JVC DLA-SX21SE Replacing the Lamp, Remove the lamp unit, Close the handle, and tighten the screw

Page 16

Replacing the Lamp

3. Remove the lamp unit.

Lamp unit

4. Insert the new lamp unit until it is fully in.

Caution

• Neither touch the glass surface of the lamp directly with your hand nor stain it. If you touch it with a bare hand, oil or other substances on your hand may ad- here to the lamp, possibly preventing it from perform- ing as specified and therefore lead to a shortened lamp life, a darkened screen, etc.

5. Close the handle, and tighten the screw.

Tighten the two screws with a ª screwdriver.

6. Attach the light-source lamp cover and tighten the screw.

Tighten the two screws with a ª screwdriver.

Note

• When closing the lamp cover, please insert the left side (with the two claws) in first and then ensure that the protruding part found on the reverse side of the cover fits snugly into the hole of the main unit. As this protrusion acts as a switch, misfitting leads to power not being able to flow in.

Image 16

Contents DLA-SX21U/DLA-SX21E FCC Information U.S.A. only Machine Noise Information Germany onlySafety Precaution Do not allow any unqualified person to install the unitWire which is coloured green-and-yellow must be con How To Replace The FuseBrown Live Do not cut off the main plug from this equipmentUsing the screen mode switch function About burning-in of the D-ILA deviceViewing conditions CareContents AccessoriesConnecting to Various Devices Signals that can be input into the projector Video signals Computer signalsConnecting to Various Devices Allowable input signalsSignal HorPixels Ver Lines KHzBasic Operation Procedures Power OnBasic Operations Selecting the image to be projected Display using the direct buttons Adjusting the Focus Ring Focus for DLA-SX21U/DLA- SX21EBasic Operations Screen displayPower Off Adjusting the Sound VolumeAdjustments and Settings Using Menus Menu StructureVideo Input selection Main menuWhen PC input is selected Adjustments and Settings Using Menus When no image signal is inputtedMain Set up menu Displayed only when PC is selected SubmenuProcedure for lamp replacement About lamp replacementReplacing the Lamp Light source lamp and its lamp timeReplacing the Lamp Remove the lamp unitInsert the new lamp unit until it is fully Close the handle, and tighten the screwResetting the lamp time By modePress the EXIT, HIDE, Preset buttons on the remote To ensure the lamp time has been resetCleaning and Replacing the Filter Pull out the power cord from the wall outletClean the filter Reinstalling the filterPlease follow the procedures below About warning indicatorsAction to be taken upon warning indications Memo DLA-SX21U/DLA-SX21E DLA-SX21SU/DLA-SX21SE Propos du choix de lÕemplacement Information FCC Etats-Unis uniquementInformation SUR LE Bruit Machine Allemagne uniquementy Propos de la bržlure du dispositif D-ILAConsultez votre revendeur Importantes mesures de sécuritéCordon d’alimentation Remplacement du fusible Ne dŽbranchez pas la fiche principale de cet appareilQuelques précautions d’utilisation Image rŽmanenteLieu de la projection luminositŽ de la pice EntretienTable des matières Accessoires en OptionContenu de l’emballage Support de signal Raccordement Signaux vidéo Signaux de l’ordinateur Tableau des signaux d’entrée réglables RaccordementHor Pixels Ver Lines KHz PC98 Fonctionnement de base Opérations de baseRemarque Mise sous tensionFonctionnement de base Touches directesRéglage du zoom taille de l’image pour DLA-SX21U/ DLA-SX21E Mise au point Focus pour DLA-SX21U/DLA-SX21ERéglage du volume Mise hors tensionRéglage et configuration dans les menus Arborescence et structure de menusEntrée Vidéo Menu principalRéglage et configuration dans les menus Entrée PCRemarque Temp.couleur menu de réglageAucun signal d’iamge Remplacement de la lampe Procédure de remplacementRemplacement de la lampe Lampe de projection et temps d’utilisationRemplacement de la lampe Retirez le module lampeInsérez le nouveau module lampe jusqu’au fond Remettez le couvercle de la lampe et serrez les visRéinitialisation du compteur de la lampe Précaution pour la réinitialisationOn Le tŽmoin Stand by sÕallume Appui pendantNettoyage et remplacement du filtre Réinstallez le couvercle du filtreDébranchez la prise d’alimentation Retirez le panneau du filtreIndication des témoins d’alerte Avertissement par indication des témoinsAction à prendre en cas d’avertissement Témoin DésignationDLA-SX21SU/DLADLA-SX21U/DLA --SX21E SX21SE