Rugged Outback ELX4-60 manual System, Audio

Page 36

ELX4 -60

BASIC CONFIGURATION

5.7. System

5.7.1. Audio

ELX4-60 supports one channel audio input. This single audio channel can be replayed with any connected channel or with all of them.

Recording

Set to “On” using the [ENTER] button and the [ARROW] buttons to record audio.

Audio Gain

Increases or decreases the sensitivity to the audio signal. Can be set between –7 and +8.

+20dB

To amplify the audio input signal. Should ONLY be used when using an external microphone .

Sync Audio with

Designate which channel(s) to synchronize audio with during playback.

36

2003.05.21 (v 1.0)

Rugged CCTV

Image 36

Contents ELX4-60 User’s Guide Cctv Monitor UserFCC Compliance Statement Important Notice ELX4 Rugged CctvSetting at Text menu Setting at Serial Setup’s RS232 menu Appendix #2 Utilizing IP Addresses on Local Network What is ELX4-60? IntroductionKey features ELX4-60Product Description Front PanelRear Panel DIOInstallation Summary Monitoring Viewing basic screen Quad-splitViewing single full screen Viewing multi screenViewing all channels with sequence mode Viewing an alarm triggered channel Viewing images with Digital ZoomViewing with connected PTZ Load Preset Save PresetPan/Tilt Control Zoom/Focus ControlUsing Relay Using Screen LockPlayback via various mode PlaybackPlayback via split screen Playback with Digital ZoomVarious playback modes Using Search Mode Button controlCopy / Backup / Delete Data Manager Copy ImageSeconds Select DiskBackup Manager Start Date & Time / End Date & TimeConfiguration Quick SetupDelete Data Date/TimeTime Zone Daylight SavingTime Format Date/TimeRecording Configuration Status Channel StatusRecording Speed/Quality Audio RecordingCamera Analog Camera Channels Ch ~ Ch NameTIP Status TypeColor Gain/Brightness/ContrastNormal Rec. Analog Camera Channels Ch ~ Ch Time ScheduleSetting Time Schedule Weekday Start/EndDay Start/End Special Time RecordingSetting Special Time Event RecordingAlarm Rec. Analog Camera Channels Ch ~ Ch MD AreaSensor 1/2/3/4 Setting MD Area Pre Alarm secText Post Alarm sec Setup RelaySpecial Time Seq. Switchingsec Alarm Pop-up/Pop-up HoldsecMonitor System AudioText Recording / MonitoringSync Text With DeviceTimeout ms Seek HeaderDelimiter LinesTime Schedule To designate Weekday/Weekend and Day/NightSpecial Time User Password Admin PasswordRemote Setup SecurityDisk Setup Auto Del. AlarmBackup Reminder Auto Del. NormalNetwork NetworkIP Address, NetMask, and Gateway Address DNS Server IP AddressUser ID/Password XDSLHRS HRS IntervalGroup ID Monitoring Port / Playback Port TP Server PortFirewall / Port Serial Setup InterfaceBaud rate/Parity/Stop bit/Data bit Remote Control ID How to register remote controllerMiscellaneous Alarm Buzzer Reset ValuesKeyboard Control Addr Keyboard PTZ AddrUtility Disk Manager Type Using IP Cam Activating IP Cam menusCamera Setting IP Camera Channels Ch ~ Ch ConfigurationIP AddressURL PortBand Width LimitKB/s Local IP Cam List SearchSelect Cam Normal Rec. IP Camera Channels Ch ~ Ch Alarm Rec. IP Cam Channel Ch ~ Ch Recording Speed/Quality & Pre Alarm & Post AlarmIP Cam Event Connecting External Device Using Text DeviceSetting at Text menu Setting at Serial Setup’s RS232 menu Setting at Alarm Rec. menuSetting at Normal Rec. menu Using Keyboard Setting at Serial Setup’s PTZ menuAppendix Appendix #1 Technical Specification Appendix Appendix Appendix #2 Utilizing IP Addresses on Local Network #2.1 Introduction#2.2 IP construction and Network class IP constructionFeatures of Addresses Network configuration To use as one network#2.3 C-class Network To use as two sub-networks 1/2 + 1/2 To use as three sub-networks 1/4 + 1/4 + 1/2To use as four sub-networks 1/4 + 1/4 + 1/4 + 1/4 Appendix