Nokia M1112 manual Features, LAN interconnection, Interfaces

Page 15

M1112 Administrator Manual

LAN interconnection

M1112 can also be used for corporate branch office LAN interconnection. As a bridge, M1112 enables all network protocols to be used on the corporate network.

LAN
10Base-T	DSLAM
	ATM
	network
Remote
office 1
Remote
office 2	Company
	Company
	bridge
Remote
office 3
	Corporate
10Base-T	network

Figure 2-3LAN interconnection

2.2Features

M1112 can operate as a bridge and/or Internet Protocol (IP) router between the Ethernet and the virtual channels of ADSL/ATM interfaces supporting both dynamic and static routing.

2.2.1Interfaces

M1112 has the following interfaces:

D Four Ethernet interfaces (LAN) D 8 ATM VCC interfaces

D ATM VCC management interface

2-4

E Copyright Nokia Networks Oy

C33907001SE_00

Image 15

Contents Nokia M1112 M1112 M1112 Administrator Manual Document Date Comment Document HistoryM1112 Administrator Manual Contents Chapter Interfaces and indicator lights Appendix a Technical specifications Viii Nokia M1112 Chapter Introduction to Nokia M1112M1112 Administrator Manual Applications Internet access1High-speed Internet access RAN L2TP Remote workFeatures LAN interconnectionInterfaces Route/tunnel IP only Route/tunnel IP, bridge all other including IP LAN interfaceBridging Internal host/gateway interfaceData VCC operation RoutingNetwork Address Port Translation ATM and Adsl Dynamic Host Configuration ProtocolPoint-to-Point Tunneling Protocol Pptp Weighted Fair Queueing Class of Service Point-to-Point Protocol over Ethernet PPPoEPayload encapsulations Dedicated management channel Management6Dedicated management channel M1112 Administrator Manual Interfaces Chapter Interfaces and indicator lightsEthernet Signal Direction MDI signalEthernet interface Adsl interfaceCommand line interface SignalSignal Direction MDI signal M5112-ter Minal 5M1112 front panel indicators Indicator lightsOff Hardware malfunction during startup M1112 Administrator Manual M1112 default settings Chapter Installing Nokia M1112255.255.255.0 Config mode level Parameter SettingM1112 192.168.1.1Step-by-step installation procedure Managing M1112 for instructions on how to configure M1112 Operational examples Chapter Managing M1112Block diagram Routing/tunneling IP onlyRouting/tunneling IP, bridging other protocols Routing/tunneling IP, bridging all protocols including IP Typical configuration tasks Configuring Dhcp and DNSBridging only Configuring static and dynamic routing File system and downloading new firmware using Tftp Downloading configuration or application from monitor Use CLI to issueBrowser management Opening a connection Main 3Service Providers page with PPP configuration Service Providers pages4Service Providers page with Pptp configuration Local ports Local Network pagesM1112 Administrator Manual 6Local Network Dhcp Napt 8Local Network Routing Statistics 10 Restart RestartSave Config Command line interface CLISetting Value M1112 Administrator Manual Command Show diagnostic log Main mode commandsCommand Show Ethernet interface status Command Show DSL line statusCommand Show ATM status Command Show bridge interface statusManaging M1112 Command Show bridging statistics Command Show bridging tableCommand Show Pptp information Command Show IP interfaces Command Show Address Resolution Protocol ARP tableCommand Show IP cache table and statistics Command Show IP statisticsVbridge Command Show IP routing tableCommand Show User Datagram Protocol statistics Command Show Internet Control Message Protocol statisticsCommand Show Transmission Control statistics Command Show Routing Information Protocol statisticsCommand Show Snmp statistics VCC3 Command Show Domain Name Server entry table and statis Tics Command Show M1112 information Command Show running configuration Command Show default configuration Command Show startup configurationCommand Show configuration file Command Show debug statusCommand Ping Command Switch off debug Command ATMpingCommand Copy file Command Show contents of file directoryCommand Rename file Command Delete fileCommand Download new firmware Command Execute a command batch Command Save log to fileCommand Save log to a default file Command Save configuration to file Command Restore configurationCommand Clear counters Command Reset subsystem Command LogoutCommand Fast restart M1112 Command Return to root level Configuration mode commandsCommand Restart M1112 Command Switch to configuration modeCommand Show current running configuration Root level commandsSystem level commands Command Assign hostnameCommand Set configuration session timeout Command Assign new password Password level commandEthernet level commands Command Switch on/off bridgingCommand Switch on/off IP function in Ethernet interface M1112conf-eth#ip rip-receive Command Activate ATM channel VCC ATM channel commandsCommand Switch on/off PPP authentication Command Set PPP usernameCommand Set PPP password Command Switch on/off RIP send function on ATM channel Command Switch on/off IP function on ATM channelCommand Enable Network Address Port Translation Command Switch on/off RIP receive function on ATM channelCommand Disable/enable management through the ATM chan Nel Command Set server support entryCommand Disable/enable management through the vbridge Vbridge commandsCommand Switch on/off IP function in vbridge Command Switch on/off RIP receive function in vbridgeDedicated management channel commands Command Switch on/off VCC-to-VCC bridgingCommand Activate dedicated management channel Command Set PPP packet size Common commandsCommand Set PPP restart time parameter Command Set max-config parameter valueCommand Set max-terminate parameter value Command Set max-failure parameter value Command Switch on/off IP cacheCommand Add/delete IP route Command Switch on/off dynamic host configuration protocol Command Define and activate host acces listCommand Set DNS address for Dhcp clients Command Set Dhcp address rangeCommand Set Dhcp server lease time Command Set Dhcp pool domain nameCommand Set Domain name server address Command Switch on/off weighted fair queueing M1112 Administrator Manual Routing FeaturesATM over Adsl Ethernet interfaceManagement through payload Command line interface CLI for local managementIndicator lights Dedicated ATM management channelMechanical construction Mechanical construction and power supplyAmbient conditions, EMC and safety Ambient conditionsSafety Intergrated services digital network Asynchronous transfer modeCommand line interface Digital Subscriber Line Access MultiplexerTerms 10Base-T Encapsulation Multiplexer Web browser Glossary-6