Rugged Outback ELX4-60 manual Recording / Monitoring, Sync Text With, Device

Page 37

BASIC CONFIGURATION

ELX4 -60

5.7.2. Text

ELX4-60 can display and playback text data of Access Control/POS/ATM with relevant video.

Recording / Monitoring

In order to make ELX4 -60 input text data, both of menus should be set as “On”.

Sync Text With

To set channel to synchronize with text.

Device

Currently the protocol of Star Finger 007(Access control model) is built in ELX4-60 as text device. Rugged CCTV will keep updating such protocols. When connecting another text device, set as “Manual”. Then manual mode setting menu will be displayed. Set each value with referring the manual of connected device.

Rugged CCTV

2003.05.21 (v 1.0)

37

Image 37

Contents User’s Guide Cctv Monitor User ELX4-60FCC Compliance Statement Important Notice Rugged Cctv ELX4Setting at Text menu Setting at Serial Setup’s RS232 menu Appendix #2 Utilizing IP Addresses on Local Network Introduction What is ELX4-60?ELX4-60 Key featuresFront Panel Product DescriptionDIO Rear PanelInstallation Summary Viewing basic screen Quad-split MonitoringViewing single full screen Viewing multi screenViewing all channels with sequence mode Viewing images with Digital Zoom Viewing an alarm triggered channelViewing with connected PTZ Save Preset Load PresetPan/Tilt Control Zoom/Focus ControlUsing Screen Lock Using RelayPlayback via various mode PlaybackPlayback with Digital Zoom Playback via split screenVarious playback modes Button control Using Search ModeCopy Image Copy / Backup / Delete Data ManagerSeconds Select DiskStart Date & Time / End Date & Time Backup ManagerQuick Setup ConfigurationDelete Data Date/TimeDaylight Saving Time ZoneTime Format Date/TimeRecording Channel Status Configuration StatusRecording Speed/Quality Audio RecordingName Camera Analog Camera Channels Ch ~ ChTIP Type StatusColor Gain/Brightness/ContrastTime Schedule Normal Rec. Analog Camera Channels Ch ~ ChWeekday Start/End Setting Time ScheduleDay Start/End Special Time RecordingEvent Recording Setting Special TimeMD Area Alarm Rec. Analog Camera Channels Ch ~ ChSensor 1/2/3/4 Pre Alarm sec Setting MD AreaText Post Alarm sec Relay SetupSpecial Time Alarm Pop-up/Pop-up Holdsec Seq. SwitchingsecMonitor Audio SystemRecording / Monitoring TextSync Text With DeviceSeek Header Timeout msDelimiter LinesTo designate Weekday/Weekend and Day/Night Time ScheduleSpecial Time Admin Password User PasswordRemote Setup SecurityAuto Del. Alarm Disk SetupBackup Reminder Auto Del. NormalNetwork NetworkDNS Server IP Address IP Address, NetMask, and Gateway AddressXDSL User ID/PasswordHRS Interval HRSGroup ID TP Server Port Monitoring Port / Playback PortFirewall / Port Interface Serial SetupBaud rate/Parity/Stop bit/Data bit How to register remote controller Remote Control IDMiscellaneous Reset Values Alarm BuzzerKeyboard Control Addr Keyboard PTZ AddrUtility Disk Manager Type Activating IP Cam menus Using IP CamConfiguration Camera Setting IP Camera Channels Ch ~ ChPort IP AddressURLBand Width LimitKB/s Search Local IP Cam ListSelect Cam Normal Rec. IP Camera Channels Ch ~ Ch Recording Speed/Quality & Pre Alarm & Post Alarm Alarm Rec. IP Cam Channel Ch ~ ChIP Cam Event Using Text Device Connecting External DeviceSetting at Text menu Setting at Alarm Rec. menu Setting at Serial Setup’s RS232 menuSetting at Normal Rec. menu Setting at Serial Setup’s PTZ menu Using KeyboardAppendix Appendix #1 Technical Specification Appendix Appendix #2.1 Introduction Appendix #2 Utilizing IP Addresses on Local Network#2.2 IP construction and Network class IP constructionNetwork configuration To use as one network Features of Addresses#2.3 C-class Network To use as three sub-networks 1/4 + 1/4 + 1/2 To use as two sub-networks 1/2 + 1/2To use as four sub-networks 1/4 + 1/4 + 1/4 + 1/4 Appendix