Microsoft IBUS-BAT-1370, System Board manual Introduction Intelligence

Page 9

Introduction

1.1.2 Intelligence

Automatic CPU/Chassis Fan Off

The CPU and chassis fans will automatically turn off once the system enters the Suspend mode.

Dual Function Power Button (ATX power supply only)

Depending on the setting in the BIOS setup, this switch will allow the system to enter the Soft-Off or Suspend mode.

External Modem Ring-on (ATX power supply only)

The Modem Ring-on feature allows the system that is in the Suspend mode or Soft Power Off mode to wake-up/power-on to respond to incoming calls.

Note:

This feature supports external modem only.

RTC Timer to Power-on the System (ATX power supply only)

The RTC installed on the system board allows your system to automatically power-on on the set date and time.

Wake-On-LAN Ready (ATX power supply only)

The Wake-On-LAN function allows the network to remotely wake up a Soft Power Down (Soft-Off) PC. Your LAN card must support the remote wakeup function.

Important:

The 5VSB power source of your power supply must support 720mA (minimum).

Wake-On-Keyboard/Wake-On-Mouse (ATX power supply only)

This function allows you to use the keyboard or mouse to power- on the system. Refer to “Jumper Settings for Wake-On-Keyboard/ Wake-On-Mouse” in chapter 2 and “Keyboard/Mouse Power On” in the Integrated Peripherals setup of the Award BIOS in chapter 3 for more information.

￿

9

Image 9
Contents 37610914 IBUS-BAT-I370Trademarks CopyrightCE, FCC and DOC Statement Table of Contents Appendix B Troubleshooting Appendix a System Error MessagesFeatures Features and SpecificationsChipset ProcessorIntroduction ConnectorsExpansion Slots Desktop Management Interface DMIPCI Bus Master IDE Controller IrDA InterfaceUSB Ports Introduction Intelligence Virus Protection Acpi ATX power supply onlyPackage Checklist System Board Layout HardwareInstallationHardware Installation Installing the DIM ModuleSystem Memory DIP Switch Settings for Processors For Factory Use Only Hardware Installation Jumper Settings for the CPU’s Front Side BusJumper Settings for Clearing Cmos Data On Disable Serial Ports Connecting the Serial PortsHardware Installation 2 PS/2 Mouse Port Connecting the Parallel Printer Port Hardware Installation Parallel PortHardware Installation Floppy Disk Controller Connecting the Floppy Disk CableIDE Hard Disk Interface Adding a Second IDE Hard Drive Connecting the Hard Disk CableConnecting the USB Ports Hardware Installation USB PortsHardware Installation IrDA Connector Chassis Fan Connector Hardware Installation CPU Fan ConnectorSB-LINK Connector Hardware Installation AGP Fan ConnectorWOL COM PW-OK 5VSB Hardware Installation Power ConnectorHardware Installation 14 J9 LEDs and Switches Keylock Power/Standby LED and Keylock Connector Basic Input/Output System Standard Cmos SetupAward Bios Setup Utility DateTime Drive a and Drive B VideoHalt On Virus Warning Award Bios Setup Utility Bios Features SetupBoot Sequence Quick Power On Self TestBoot Up Floppy Seek CPU L1 Cache and CPU L2 CacheTypematic Rate Setting Boot Up NumLock StatusTypematic Delay Msec Typematic Rate Chars/SecHDD S.M.A.R.T. Capability OS Select for Dram 64MBAward Bios Setup Utility 3.1.3 Chipset Features Setup Sdram RAS-to-CAS DelaySdram RAS Precharge Time System Bios Cacheable Dram Data Integrity ModeVideo Bios Cacheable Bit I/O Recovery Time and 16 Bit I/O Recovery TimePCI 2.1 Compliance Memory Hole At 15M-16MAGP Aperture Size MB CPU/PCI Clock MHzSpread Spectrum Power Management SetupAcpi Function Power ManagementPM Control by APM Video Off MethodSuspend Mode Standby ModeHDD Power Down Video Off AfterSoft-Off by PWR-BTTN PWR Lost Resume StateResume On Ring Timer hhmmss Resume On AlarmResume On LAN Date of Month5 PNP/PCI Configuration Reset Configuration DataResources Controlled By Assign IRQ for VGA Load Fail-Safe SettingsAssign IRQ for USB PCI Slot 1 Use IRQ to PCI Slot 4 Use IRQAward Bios Setup Utility Load Optimal Settings IDE HDD Block ModeIntegrated Peripherals USB Keyboard Support On-Chip Primary PCI IDE and On-Chip Secondary PCI IDEInit Display First KBC Input ClockIR Transmission Delay UART2 Mode SelectOnboard FDC Controller Onboard Serial Port 1 and Onboard Serial PortKeyboard/Mouse Power On Parallel Port Mode, ECP Mode Use DMA and EPP Mode SelectSupervisor Password IDE HDD Auto Detection Award Bios Setup Utility User PasswordExit Without Saving Award Bios Setup Utility Save & Exit SetupRunning the DMI Utility Desktop Management Interface DMIEdit DMI Supported Softwares Using the DMI UtilitySupported Softwares Add DMI Load DMI FileSave DMI File Supported Softwares Patch Utility for WindowsPost Beep Error MessagesSystem Error Message Monitor/Display Troubleshooting ChecklistTroubleshooting Power SupplyFloppy Drive Hard disk failure Troubleshooting Hard DriveTroubleshooting Serial Port KeyboardSystem Board