patch Utility for WindowsPost Beep Error MessagesSystem Error Message Monitor/Display Troubleshooting ChecklistPower Supply TroubleshootingFloppy Drive Hard disk failure Troubleshooting Hard DriveKeyboard Troubleshooting Serial PortSystem Board