Rugged Outback ELX4-60 manual Relay, Setup, Special Time

Page 34

ELX4 -60

BASIC CONFIGURATION

5.5. Relay

This menu is to set the relay commands according to each time schedule. Relay commands are only used with events triggered with the four analog channels.

Setup

Alarm triggered events (MD or Sensors) can be set to trigger Relays 1 through 4. When set, the event will trigger the corresponding digital output.

Special Time

Enable “Special Time” to apply the relay schedule to the Special Time Zone.

34

2003.05.21 (v 1.0)

Rugged CCTV

Image 34

Contents ELX4-60 User’s Guide Cctv Monitor UserFCC Compliance Statement Important Notice ELX4 Rugged CctvSetting at Text menu Setting at Serial Setup’s RS232 menu Appendix #2 Utilizing IP Addresses on Local Network What is ELX4-60? IntroductionKey features ELX4-60Product Description Front PanelRear Panel DIOInstallation Summary Viewing single full screen MonitoringViewing basic screen Quad-split Viewing multi screenViewing all channels with sequence mode Viewing images with Digital Zoom Viewing an alarm triggered channelViewing with connected PTZ Pan/Tilt Control Load PresetSave Preset Zoom/Focus ControlPlayback via various mode Using RelayUsing Screen Lock PlaybackPlayback with Digital Zoom Playback via split screenVarious playback modes Using Search Mode Button controlSeconds Copy / Backup / Delete Data ManagerCopy Image Select DiskBackup Manager Start Date & Time / End Date & TimeDelete Data ConfigurationQuick Setup Date/TimeTime Format Time ZoneDaylight Saving Date/TimeRecording Recording Speed/Quality Configuration StatusChannel Status Audio RecordingCamera Analog Camera Channels Ch ~ Ch NameTIP Color StatusType Gain/Brightness/ContrastNormal Rec. Analog Camera Channels Ch ~ Ch Time ScheduleDay Start/End Setting Time ScheduleWeekday Start/End Special Time RecordingSetting Special Time Event RecordingMD Area Alarm Rec. Analog Camera Channels Ch ~ ChSensor 1/2/3/4 Pre Alarm sec Setting MD AreaText Post Alarm sec Relay SetupSpecial Time Alarm Pop-up/Pop-up Holdsec Seq. SwitchingsecMonitor System AudioSync Text With TextRecording / Monitoring DeviceDelimiter Timeout msSeek Header LinesTime Schedule To designate Weekday/Weekend and Day/NightSpecial Time Remote Setup User PasswordAdmin Password SecurityBackup Reminder Disk SetupAuto Del. Alarm Auto Del. NormalNetwork NetworkIP Address, NetMask, and Gateway Address DNS Server IP AddressUser ID/Password XDSLHRS HRS IntervalGroup ID TP Server Port Monitoring Port / Playback PortFirewall / Port Interface Serial SetupBaud rate/Parity/Stop bit/Data bit How to register remote controller Remote Control IDMiscellaneous Keyboard Control Addr Alarm BuzzerReset Values Keyboard PTZ AddrUtility Disk Manager Type Using IP Cam Activating IP Cam menusCamera Setting IP Camera Channels Ch ~ Ch ConfigurationPort IP AddressURLBand Width LimitKB/s Search Local IP Cam ListSelect Cam Normal Rec. IP Camera Channels Ch ~ Ch Recording Speed/Quality & Pre Alarm & Post Alarm Alarm Rec. IP Cam Channel Ch ~ ChIP Cam Event Using Text Device Connecting External DeviceSetting at Text menu Setting at Serial Setup’s RS232 menu Setting at Alarm Rec. menuSetting at Normal Rec. menu Using Keyboard Setting at Serial Setup’s PTZ menuAppendix Appendix #1 Technical Specification Appendix Appendix #2.2 IP construction and Network class Appendix #2 Utilizing IP Addresses on Local Network#2.1 Introduction IP constructionNetwork configuration To use as one network Features of Addresses#2.3 C-class Network To use as two sub-networks 1/2 + 1/2 To use as three sub-networks 1/4 + 1/4 + 1/2To use as four sub-networks 1/4 + 1/4 + 1/4 + 1/4 Appendix