Rugged Outback ELX4-60 manual Using Relay, Using Screen Lock, Playback via various mode

Page 16

ELX4 -60

BASIC CONFIGURATION

3.8. Using Relay

-To set relay on/off. (ELX4 -60 supports four relay outputs.)

-Press the [SEARCH/RELAY] button.

-The icon of “Relay On” shows.

-Press the relay number button between 1 and 4, and then the related relay out signal will be transmitted.

-In order to set relay off, press the [SEARCH/RELAY] button again.

-Then “Relay On ” shows because relay keeps being set as on.

- Press the [SEARCH/RELAY] button again, and then the icon of “Relay Off” will show. - Press the relay a number button to set off.

3.9. Using Screen Lock

-To set screen lock.

-For this function, user password should be set at first.

-If pressing the [EXIT/LOCK] button for 2~3 seconds, lock mode will run with showing “Screen Locked” message.

-If lock mode runs, any function button will not be operated.

-In order to cancel lock mode, user password should be entered.

4. Playback

To replay recorded images in full screen or quad split screen modes.

4.1. Playback via various mode

4.1.1. Playback via basic screen (full screen)

-Press the Play [ ] button during monitoring mode.

-Play [ ] button will begin playback of the last 1minut e, 45 seconds of recorded video at 1X speed.

<Note>

When pressing the play button in multi-monitoring mode, channel 1 is always the channel displayed. More specifically, images recorded on Channel 1 during the last 30 seconds are always displayed. However pressing the playback button in single-channel monitoring mode, will display the selected channel. To display another channel, press the corresponding number button on the front of ELX4-60.

16

2003.05.21 (v 1.0)

Rugged CCTV

Image 16

Contents ELX4-60 User’s Guide Cctv Monitor UserFCC Compliance Statement Important Notice ELX4 Rugged CctvSetting at Text menu Setting at Serial Setup’s RS232 menu Appendix #2 Utilizing IP Addresses on Local Network What is ELX4-60? IntroductionKey features ELX4-60Product Description Front PanelRear Panel DIOInstallation Summary Monitoring Viewing basic screen Quad-splitViewing single full screen Viewing multi screen Viewing all channels with sequence mode Viewing images with Digital Zoom Viewing an alarm triggered channelViewing with connected PTZ Load Preset Save PresetPan/Tilt Control Zoom/Focus ControlUsing Relay Using Screen LockPlayback via various mode PlaybackPlayback with Digital Zoom Playback via split screenVarious playback modes Using Search Mode Button controlCopy / Backup / Delete Data Manager Copy ImageSeconds Select DiskBackup Manager Start Date & Time / End Date & TimeConfiguration Quick SetupDelete Data Date/TimeTime Zone Daylight SavingTime Format Date/TimeRecording Configuration Status Channel StatusRecording Speed/Quality Audio RecordingCamera Analog Camera Channels Ch ~ Ch NameTIP Status TypeColor Gain/Brightness/ContrastNormal Rec. Analog Camera Channels Ch ~ Ch Time ScheduleSetting Time Schedule Weekday Start/EndDay Start/End Special Time RecordingSetting Special Time Event RecordingMD Area Alarm Rec. Analog Camera Channels Ch ~ ChSensor 1/2/3/4 Pre Alarm sec Setting MD AreaText Post Alarm sec Relay SetupSpecial Time Alarm Pop-up/Pop-up Holdsec Seq. SwitchingsecMonitor System AudioText Recording / MonitoringSync Text With DeviceTimeout ms Seek HeaderDelimiter LinesTime Schedule To designate Weekday/Weekend and Day/NightSpecial Time User Password Admin PasswordRemote Setup SecurityDisk Setup Auto Del. AlarmBackup Reminder Auto Del. NormalNetwork NetworkIP Address, NetMask, and Gateway Address DNS Server IP AddressUser ID/Password XDSLHRS HRS IntervalGroup ID TP Server Port Monitoring Port / Playback PortFirewall / Port Interface Serial SetupBaud rate/Parity/Stop bit/Data bit How to register remote controller Remote Control IDMiscellaneous Alarm Buzzer Reset ValuesKeyboard Control Addr Keyboard PTZ AddrUtility Disk Manager Type Using IP Cam Activating IP Cam menusCamera Setting IP Camera Channels Ch ~ Ch ConfigurationPort IP AddressURLBand Width LimitKB/s Search Local IP Cam ListSelect Cam Normal Rec. IP Camera Channels Ch ~ Ch Recording Speed/Quality & Pre Alarm & Post Alarm Alarm Rec. IP Cam Channel Ch ~ ChIP Cam Event Using Text Device Connecting External DeviceSetting at Text menu Setting at Serial Setup’s RS232 menu Setting at Alarm Rec. menuSetting at Normal Rec. menu Using Keyboard Setting at Serial Setup’s PTZ menuAppendix Appendix #1 Technical Specification Appendix Appendix Appendix #2 Utilizing IP Addresses on Local Network #2.1 Introduction#2.2 IP construction and Network class IP constructionNetwork configuration To use as one network Features of Addresses#2.3 C-class Network To use as two sub-networks 1/2 + 1/2 To use as three sub-networks 1/4 + 1/4 + 1/2To use as four sub-networks 1/4 + 1/4 + 1/4 + 1/4 Appendix