Rugged Outback ELX4-60 manual Monitoring Port / Playback Port, TP Server Port, Firewall / Port

Page 48

ELX4 -60

BASIC CONFIGURATION

5.7.7.4.Port Setting

Monitoring Port / Playback Port

ELX4-60 uses port 8001 for Monitoring and port 8105 for Playback. To change the port numb er to an open port (some firewalls and/or ISPs block certain ports), press the [ENTER] button and use the dialogue box.

TP Server Port

The port used for Transparent Protocol server.

Firewall / Port

If there is a firewall on the network and a unique port is available, user may configure the Monitor and Playback ports as one port. In order to change a port, select “Port ” menu, and configure a suitable port value.

48

2003.05.21 (v 1.0)

Rugged CCTV

Image 48

Contents ELX4-60 User’s Guide Cctv Monitor UserFCC Compliance Statement Important Notice ELX4 Rugged CctvSetting at Text menu Setting at Serial Setup’s RS232 menu Appendix #2 Utilizing IP Addresses on Local Network What is ELX4-60? IntroductionKey features ELX4-60Product Description Front PanelRear Panel DIOInstallation Summary Monitoring Viewing basic screen Quad-splitViewing single full screen Viewing multi screenViewing all channels with sequence mode Viewing an alarm triggered channel Viewing images with Digital ZoomViewing with connected PTZ Load Preset Save PresetPan/Tilt Control Zoom/Focus ControlUsing Relay Using Screen LockPlayback via various mode PlaybackPlayback via split screen Playback with Digital ZoomVarious playback modes Using Search Mode Button controlCopy / Backup / Delete Data Manager Copy ImageSeconds Select DiskBackup Manager Start Date & Time / End Date & TimeConfiguration Quick SetupDelete Data Date/TimeTime Zone Daylight SavingTime Format Date/TimeRecording Configuration Status Channel StatusRecording Speed/Quality Audio RecordingCamera Analog Camera Channels Ch ~ Ch NameTIP Status TypeColor Gain/Brightness/ContrastNormal Rec. Analog Camera Channels Ch ~ Ch Time ScheduleSetting Time Schedule Weekday Start/EndDay Start/End Special Time RecordingSetting Special Time Event RecordingAlarm Rec. Analog Camera Channels Ch ~ Ch MD AreaSensor 1/2/3/4 Setting MD Area Pre Alarm secText Post Alarm sec Setup RelaySpecial Time Seq. Switchingsec Alarm Pop-up/Pop-up HoldsecMonitor System AudioText Recording / MonitoringSync Text With DeviceTimeout ms Seek HeaderDelimiter LinesTime Schedule To designate Weekday/Weekend and Day/NightSpecial Time User Password Admin PasswordRemote Setup SecurityDisk Setup Auto Del. AlarmBackup Reminder Auto Del. NormalNetwork NetworkIP Address, NetMask, and Gateway Address DNS Server IP AddressUser ID/Password XDSLHRS HRS IntervalGroup ID Monitoring Port / Playback Port TP Server PortFirewall / Port Serial Setup InterfaceBaud rate/Parity/Stop bit/Data bit Remote Control ID How to register remote controllerMiscellaneous Alarm Buzzer Reset ValuesKeyboard Control Addr Keyboard PTZ AddrUtility Disk Manager Type Using IP Cam Activating IP Cam menusCamera Setting IP Camera Channels Ch ~ Ch ConfigurationIP AddressURL PortBand Width LimitKB/s Local IP Cam List SearchSelect Cam Normal Rec. IP Camera Channels Ch ~ Ch Alarm Rec. IP Cam Channel Ch ~ Ch Recording Speed/Quality & Pre Alarm & Post AlarmIP Cam Event Connecting External Device Using Text DeviceSetting at Text menu Setting at Serial Setup’s RS232 menu Setting at Alarm Rec. menuSetting at Normal Rec. menu Using Keyboard Setting at Serial Setup’s PTZ menuAppendix Appendix #1 Technical Specification Appendix Appendix Appendix #2 Utilizing IP Addresses on Local Network #2.1 Introduction#2.2 IP construction and Network class IP constructionFeatures of Addresses Network configuration To use as one network#2.3 C-class Network To use as two sub-networks 1/2 + 1/2 To use as three sub-networks 1/4 + 1/4 + 1/2To use as four sub-networks 1/4 + 1/4 + 1/4 + 1/4 Appendix