Rugged Outback ELX4-60 manual Configuration, Quick Setup, Delete Data, Date/Time

Page 21

BASIC CONFIGURATION

ELX4 -60

4.3.3. Delete Data

To delete a specific file range from the current recording HDD. This menu does not affect backup disk. The beginning of the range is always the beginning of the recording on the HDD.

5. Configuration

5.1. Quick Setup

There are three menus for recording setup; Quick Setup, Normal Recording, Alarm Recording menu in Configuration Menu. Quick Setup is the easiest set-up, activating all four analog cameras to record with the same settings and conditions . Normal recording is the standard recording settings and can be customized based on time and channel. Alarm recording is the recording schedule based on alarm conditions (Motion Detection, Sensors, etc.) Also, Quick Setup has time setting menu.

5.1.1. Date/Time

When ELX4-60 is manufactured in factory, time zone will be set as “GMT + 9:00 ”. Set the time to local time zone.

Changing ELX4 -60 time may cause time conflict with recorded images. In this case, it is strongly recommended to re-format the hard drives after making changes.

Button control

-Press [MENU] button on ELX4 -60 front panel.

-Move to “Quick Setup” menu (First tab on the Configuration menu).

-Move to “Date/Time” below “Quick Setup ” using downward arrow button on ELX4-60 front panel.

-Press the [ENTER] button on ELX4-60 front panel.

-Set time. (The following picture will be displayed when setting time menu)

-In order to access each menu, press [ENTER] button after selecting it with upward/downward

arrow button on ELX4-60 front panel.

Rugged CCTV

2003.05.21 (v 1.0)

21

Image 21

Contents User’s Guide Cctv Monitor User ELX4-60FCC Compliance Statement Important Notice Rugged Cctv ELX4Setting at Text menu Setting at Serial Setup’s RS232 menu Appendix #2 Utilizing IP Addresses on Local Network Introduction What is ELX4-60?ELX4-60 Key featuresFront Panel Product DescriptionDIO Rear PanelInstallation Summary Viewing basic screen Quad-split MonitoringViewing single full screen Viewing multi screenViewing all channels with sequence mode Viewing an alarm triggered channel Viewing images with Digital ZoomViewing with connected PTZ Save Preset Load PresetPan/Tilt Control Zoom/Focus ControlUsing Screen Lock Using RelayPlayback via various mode PlaybackPlayback via split screen Playback with Digital ZoomVarious playback modes Button control Using Search ModeCopy Image Copy / Backup / Delete Data ManagerSeconds Select DiskStart Date & Time / End Date & Time Backup ManagerQuick Setup ConfigurationDelete Data Date/TimeDaylight Saving Time ZoneTime Format Date/TimeRecording Channel Status Configuration StatusRecording Speed/Quality Audio RecordingName Camera Analog Camera Channels Ch ~ ChTIP Type StatusColor Gain/Brightness/ContrastTime Schedule Normal Rec. Analog Camera Channels Ch ~ ChWeekday Start/End Setting Time ScheduleDay Start/End Special Time RecordingEvent Recording Setting Special TimeAlarm Rec. Analog Camera Channels Ch ~ Ch MD AreaSensor 1/2/3/4 Setting MD Area Pre Alarm secText Post Alarm sec Setup RelaySpecial Time Seq. Switchingsec Alarm Pop-up/Pop-up HoldsecMonitor Audio SystemRecording / Monitoring TextSync Text With DeviceSeek Header Timeout msDelimiter LinesTo designate Weekday/Weekend and Day/Night Time ScheduleSpecial Time Admin Password User PasswordRemote Setup SecurityAuto Del. Alarm Disk SetupBackup Reminder Auto Del. NormalNetwork NetworkDNS Server IP Address IP Address, NetMask, and Gateway AddressXDSL User ID/PasswordHRS Interval HRSGroup ID Monitoring Port / Playback Port TP Server PortFirewall / Port Serial Setup InterfaceBaud rate/Parity/Stop bit/Data bit Remote Control ID How to register remote controllerMiscellaneous Reset Values Alarm BuzzerKeyboard Control Addr Keyboard PTZ AddrUtility Disk Manager Type Activating IP Cam menus Using IP CamConfiguration Camera Setting IP Camera Channels Ch ~ ChIP AddressURL PortBand Width LimitKB/s Local IP Cam List SearchSelect Cam Normal Rec. IP Camera Channels Ch ~ Ch Alarm Rec. IP Cam Channel Ch ~ Ch Recording Speed/Quality & Pre Alarm & Post AlarmIP Cam Event Connecting External Device Using Text DeviceSetting at Text menu Setting at Alarm Rec. menu Setting at Serial Setup’s RS232 menuSetting at Normal Rec. menu Setting at Serial Setup’s PTZ menu Using KeyboardAppendix Appendix #1 Technical Specification Appendix Appendix #2.1 Introduction Appendix #2 Utilizing IP Addresses on Local Network#2.2 IP construction and Network class IP constructionFeatures of Addresses Network configuration To use as one network#2.3 C-class Network To use as three sub-networks 1/4 + 1/4 + 1/2 To use as two sub-networks 1/2 + 1/2To use as four sub-networks 1/4 + 1/4 + 1/4 + 1/4 Appendix