JVC DLA-SX21SU, DLA-SX21SE, DLA-SX21E Basic Operations, Basic Operation Procedures, Power On

Page 9

Light on

Basic Operations

If projector set up is not yet complete, please read ‘Adjustments and Settings Using Menus’ on page 32 and perform the necessary settings.

STAND BY

LAMP TEMP OPERATE

PC VIDEO	1-2
	2
V-KEYSTONE H-KEYSTONE VOL.

MENUEXIT

Basic Operation Procedures

Once the basic settings are done, follow the procedures below:

1. Power On

1 The STAND BY indicator lights up when the power cord is connected.

STAND BY

LAMP TEMP OPERATE

Projector: Indicator part

2Press the OPERATE button on the projector (or the OPER- ATE button on the remote control unit) for one second or more.

The OPERATE indicator lights up and the projected image slowly appears.

ENTER

1-2

OPERATE

	OPERATE
Projector:	Remote control
Control panel	unit

Light on

STAND BY

LAMP TEMP OPERATE

Projector : Indicator

PC	VIDEO		OPERATE	2
PC	VIDEO			2
		W
V-KEYSTONE H-KEYSTONE		SCREEN	DIGITAL
V-KEYSTONE H-KEYSTONE		SCREEN	ZOOM
		S
			FREEZE
VOLUME	FOCUS	QUICK ALIGN.
MENU			EXIT
	ENTER
PRESET			HIDE

Note

•Messages are displayed in the language set by the user in the “Language” menu. The pre- set language upon purchase is “English”. The user can choose from 8 national languages. (☞ page 39)

However, the input mode (PC 1, PC 2, PC 3, Y/C, VIDEO) and button indications (FREEZE, D.ZOOM, EXIT) are only displayed in English irrespective of the display language setting.

Notes

• Upon projection, the image may flicker for a few seconds, but this is not a malfunction.

• When the lamp is turned on, it will slowly become brighter. It will take more than a minute for the brightness to stabilize.

2. Selecting the image to be projected

Press VIDEO to select which of the image devices (of those connected to the VIDEO IN (VIDEO or Y/C) terminals) is out-

put.	VIDEO
	VIDEO
VIDEO
Projector:	Remote Control
Control panel	Unit

Each time you press either button, the selected input changes as follows.

VIDEO : Image from the input VIDEO ter- minal on the right hand side of pro- jector will be projected.

Y/C : Image from the input Y/C terminal on the right hand side of the pro- jector will be projected.

ENGLISH

25

Image 9

Contents DLA-SX21U/DLA-SX21E Machine Noise Information Germany only FCC Information U.S.A. onlyDo not allow any unqualified person to install the unit Safety PrecautionHow To Replace The Fuse Wire which is coloured green-and-yellow must be conBrown Live Do not cut off the main plug from this equipmentAbout burning-in of the D-ILA device Using the screen mode switch functionViewing conditions CareAccessories ContentsSignals that can be input into the projector Connecting to Various Devices Video signals Computer signals Allowable input signals Connecting to Various DevicesSignal HorPixels Ver Lines KHzPower On Basic Operation ProceduresBasic Operations Selecting the image to be projectedAdjusting the Focus Ring Focus for DLA-SX21U/DLA- SX21E Display using the direct buttonsBasic Operations Screen displayAdjusting the Sound Volume Power OffMenu Structure Adjustments and Settings Using MenusVideo Input selection Main menuWhen PC input is selected When no image signal is inputted Adjustments and Settings Using MenusMain Set up menu Displayed only when PC is selected SubmenuAbout lamp replacement Procedure for lamp replacementReplacing the Lamp Light source lamp and its lamp timeRemove the lamp unit Replacing the LampInsert the new lamp unit until it is fully Close the handle, and tighten the screwBy mode Resetting the lamp timePress the EXIT, HIDE, Preset buttons on the remote To ensure the lamp time has been resetPull out the power cord from the wall outlet Cleaning and Replacing the FilterClean the filter Reinstalling the filterAbout warning indicators Please follow the procedures belowAction to be taken upon warning indications Memo DLA-SX21U/DLA-SX21E DLA-SX21SU/DLA-SX21SE Information FCC Etats-Unis uniquement Propos du choix de lÕemplacementInformation SUR LE Bruit Machine Allemagne uniquementy Propos de la bržlure du dispositif D-ILAImportantes mesures de sécurité Consultez votre revendeurCordon d’alimentation Ne dŽbranchez pas la fiche principale de cet appareil Remplacement du fusibleImage rŽmanente Quelques précautions d’utilisationLieu de la projection luminositŽ de la pice EntretienAccessoires en Option Table des matièresContenu de l’emballage Raccordement Support de signal Signaux vidéo Signaux de l’ordinateurRaccordement Tableau des signaux d’entrée réglablesHor Pixels Ver Lines KHz PC98 Opérations de base Fonctionnement de baseRemarque Mise sous tension Touches directes Fonctionnement de baseRéglage du zoom taille de l’image pour DLA-SX21U/ DLA-SX21E Mise au point Focus pour DLA-SX21U/DLA-SX21EMise hors tension Réglage du volumeArborescence et structure de menus Réglage et configuration dans les menusEntrée Vidéo Menu principalEntrée PC Réglage et configuration dans les menusRemarque Temp.couleur menu de réglageAucun signal d’iamge Procédure de remplacement Remplacement de la lampeRemplacement de la lampe Lampe de projection et temps d’utilisationRetirez le module lampe Remplacement de la lampeInsérez le nouveau module lampe jusqu’au fond Remettez le couvercle de la lampe et serrez les visPrécaution pour la réinitialisation Réinitialisation du compteur de la lampeOn Le tŽmoin Stand by sÕallume Appui pendantRéinstallez le couvercle du filtre Nettoyage et remplacement du filtreDébranchez la prise d’alimentation Retirez le panneau du filtreAvertissement par indication des témoins Indication des témoins d’alerteAction à prendre en cas d’avertissement Témoin DésignationDLA-SX21SU/DLADLA-SX21U/DLA --SX21E SX21SE