JVC DLA-SX21E, DLA-SX21SU, DLA-SX21SE instruction manual Power Off, Adjusting the Sound Volume

Page 11

Basic Operations

5. Adjusting the Sound Volume

To increase the volume: press VOLUME ª (0 ➞ 50)

	To lower the volume : press VOLUME · (50 ➞ 0)
VOL.	VOLUME

STAND BY

LAMP TEMP OPERATE

PC VIDEO

V-KEYSTONE H-KEYSTONE

VOL.

MENUEXIT

ENTER

OPERATE

5

Projector:	Remote Control
Control panel	Unit
Audio-Vol	12

Screen display

When “Menu display” (☞ page 39) is set to “15sec”, after pressing the VOL- UME button, the sound volume display will appear on the screen for about 15 seconds.

(Press EXIT button to immediately re- move the Audio-vol display.)

Audio-Vol

OPERATE

PC VIDEO

W

V-KEYSTONEH-KEYSTONE SCREEN DIGITAL ZOOM

	S
	FREEZE
VOLUME FOCUS	QUICK ALIGN.
MENU	EXIT

OPERATE

5

Note

•When the sound volume is displayed on the screen, pressing the PRESET button will reset the set value to “0”.

Power Off

1. Press the OPERATE button on the projector (or the OP- ERATE button on the remote control unit ) for 1 second or more.

The OPERATE indicator will disappear, the STAND BY indicator starts to blink, and the projector goes into the cool-down mode.

●The STAND BY indicator will continue blinking for approximately 90 seconds as the temperature of the light source lamp cools (Cool Down Mode).

ENGLISH

ENTER

PRESETHIDE

OPERATE

	OPERATE
Projector:	Remote Control
Control Panel	Unit

Turn off Turn on

STAND BY

LAMP TEMP OPERATE

Projector: Indicator part

Note

•The OPERATE button will not work for approximately 1 minute from when the light-source lamp is turned on. Wait approxi- mately 1 minute before pressing.

Caution

•Please do not pull out the plug from the power source when the STAND BY indicator is blinking. It will shorten the life of the lamp and cause a malfunction.

27

Image 11

Contents DLA-SX21U/DLA-SX21E Machine Noise Information Germany only FCC Information U.S.A. onlyDo not allow any unqualified person to install the unit Safety PrecautionDo not cut off the main plug from this equipment Wire which is coloured green-and-yellow must be conHow To Replace The Fuse Brown LiveCare Using the screen mode switch functionAbout burning-in of the D-ILA device Viewing conditionsAccessories Contents Computer signals Connecting to Various DevicesSignals that can be input into the projector Video signalsHorPixels Ver Lines KHz Connecting to Various Devices Allowable input signals SignalSelecting the image to be projected Basic Operation ProceduresPower On Basic OperationsScreen display Display using the direct buttonsAdjusting the Focus Ring Focus for DLA-SX21U/DLA- SX21E Basic OperationsAdjusting the Sound Volume Power OffMain menu Adjustments and Settings Using MenusMenu Structure Video Input selectionWhen PC input is selected Submenu Adjustments and Settings Using MenusWhen no image signal is inputted Main Set up menu Displayed only when PC is selectedLight source lamp and its lamp time Procedure for lamp replacementAbout lamp replacement Replacing the LampClose the handle, and tighten the screw Replacing the LampRemove the lamp unit Insert the new lamp unit until it is fullyTo ensure the lamp time has been reset Resetting the lamp timeBy mode Press the EXIT, HIDE, Preset buttons on the remoteReinstalling the filter Cleaning and Replacing the FilterPull out the power cord from the wall outlet Clean the filterAction to be taken upon warning indications About warning indicatorsPlease follow the procedures below Memo DLA-SX21U/DLA-SX21E DLA-SX21SU/DLA-SX21SE Propos de la bržlure du dispositif D-ILA Propos du choix de lÕemplacementInformation FCC Etats-Unis uniquement Information SUR LE Bruit Machine Allemagne uniquementyCordon d’alimentation Importantes mesures de sécuritéConsultez votre revendeur Ne dŽbranchez pas la fiche principale de cet appareil Remplacement du fusibleEntretien Quelques précautions d’utilisationImage rŽmanente Lieu de la projection luminositŽ de la piceContenu de l’emballage Accessoires en OptionTable des matières Signaux de l’ordinateur Support de signalRaccordement Signaux vidéoHor Pixels Ver Lines KHz PC98 Raccordement Tableau des signaux d’entrée réglables Mise sous tension Fonctionnement de baseOpérations de base RemarqueMise au point Focus pour DLA-SX21U/DLA-SX21E Fonctionnement de base Touches directes Réglage du zoom taille de l’image pour DLA-SX21U/ DLA-SX21EMise hors tension Réglage du volumeMenu principal Réglage et configuration dans les menusArborescence et structure de menus Entrée VidéoTemp.couleur menu de réglage Réglage et configuration dans les menusEntrée PC RemarqueAucun signal d’iamge Lampe de projection et temps d’utilisation Remplacement de la lampeProcédure de remplacement Remplacement de la lampeRemettez le couvercle de la lampe et serrez les vis Remplacement de la lampeRetirez le module lampe Insérez le nouveau module lampe jusqu’au fondAppui pendant Réinitialisation du compteur de la lampePrécaution pour la réinitialisation On Le tŽmoin Stand by sÕallumeRetirez le panneau du filtre Nettoyage et remplacement du filtreRéinstallez le couvercle du filtre Débranchez la prise d’alimentationTémoin Désignation Indication des témoins d’alerteAvertissement par indication des témoins Action à prendre en cas d’avertissementDLA-SX21SU/DLADLA-SX21U/DLA --SX21E SX21SE