Nokia M1112 manual Command Show startup configuration, Command Show default configuration

Page 71

M1112 Administrator Manual

Command	Show startup configuration


Description	Displays the startup configuration of your M1112. This
	is the configuration saved in the startup.cfg file. Star-
	tup.cfg file is activated when M1112 is switched on. If
	the startup.cfg file is missing, the default configuration
	is used.

Syntax	show config startup

Arguments	None

Example

M1112> show config startup system

hostname M1112

eth

ip address 192.168.172.148 255.255.255.128

vcc1

pvc 0 155 tunneled-ppp-vc bridging

vbridge mngtvcc common M1112>

Command	Show default configuration


Description	Displays the default configuration of M1112. M1112
	uses this configuration if the startup.cfg file is missing.

Syntax	show config default

Arguments	None

Example

M1112> show config default system

hostname Mxx

eth

bridging

vcc1

pvc 0 100 eth-llc bridging

vbridge mngtvcc common M1112>

5-36

E Copyright Nokia Networks Oy

C33907001SE_00

Image 71

Contents Nokia M1112 M1112 M1112 Administrator Manual Document Date Comment Document HistoryM1112 Administrator Manual Contents Chapter Interfaces and indicator lights Appendix a Technical specifications Viii Nokia M1112 Chapter Introduction to Nokia M1112M1112 Administrator Manual Applications Internet access1High-speed Internet access RAN L2TP Remote workInterfaces FeaturesLAN interconnection Route/tunnel IP only Route/tunnel IP, bridge all other including IP LAN interfaceBridging Internal host/gateway interfaceData VCC operation RoutingNetwork Address Port Translation ATM and Adsl Dynamic Host Configuration ProtocolPoint-to-Point Tunneling Protocol Pptp Payload encapsulations Weighted Fair Queueing Class of ServicePoint-to-Point Protocol over Ethernet PPPoE Dedicated management channel Management6Dedicated management channel M1112 Administrator Manual Interfaces Chapter Interfaces and indicator lightsEthernet Signal Direction MDI signalEthernet interface Adsl interfaceSignal Direction MDI signal M5112-ter Minal Command line interfaceSignal 5M1112 front panel indicators Indicator lightsOff Hardware malfunction during startup M1112 Administrator Manual M1112 default settings Chapter Installing Nokia M1112255.255.255.0 Config mode level Parameter SettingM1112 192.168.1.1Step-by-step installation procedure Managing M1112 for instructions on how to configure M1112 Operational examples Chapter Managing M1112Routing/tunneling IP, bridging other protocols Block diagramRouting/tunneling IP only Routing/tunneling IP, bridging all protocols including IP Bridging only Typical configuration tasksConfiguring Dhcp and DNS Configuring static and dynamic routing File system and downloading new firmware using Tftp Downloading configuration or application from monitor Use CLI to issueBrowser management Opening a connection Main 3Service Providers page with PPP configuration Service Providers pages4Service Providers page with Pptp configuration Local ports Local Network pagesM1112 Administrator Manual 6Local Network Dhcp Napt 8Local Network Routing Statistics 10 Restart RestartSave Config Command line interface CLISetting Value M1112 Administrator Manual Command Show diagnostic log Main mode commandsCommand Show Ethernet interface status Command Show DSL line statusManaging M1112 Command Show ATM statusCommand Show bridge interface status Command Show Pptp information Command Show bridging statisticsCommand Show bridging table Command Show IP interfaces Command Show Address Resolution Protocol ARP tableCommand Show IP cache table and statistics Command Show IP statisticsVbridge Command Show IP routing tableCommand Show User Datagram Protocol statistics Command Show Internet Control Message Protocol statisticsCommand Show Snmp statistics Command Show Transmission Control statisticsCommand Show Routing Information Protocol statistics VCC3 Command Show Domain Name Server entry table and statis Tics Command Show M1112 information Command Show running configuration Command Show default configuration Command Show startup configurationCommand Ping Command Show configuration fileCommand Show debug status Command Switch off debug Command ATMpingCommand Copy file Command Show contents of file directoryCommand Download new firmware Command Rename fileCommand Delete file Command Save log to a default file Command Execute a command batchCommand Save log to file Command Clear counters Command Save configuration to fileCommand Restore configuration Command Fast restart M1112 Command Reset subsystemCommand Logout Command Return to root level Configuration mode commandsCommand Restart M1112 Command Switch to configuration modeCommand Show current running configuration Root level commandsCommand Set configuration session timeout System level commandsCommand Assign hostname Command Assign new password Password level commandCommand Switch on/off IP function in Ethernet interface Ethernet level commandsCommand Switch on/off bridging M1112conf-eth#ip rip-receive Command Activate ATM channel VCC ATM channel commandsCommand Set PPP password Command Switch on/off PPP authenticationCommand Set PPP username Command Switch on/off RIP send function on ATM channel Command Switch on/off IP function on ATM channelCommand Enable Network Address Port Translation Command Switch on/off RIP receive function on ATM channelCommand Disable/enable management through the ATM chan Nel Command Set server support entryCommand Disable/enable management through the vbridge Vbridge commandsCommand Switch on/off IP function in vbridge Command Switch on/off RIP receive function in vbridgeCommand Activate dedicated management channel Dedicated management channel commandsCommand Switch on/off VCC-to-VCC bridging Command Set PPP packet size Common commandsCommand Set max-terminate parameter value Command Set PPP restart time parameterCommand Set max-config parameter value Command Add/delete IP route Command Set max-failure parameter valueCommand Switch on/off IP cache Command Switch on/off dynamic host configuration protocol Command Define and activate host acces listCommand Set DNS address for Dhcp clients Command Set Dhcp address rangeCommand Set Domain name server address Command Set Dhcp server lease timeCommand Set Dhcp pool domain name Command Switch on/off weighted fair queueing M1112 Administrator Manual Routing FeaturesATM over Adsl Ethernet interfaceManagement through payload Command line interface CLI for local managementIndicator lights Dedicated ATM management channelMechanical construction Mechanical construction and power supplyAmbient conditions, EMC and safety Ambient conditionsSafety Intergrated services digital network Asynchronous transfer modeCommand line interface Digital Subscriber Line Access MultiplexerTerms 10Base-T Encapsulation Multiplexer Web browser Glossary-6