Nokia M1112 manual VCC ATM channel commands, Command Activate ATM channel

Page 85

M1112 Administrator Manual

VCC (ATM channel) commands

Command

Activate ATM channel

 

 

 

 

Description

Activates an ATM channel and sets the encapsulation

 

for that channel.

 

 

Syntax

[no] pvc <vpi> <vci> <encap>

 

 

Arguments

no deactivates the ATM channel.

 

vpi is the Virtual Path Identifier of the ATM channel.

 

Possible values are 0...255.

 

vci is the Virtual Channel Identifier of the ATM chan-

 

nel. Possible values are 0...65535.

 

encap is the encapsulation of the ATM channel. The

 

encapsulations are auto-llc, eth-llc, ip-llc,

 

ppp-vc, and tunneled-ppp-vc.auto-llc en-

 

capsulates the routed packets in ip-llc and the bridged

 

packets in eth-llc.

 

 

Example

M1112(conf-vccx)#pvc 0 100 ip-llc

M1112(conf-vccx)#

Command

Switch on/off bridging

 

 

 

 

Description

Switches bridging on/off on the specified ATM channel.

 

 

Syntax

[no] bridging

 

 

Arguments

no switches off bridging.

 

 

Example

M1112(conf-vccx)#bridging

M1112(conf-vccx)#

5-50

E Copyright Nokia Networks Oy

C33907001SE_00

Page 84 Page 86
Image 85
Page 84 Page 86
Contents Nokia M1112 M1112 M1112 Administrator Manual Document Date Comment Document HistoryM1112 Administrator Manual Contents Chapter Interfaces and indicator lights Appendix a Technical specifications Viii Nokia M1112 Chapter Introduction to Nokia M1112M1112 Administrator Manual Applications Internet access1High-speed Internet access RAN L2TP Remote workLAN interconnection FeaturesInterfaces Route/tunnel IP only Route/tunnel IP, bridge all other including IP LAN interfaceData VCC operation Internal host/gateway interfaceRouting BridgingNetwork Address Port Translation ATM and Adsl Dynamic Host Configuration ProtocolPoint-to-Point Tunneling Protocol Pptp Point-to-Point Protocol over Ethernet PPPoE Weighted Fair Queueing Class of ServicePayload encapsulations Dedicated management channel Management6Dedicated management channel M1112 Administrator Manual Interfaces Chapter Interfaces and indicator lightsEthernet interface Signal Direction MDI signalAdsl interface EthernetSignal Command line interfaceSignal Direction MDI signal M5112-ter Minal 5M1112 front panel indicators Indicator lightsOff Hardware malfunction during startup M1112 Administrator Manual M1112 default settings Chapter Installing Nokia M1112M1112 Config mode level Parameter Setting192.168.1.1 255.255.255.0Step-by-step installation procedure Managing M1112 for instructions on how to configure M1112 Operational examples Chapter Managing M1112Routing/tunneling IP only Block diagramRouting/tunneling IP, bridging other protocols Routing/tunneling IP, bridging all protocols including IP Configuring Dhcp and DNS Typical configuration tasksBridging only Configuring static and dynamic routing File system and downloading new firmware using Tftp Downloading configuration or application from monitor Use CLI to issueBrowser management Opening a connection Main 3Service Providers page with PPP configuration Service Providers pages4Service Providers page with Pptp configuration Local ports Local Network pagesM1112 Administrator Manual 6Local Network Dhcp Napt 8Local Network Routing Statistics 10 Restart RestartSave Config Command line interface CLISetting Value M1112 Administrator Manual Command Show diagnostic log Main mode commandsCommand Show Ethernet interface status Command Show DSL line statusCommand Show bridge interface status Command Show ATM statusManaging M1112 Command Show bridging table Command Show bridging statisticsCommand Show Pptp information Command Show IP interfaces Command Show Address Resolution Protocol ARP tableCommand Show IP cache table and statistics Command Show IP statisticsVbridge Command Show IP routing tableCommand Show User Datagram Protocol statistics Command Show Internet Control Message Protocol statisticsCommand Show Routing Information Protocol statistics Command Show Transmission Control statisticsCommand Show Snmp statistics VCC3 Command Show Domain Name Server entry table and statis Tics Command Show M1112 information Command Show running configuration Command Show default configuration Command Show startup configurationCommand Show debug status Command Show configuration fileCommand Ping Command Switch off debug Command ATMpingCommand Copy file Command Show contents of file directoryCommand Delete file Command Rename fileCommand Download new firmware Command Save log to file Command Execute a command batchCommand Save log to a default file Command Restore configuration Command Save configuration to fileCommand Clear counters Command Logout Command Reset subsystemCommand Fast restart M1112 Command Restart M1112 Configuration mode commandsCommand Switch to configuration mode Command Return to root levelCommand Show current running configuration Root level commandsCommand Assign hostname System level commandsCommand Set configuration session timeout Command Assign new password Password level commandCommand Switch on/off bridging Ethernet level commandsCommand Switch on/off IP function in Ethernet interface M1112conf-eth#ip rip-receive Command Activate ATM channel VCC ATM channel commandsCommand Set PPP username Command Switch on/off PPP authenticationCommand Set PPP password Command Switch on/off RIP send function on ATM channel Command Switch on/off IP function on ATM channelCommand Enable Network Address Port Translation Command Switch on/off RIP receive function on ATM channelCommand Disable/enable management through the ATM chan Nel Command Set server support entryCommand Switch on/off IP function in vbridge Vbridge commandsCommand Switch on/off RIP receive function in vbridge Command Disable/enable management through the vbridgeCommand Switch on/off VCC-to-VCC bridging Dedicated management channel commandsCommand Activate dedicated management channel Command Set PPP packet size Common commandsCommand Set max-config parameter value Command Set PPP restart time parameterCommand Set max-terminate parameter value Command Switch on/off IP cache Command Set max-failure parameter valueCommand Add/delete IP route Command Switch on/off dynamic host configuration protocol Command Define and activate host acces listCommand Set DNS address for Dhcp clients Command Set Dhcp address rangeCommand Set Dhcp pool domain name Command Set Dhcp server lease timeCommand Set Domain name server address Command Switch on/off weighted fair queueing M1112 Administrator Manual ATM over Adsl FeaturesEthernet interface RoutingIndicator lights Command line interface CLI for local managementDedicated ATM management channel Management through payloadAmbient conditions, EMC and safety Mechanical construction and power supplyAmbient conditions Mechanical constructionSafety Command line interface Asynchronous transfer modeDigital Subscriber Line Access Multiplexer Intergrated services digital networkTerms 10Base-T Encapsulation Multiplexer Web browser Glossary-6
Top Page Image Contents