Texas Instruments TMS320DM36X manual Packet Receive Operation, Receive DMA Host Configuration

Page 44

Architecture

www.ti.com

2.11 Packet Receive Operation

2.11.1Receive DMA Host Configuration

To configure the receive DMA for operation the host must:

•Initialize the receive addresses.

•Initialize the receive channel n DMA head descriptor pointer registers (RXnHDP) to 0.

•Write the MAC address hash n registers (MACHASH1 and MACHASH2), if hash matching multicast addressing is desired.

•If flow control is to be enabled, initialize:

–the receive channel n free buffer count registers (RXnFREEBUFFER)

–the receive channel n flow control threshold register (RXnFLOWTHRESH)

–the receive filter low priority frame threshold register (RXFILTERLOWTHRESH)

•Enable the desired receive interrupts using the receive interrupt mask set register (RXINTMASKSET) and the receive interrupt mask clear register (RXINTMASKCLEAR).

•Set the appropriate configuration bits in the MAC control register (MACCONTROL).

•Write the receive buffer offset register (RXBUFFEROFFSET) value (typically zero).

•Setup the receive channel(s) buffer descriptors and initialize RXnHDP.

•Enable the receive DMA controller by setting the RXEN bit in the receive control register (RXCONTROL).

•Configure and enable the receive operation, as desired, in the receive multicast/broadcast/promiscuous channel enable register (RXMBPENABLE) and by using the receive unicast set register (RXUNICASTSET) and the receive unicast clear register (RXUNICASTCLEAR).

2.11.2Receive Channel Enabling

Each of the eight receive channels has an enable bit (RXCHnEN) in the receive unicast enable set register (RXUNICASTSET) that is controlled using RXUNICASTSET and the receive unicast clear register (RXUNICASTCLEAR). The RXCHnEN bits determine whether the given channel is enabled (set to 1) to receive frames with a matching unicast or multicast destination address.

The RXBROADEN bit in the receive multicast/broadcast/promiscuous channel enable register (RXMBPENABLE) determines if broadcast frames are enabled or filtered. If broadcast frames are enabled, then they are copied to only a single channel selected by the RXBROADCH field in

RXMBPENABLE.

The RXMULTEN bit in RXMBPENABLE determines if hash matching multicast frames are enabled or filtered. Incoming multicast addresses (group addresses) are hashed into an index in the hash table. If the indexed bit is set, the frame hash will match and it will be transferred to the channel selected by the RXMULTCH field in RXMBPENABLE when multicast frames are enabled. The multicast hash bits are set in the MAC address hash n registers (MACHASH1 and MACHASH2).

The RXPROMCH bits in RXMBPENABLE select the promiscuous channel to receive frames selected by the RXCMFEN, RXCSFEN, RXCEFEN, and RXCAFEN bits. These four bits allow reception of MAC control frames, short frames, error frames, and all frames (promiscuous), respectively.

The address RAM can be configured to set multiple unicast and/or multicast addresses to a given channel (if the match bit is set in the RAM). Multicast addresses in the RAM are enabled by RXUNICASTSET and not by the RXMULTEN bit in RXMBPENABLE, the RXMULTEN bit enables the hash multicast match only. The address RAM takes precedence over the hash match.

If a multicast packet is received that hash matches (multicast packets enabled), but is filtered in the RAM, then the packet is filtered. If a multicast packet does not hash match, regardless of whether or not hash matching is enabled, but matches an enabled multicast address in the RAM, then the packet will be transferred to the associated channel.

44 Ethernet Media Access Controller (EMAC)/Management Data Input/Output SPRUFI5B –March 2009 –Revised December 2010

(MDIO)

Submit Documentation Feedback

 

© 2009–2010, Texas Instruments Incorporated

Page 43 Page 45
Image 44
Page 43 Page 45
Contents Users Guide Submit Documentation Feedback Mdio Registers Mdio Version Register Version Mdio Control Register Control Appendix a Appendix BList of Figures Transmit Interrupt Mask Set Register Txintmaskset List of Tables MAC Control Register Maccontrol Field Descriptions Read This First Related Documentation From Texas Instruments Related Documentation From Texas Instruments Features Purpose of the PeripheralFunctional Block Diagram Emac and Mdio Block DiagramMII Clocking Industry Standards Compliance StatementClock Control Media Independent Interface MII Connections Signal DescriptionsMemory Map Pin Multiplexing Emac and Mdio Signals for MII InterfaceSignal Type Description Ethernet Protocol Overview Ethernet Frame FormatEthernet Frame Description Field Bytes DescriptionEthernet’s Multiple Access Protocol Programming InterfacePacket Buffer Descriptors WordBasic Descriptor Description Field Field DescriptionTransmit and Receive Descriptor Queues Transmit and Receive Emac Interrupts Transmit Buffer Descriptor Format Example 1. Transmit Buffer Descriptor in C Structure FormatNext Descriptor Pointer Buffer PointerBuffer Offset Buffer LengthEnd of Packet EOP Flag Ownership Owner FlagEnd of Queue EOQ Flag Teardown Complete Tdowncmplt FlagReceive Buffer Descriptor Format Receive Buffer Descriptor FormatExample 2. Receive Buffer Descriptor in C Structure Format Buffer Length Code Error Codeerror Flag Alignment Error Alignerror FlagCRC Error Crcerror Flag Jabber FlagEmac Control Module Internal MemoryBus Arbiter CPUReceive Pulse Interrupt Interrupt ControlTransmit Pulse Interrupt Interrupt Pacing Receive Threshold Pulse InterruptMiscellaneous Pulse Interrupt Mdio Module Mdio Module ComponentsMdio Clock Generator Global PHY Detection and Link State MonitoringMdio Module Operational Overview PHY Register User AccessActive PHY Monitoring Reading Data From a PHY Register Initializing the Mdio ModuleWriting Data To a PHY Register Example of Mdio Register Access Code Example 3. Mdio Register Access MacrosEmac Module Emac Module ComponentsReceive DMA Engine Receive FifoClock and Reset Logic MAC ReceiverReceive Address Transmit DMA EngineEmac Module Operational Overview Media Independent Interface MII Data ReceptionReceive Control Receive Inter-Frame IntervalCollision-Based Receive Buffer Flow Control Ieee 802.3x-Based Receive Buffer Flow ControlTransmit Control CRC InsertionAdaptive Performance Optimization APO Interpacket-Gap IPG EnforcementTransmit Flow Control Speed, Duplex, and Pause Frame SupportReceive Channel Enabling Receive DMA Host ConfigurationPacket Receive Operation Receive Address Matching Hardware Receive QOS SupportReceive Frame Classification Host Free Buffer TrackingReceive Channel Teardown Receive Frame Treatment Promiscuous Receive ModeReceive Frame Treatment Summary Middle of Frame Overrun Treatment Receive OverrunMiddle of Frame Overrun Treatment Transmit DMA Host Configuration Packet Transmit OperationReceive and Transmit Latency Transmit Channel TeardownTransfer Node Priority Reset ConsiderationsSoftware Reset Considerations Hardware Reset Considerations InitializationEnabling the EMAC/MDIO Peripheral Emac Control Module InitializationExample 4. Emac Control Module Initialization Code Mdio Module Initialization Example 5. Mdio Module Initialization CodeEmac Module Initialization Interrupt Support Emac Module Interrupt Events and RequestsReceive Threshold Interrupts Transmit Packet Completion InterruptsReceive Packet Completion Interrupts Host Error Interrupt Statistics InterruptUser Access Completion Interrupt Mdio Module Interrupt Events and RequestsLink Change Interrupt Proper Interrupt ProcessingPower Management Emulation ConsiderationsEmulation Control Soft Free DescriptionEmac Control Module Registers Slave VbusAcronym Register Description Bit Field Value DescriptionEmac Control Module Software Reset Register Cmsoftreset SoftresetEmac Control Module Emulation Control Register Cmemcontrol Soft FreeIntprescale Emac Control Module Interrupt Control Register CmintctrlIntpaceen Rxthreshen RxpulseenTxpulseen Statpendinten Statpendinten Hostpendinten Linkinten UserintenBit Field Rxthreshinttstat RxpulseinttstatTxpulseinttstat 31-8 Reserved TXPULSEINTTSTATnStatpendintstat Hostpendintstat Linkintstat Userintstat StatpendintstatRximax TximaxMdio Version Register Version Field Descriptions Mdio Version Register VersionManagement Data Input/Output Mdio Registers Mdio Control Register Control Mdio Control Register Control Field DescriptionsPHY Acknowledge Status Register Alive PHY Link Status Register LinkPHY Acknowledge Status Register Alive Field Descriptions PHY Link Status Register Link Field Descriptions31-2 Reserved Will clear the event and writing a 0 has no effect No Mdio user command complete event USERINTMASKED0 and USERINTMASKED1 correspond to USERACCESS0 W1S-0 Mdio User Command Complete Interrupt Mask Clear Register Mdio User Command Complete Interrupt Mask Clear RegisterMdio User Access Register 0 USERACCESS0 Mdio User Access Register 0 USERACCESS0 Field DescriptionsMdio User PHY Select Register 0 USERPHYSEL0 Linksel LinkintenbPhyadrmon LinkselMdio User Access Register 1 USERACCESS1 Mdio User Access Register 1 USERACCESS1 Field DescriptionsMdio User PHY Select Register 1 USERPHYSEL1 Mdio User PHY Select Register 1 USERPHYSEL1Ethernet Media Access Controller Emac Registers Offset Acronym Register Description Network Statistics Registers Transmit Control Register Txcontrol Field Descriptions Transmit Identification and Version Register TxidverTransmit Control Register Txcontrol Txtdnch Transmit Teardown Register TxteardownTransmit Teardown Register Txteardown Field Descriptions Receive Identification and Version Register Rxidver RxidentRxmajorver Rxminorver RxmajorverReceive Control Register Rxcontrol Receive Teardown Register RxteardownReceive Control Register Rxcontrol Field Descriptions Receive Teardown Register Rxteardown Field DescriptionsTransmit Interrupt Status Unmasked Register Txintstatraw TX7PENDTransmit Interrupt Status Masked Register Txintstatmasked Transmit Interrupt Status Masked Register TxintstatmaskedTransmit Interrupt Mask Set Register Txintmaskset TX7MASKTransmit Interrupt Mask Clear Register Txintmaskclear Transmit Interrupt Mask Clear Register TxintmaskclearMAC Input Vector Register Macinvector MAC End Of Interrupt Vector Register MaceoivectorMAC Input Vector Register Macinvector Field Descriptions StatpendReceive Interrupt Status Unmasked Register Rxintstatraw RX7PENDReceive Interrupt Status Masked Register Rxintstatmasked Receive Interrupt Status Masked Register RxintstatmaskedReceive Interrupt Mask Set Register Rxintmaskset RX7MASKReceive Interrupt Mask Clear Register Rxintmaskclear Receive Interrupt Mask Clear Register RxintmaskclearHostpend Statpend MAC Interrupt Status Unmasked Register MacintstatrawMAC Interrupt Status Masked Register Macintstatmasked MAC Interrupt Mask Set Register Macintmaskset MAC Interrupt Mask Clear Register MacintmaskclearHostmask Statmask HostmaskRxpasscrc Rxqosen Rxnochain RxcmfenRxcsfen Rxcefen Rxcafen RxpromchFrames containing errors are filtered Receive multicast channel select Receive Unicast Enable Set Register Rxunicastset RXCH7ENReceive Unicast Clear Register Rxunicastclear Receive Unicast Clear Register RxunicastclearReceive Maximum Length Register Rxmaxlen Field Descriptions Receive Maximum Length Register RxmaxlenReceive Buffer Offset Register Rxbufferoffset Rxfilterthresh Receive Channel 0-7 Free Buffer Count Register RXnFREEBUFFER MAC Control Register Maccontrol MAC Control Register Maccontrol Field DescriptionsTxflowen RxbufferflowenLoopback FullduplexMAC Status Register Macstatus MAC Status Register Macstatus Field DescriptionsRxqosact Emulation Control Register Emcontrol Fifo Control Register FifocontrolEmulation Control Register Emcontrol Field Descriptions Fifo Control Register Fifocontrol Field DescriptionsMAC Configuration Register Macconfig Soft Reset Register SoftresetMAC Configuration Register Macconfig Field Descriptions Soft Reset Register Softreset Field DescriptionsMAC Source Address Low Bytes Register Macsrcaddrlo MAC Source Address High Bytes Register MacsrcaddrhiMAC Hash Address Register 1 MACHASH1 MAC Hash Address Register 2 MACHASH2MAC Hash Address Register 1 MACHASH1 Field Descriptions MAC Hash Address Register 2 MACHASH2 Field DescriptionsBack Off Test Register Bofftest Field Descriptions Back Off Test Register BofftestTransmit Pacing Algorithm Test Register Tpacetest Receive Pause Timer Register Rxpause Transmit Pause Timer Register TxpauseReceive Pause Timer Register Rxpause Field Descriptions Transmit Pause Timer Register Txpause Field DescriptionsMAC Address Low Bytes Register Macaddrlo MAC Address Low Bytes Register Macaddrlo Field DescriptionsValid Matchfilt Channel MACADDR0 MACADDR1 ValidMAC Address High Bytes Register Macaddrhi MAC Index Register MacindexMAC Index Register Macindex Field Descriptions MACADDR2 MACADDR3 MACADDR4 MACADDR5TXnHDP Transmit Channel 0-7 Completion Pointer Register TXnCP Receive Channel 0-7 Completion Pointer Register RXnCPNetwork Statistics Registers Good Receive Frames Register RxgoodframesBroadcast Receive Frames Register Rxbcastframes Multicast Receive Frames Register RxmcastframesReceive CRC Errors Register Rxcrcerrors Receive Alignment/Code Errors Register RxaligncodeerrorsPause Receive Frames Register Rxpauseframes Receive Oversized Frames Register RxoversizedReceive Jabber Frames Register Rxjabber Receive Undersized Frames Register RxundersizedReceive Frame Fragments Register Rxfragments Filtered Receive Frames Register RxfilteredReceive QOS Filtered Frames Register Rxqosfiltered Receive Octet Frames Register RxoctetsGood Transmit Frames Register Txgoodframes Broadcast Transmit Frames Register TxbcastframesPause Transmit Frames Register Txpauseframes Deferred Transmit Frames Register TxdeferredTransmit Collision Frames Register Txcollision Transmit Single Collision Frames Register TxsinglecollTransmit Underrun Error Register Txunderrun Transmit Carrier Sense Errors Register TxcarriersenseTransmit Late Collision Frames Register Txlatecoll Transmit Octet Frames Register TxoctetsSubmit Documentation Feedback Network Octet Frames Register Netoctets Receive DMA Overruns Register RxdmaoverrunsAppendix a Glossary Physical Layer Definitions Term DefinitionDocument Revision History Reference Additions/Modifications/DeletionsRfid Products ApplicationsDSP
Related manuals
Manual 18 pages 38.41 Kb
Top Page Image Contents