Sharp UX-A260 manual Override Ringing, Programming the override code, Answering, Machine

Page 37

Override Ringing

Override Ringing

6 Each time the machine receives an incoming message, it will call your

programmed transfer number. When you answer, you will hear your recorded message telling you that the call is a transfer call. On the dial

pad of your phone, enter , your remote code number (see page 37),

and . The machine will play back your messages.

•You can also perform any of the remote operations described in Remote Operations later in this chapter (see page 37).

Note: When you hang up after a transfer call, the machine will not immediately resume normal operation. If you want the machine to accept calls

immediately after a transfer call, enter twice before hanging up (if you

want to hang up during message playback, first enter 0 and

to stop

playback, then enter twice).

Answering	Machine
2.

Override Ringing

This function allows selected callers using a touch-tone telephone to override the answering system's outgoing message and cause the machine to make a special ringing sound, alerting you that they are calling. This is useful when you are near the machine but only want to talk with certain callers, taking all other calls on the answering system.

Programming the override code

To override the answering system, your callers must enter a 3-digit override code from their telephone. This code has been set to "009" at the factory. If you wish to change the code, press the panel keys as shown below.

Important! Make sure the override code is different from the remote code used for remote operations.

1 Press FUNCTION once and	Display:
	once.

T.A.D. SETTING

35

Image 37

Contents FACSIMILE UX-A260MODEL OPERATION MANUALModel Number UX-A260 Serial Number Date of Purchase Place of Purchase FOR YOUR RECORDSABOUT THE TELEPHONE CONSUMER PROTECTION ACT OF Introduction Display Important safety information 1. Installation Table of Contents2. Using the Answering System Unpacking Checklist Connections Loading the Imaging FilmTroubleshooting MaintenanceProblems and Solutions Messages and Signals Clearing Paper Jams 6. Special Functions2 RESOLUTION / RECEPTION MODE key A Look at the Operation Panel1 SPEAKER key 3 FLASH key8 Number keys 7 UP and DOWN arrow keys9 Panel release 10 STOP keyPress this key while listening to a message to play it again page REPEAT keySKIP key 18 DELETE keyUnpacking Checklist 1. InstallationPoints to keep in mind when setting up 1. InstallationConnecting the power cord Connecting the handsetConnections OPTION SETTING Connecting the telephone line cordDisplay DIAL MODEComments Attach the paper tray and paper tray extensionLoading the Imaging Film Loading the Imaging Film4 Remove the new roll of imaging film from its packaging Loading Printing Paper Loading Printing PaperGENTLY LOAD PAPER INTO THE PAPER TRAY DO NOT FORCE IT DOWN INTO THE FEED SLOTPrint contrast setting Setting the paper sizeSTART/MEMORYFUNCTION Entering Your Name and Fax NumberENTRY MODE OWN NUMBER SETDisplay DATE&TIME SET Installation1 Setting the Date and TimeSetting the Date and Time Daylight Saving Time Setting the reception mode Setting the Reception ModeMake sure a document is not loaded in the document feeder, and then Speaker Volume AdjustmentRinger HandsetRecording an Outgoing Message 2. Using the Answering SystemTo listen to the outgoing message Operating the Answering SystemActivating the answering system AnsweringToll Saver ON Number of rings in TAD mode Toll Saver functionToll Saver OFF 1 Press PLAY/HOLD Listening to received messages2 The messages will play Recording memos Erasing received messagesRecording phone conversations 2-way recording Setting ICM time Optional Answering System SettingsFAX mode on TAD failure The display briefly shows your selection, then OGM only modeCPC Detection Programming the transfer number Transfer FunctionOGM2TRANSFER Recording the transfer messageTurning the Transfer function on and off Checking or erasing the transfer messageProgramming the override code Override RingingOverriding the answering system Remote code number Remote OperationsToll Saver Retrieving your messages Erase all messages Press 3 While the messages are playing, you can do any of the followingRepeat playback Press Changing the fax reception mode Other remote operationsTurning the Transfer function on or off Recording a new outgoing messageChanging the transfer telephone number Recording a Memo Recording a new transfer messageIf the machine detects silence, it will stop recording automatically 3. Sending Faxes Size and weightTransmittable Documents Sending FaxesOther restrictions Loading the DocumentResolution settings Adjusting the Resolution and ContrastSending FaxesLoad the documents Contrast settingsPress RECEPTION MODE one or more times Sending a Fax by Normal Dialing Sending a Fax by Normal DialingStoring fax and phone numbers for automatic dialing Sending a Fax by Automatic Dialing4 Press START/MEMORY Editing and clearing auto-dial numbers EDIT 4 Select EDIT or CLEARCLEAR 5 If you selected EDIT, make the desired changes to the numberDialing an auto-dial number with the SPEED key If desired, press RECEPTION MODE to set the Searching for an auto-dial numberREADY TO SEND to backspace and clear one digit Sending a fax by Direct Keypad DialingAutomatic redialing Redialto set the Error Correction Mode Broadcasting sending a fax to multiple destinations Sending a Fax From MemoryIf the memory becomes full Memory transmission4. Receiving Faxes Using FAX ModeChanging the number of rings ReceivingUsing TEL Mode Using TEL ModeAnswering on an extension phone connected to the same line Answering with the fax’s handsetPutting a call on hold Fax Signal Receive Optional Reception SettingsReception Ratio Substitute Reception to Memory Substitute Reception to Memory5. Making Copies 5. Making CopiesMaking Copies Copy Cut-off6. Special Functions Caller ID Requires Subscription to Service6. Special Functions Display messages How Caller ID operatesCaller ID Requires Subscription to Service Viewing the Caller ID list Priority Call To delete calls from the Caller ID listOWN NUMBER SET Blocking voice calls Distinctive Ring Requires Subscription to Service Distinctive Ring Requires Subscription to ServiceBlocking Reception of Unwanted Faxes Blocking Reception of Unwanted FaxesPolling Requesting a Fax Transmission Printing 7. Printing ListsLists LISTING MODETelephone Number List Setup ListMessage List Caller-ID ListHeadings in Transaction Report Transaction ReportSENDER RECEIVERTransaction Report print condition 8. Maintenance 8. MaintenancePrint head Maintenance Scanning glass and rollersThe housing Problems and Solutions 9. TroubleshootingLine error 9. Trouble- shooting Dialing and transmission problemsProblems and Solutions Make sure the operation panel is completely closed Reception and copying problemsSee Loading the Imaging Film in Chapter General problemsTransmittable Documents on page Messages and Signals Messages and Signalsusing it to dial and send a fax. Replace the handset or problem so that printing can continue see SubstituteReception to Memory on page the memory becomes full on pageAudible signals Clearing a jammed document Clearing Paper JamsClearing jammed printing paper Part distribution centers Ordering PartsFCC Regulatory Information FCC Regulatory InformationS H A R P MATERIAL SAFETY DATA SHEET 1/2MATERIAL SAFETY DATA SHEET 2/2 Sending Faxes Quick Reference GuideRecording an OGM Receiving FaxesTransmisión de mensajes telefax Guía de referencia rápidaGrabacion de un mensaje de bienvenida Recepción de mensajes telefaxIndex Index Page Page Page Page Remote Operation Guide REMOTE OPERATION CARDREMOTE COMMANDS SHARP ELECTRONICS CORPORATION LIMITED WARRANTYSHARP ELECTRONICS CORPORATION SHARP CORPORATIONSharp Plaza, Mahwah, New Jersey