Nokia M1112 manual

Page 2

M1112

ADSL (over ISDN) Router

Administrator Manual

C33907.20 A0

C33907001SE_00

E Copyright Nokia Networks Oy

Image 2

Contents Nokia M1112 M1112 M1112 Administrator Manual Document History Document Date CommentM1112 Administrator Manual Contents Chapter Interfaces and indicator lights Appendix a Technical specifications Viii Chapter Introduction to Nokia M1112 Nokia M1112M1112 Administrator Manual Internet access Applications1High-speed Internet access Remote work RAN L2TPInterfaces FeaturesLAN interconnection Route/tunnel IP only LAN interface Route/tunnel IP, bridge all other including IPRouting Internal host/gateway interfaceData VCC operation BridgingNetwork Address Port Translation Dynamic Host Configuration Protocol ATM and AdslPoint-to-Point Tunneling Protocol Pptp Payload encapsulations Weighted Fair Queueing Class of ServicePoint-to-Point Protocol over Ethernet PPPoE Management Dedicated management channel6Dedicated management channel M1112 Administrator Manual Chapter Interfaces and indicator lights InterfacesAdsl interface Signal Direction MDI signalEthernet interface EthernetSignal Direction MDI signal M5112-ter Minal Command line interfaceSignal Indicator lights 5M1112 front panel indicatorsOff Hardware malfunction during startup M1112 Administrator Manual Chapter Installing Nokia M1112 M1112 default settings192.168.1.1 Config mode level Parameter SettingM1112 255.255.255.0Step-by-step installation procedure Managing M1112 for instructions on how to configure M1112 Chapter Managing M1112 Operational examplesRouting/tunneling IP, bridging other protocols Block diagramRouting/tunneling IP only Routing/tunneling IP, bridging all protocols including IP Bridging only Typical configuration tasksConfiguring Dhcp and DNS Configuring static and dynamic routing File system and downloading new firmware using Tftp Use CLI to issue Downloading configuration or application from monitorBrowser management Opening a connection Main Service Providers pages 3Service Providers page with PPP configuration4Service Providers page with Pptp configuration Local Network pages Local portsM1112 Administrator Manual 6Local Network Dhcp Napt 8Local Network Routing Statistics Restart 10 RestartCommand line interface CLI Save ConfigSetting Value M1112 Administrator Manual Main mode commands Command Show diagnostic logCommand Show DSL line status Command Show Ethernet interface statusManaging M1112 Command Show ATM statusCommand Show bridge interface status Command Show Pptp information Command Show bridging statisticsCommand Show bridging table Command Show Address Resolution Protocol ARP table Command Show IP interfacesCommand Show IP statistics Command Show IP cache table and statisticsCommand Show IP routing table VbridgeCommand Show Internet Control Message Protocol statistics Command Show User Datagram Protocol statisticsCommand Show Snmp statistics Command Show Transmission Control statisticsCommand Show Routing Information Protocol statistics VCC3 Command Show Domain Name Server entry table and statis Tics Command Show M1112 information Command Show running configuration Command Show startup configuration Command Show default configurationCommand Ping Command Show configuration fileCommand Show debug status Command ATMping Command Switch off debugCommand Show contents of file directory Command Copy fileCommand Download new firmware Command Rename fileCommand Delete file Command Save log to a default file Command Execute a command batchCommand Save log to file Command Clear counters Command Save configuration to fileCommand Restore configuration Command Fast restart M1112 Command Reset subsystemCommand Logout Command Switch to configuration mode Configuration mode commandsCommand Restart M1112 Command Return to root levelRoot level commands Command Show current running configurationCommand Set configuration session timeout System level commandsCommand Assign hostname Password level command Command Assign new passwordCommand Switch on/off IP function in Ethernet interface Ethernet level commandsCommand Switch on/off bridging M1112conf-eth#ip rip-receive VCC ATM channel commands Command Activate ATM channelCommand Set PPP password Command Switch on/off PPP authenticationCommand Set PPP username Command Switch on/off IP function on ATM channel Command Switch on/off RIP send function on ATM channelCommand Switch on/off RIP receive function on ATM channel Command Enable Network Address Port TranslationCommand Set server support entry Command Disable/enable management through the ATM chan NelCommand Switch on/off RIP receive function in vbridge Vbridge commandsCommand Switch on/off IP function in vbridge Command Disable/enable management through the vbridgeCommand Activate dedicated management channel Dedicated management channel commandsCommand Switch on/off VCC-to-VCC bridging Common commands Command Set PPP packet sizeCommand Set max-terminate parameter value Command Set PPP restart time parameterCommand Set max-config parameter value Command Add/delete IP route Command Set max-failure parameter valueCommand Switch on/off IP cache Command Define and activate host acces list Command Switch on/off dynamic host configuration protocolCommand Set Dhcp address range Command Set DNS address for Dhcp clientsCommand Set Domain name server address Command Set Dhcp server lease timeCommand Set Dhcp pool domain name Command Switch on/off weighted fair queueing M1112 Administrator Manual Ethernet interface FeaturesATM over Adsl RoutingDedicated ATM management channel Command line interface CLI for local managementIndicator lights Management through payloadAmbient conditions Mechanical construction and power supplyAmbient conditions, EMC and safety Mechanical constructionSafety Digital Subscriber Line Access Multiplexer Asynchronous transfer modeCommand line interface Intergrated services digital networkTerms 10Base-T Encapsulation Multiplexer Web browser Glossary-6