Rugged Outback ELX4-60 manual Xdsl, User ID/Password

Page 45

BASIC CONFIGURATION

ELX4 -60

5.7.7.2.xDSL

If ELX4-60 is connected on xDSL line and needs PPPoE process, the network administrator should configure the user ID and password for PPPoE. ID. The password may be acquired from the ISP that installed the line. Once configured, the ELX4-60will receive an IP address when it is connected on xDSL line.

User ID/Password

When ELX4-60 is connected to xDSL, access ID and Password should be entered.

Status

Displays the ELX4 -60 connection status.

Rugged CCTV

2003.05.21 (v 1.0)

45

Image 45

Contents User’s Guide Cctv Monitor User ELX4-60FCC Compliance Statement Important Notice Rugged Cctv ELX4Setting at Text menu Setting at Serial Setup’s RS232 menu Appendix #2 Utilizing IP Addresses on Local Network Introduction What is ELX4-60?ELX4-60 Key featuresFront Panel Product DescriptionDIO Rear PanelInstallation Summary Viewing basic screen Quad-split MonitoringViewing single full screen Viewing multi screenViewing all channels with sequence mode Viewing an alarm triggered channel Viewing images with Digital ZoomViewing with connected PTZ Save Preset Load PresetPan/Tilt Control Zoom/Focus ControlUsing Screen Lock Using RelayPlayback via various mode PlaybackPlayback via split screen Playback with Digital ZoomVarious playback modes Button control Using Search ModeCopy Image Copy / Backup / Delete Data ManagerSeconds Select DiskStart Date & Time / End Date & Time Backup ManagerQuick Setup ConfigurationDelete Data Date/TimeDaylight Saving Time ZoneTime Format Date/TimeRecording Channel Status Configuration StatusRecording Speed/Quality Audio RecordingName Camera Analog Camera Channels Ch ~ ChTIP Type StatusColor Gain/Brightness/ContrastTime Schedule Normal Rec. Analog Camera Channels Ch ~ ChWeekday Start/End Setting Time ScheduleDay Start/End Special Time RecordingEvent Recording Setting Special TimeAlarm Rec. Analog Camera Channels Ch ~ Ch MD AreaSensor 1/2/3/4 Setting MD Area Pre Alarm secText Post Alarm sec Setup RelaySpecial Time Seq. Switchingsec Alarm Pop-up/Pop-up HoldsecMonitor Audio SystemRecording / Monitoring TextSync Text With DeviceSeek Header Timeout msDelimiter LinesTo designate Weekday/Weekend and Day/Night Time ScheduleSpecial Time Admin Password User PasswordRemote Setup SecurityAuto Del. Alarm Disk SetupBackup Reminder Auto Del. NormalNetwork NetworkDNS Server IP Address IP Address, NetMask, and Gateway AddressXDSL User ID/PasswordHRS Interval HRSGroup ID Monitoring Port / Playback Port TP Server PortFirewall / Port Serial Setup InterfaceBaud rate/Parity/Stop bit/Data bit Remote Control ID How to register remote controllerMiscellaneous Reset Values Alarm BuzzerKeyboard Control Addr Keyboard PTZ AddrUtility Disk Manager Type Activating IP Cam menus Using IP CamConfiguration Camera Setting IP Camera Channels Ch ~ ChIP AddressURL PortBand Width LimitKB/s Local IP Cam List SearchSelect Cam Normal Rec. IP Camera Channels Ch ~ Ch Alarm Rec. IP Cam Channel Ch ~ Ch Recording Speed/Quality & Pre Alarm & Post AlarmIP Cam Event Connecting External Device Using Text DeviceSetting at Text menu Setting at Alarm Rec. menu Setting at Serial Setup’s RS232 menuSetting at Normal Rec. menu Setting at Serial Setup’s PTZ menu Using KeyboardAppendix Appendix #1 Technical Specification Appendix Appendix #2.1 Introduction Appendix #2 Utilizing IP Addresses on Local Network#2.2 IP construction and Network class IP constructionFeatures of Addresses Network configuration To use as one network#2.3 C-class Network To use as three sub-networks 1/4 + 1/4 + 1/2 To use as two sub-networks 1/2 + 1/2To use as four sub-networks 1/4 + 1/4 + 1/4 + 1/4 Appendix