Rugged Outback ELX4-60 manual Time Schedule, To designate Weekday/Weekend and Day/Night

Page 39

BASIC CONFIGURATION

ELX4 -60

5.7.3. Time Schedule

To designate Weekday/Weekend and Day/Night.

Weekday Start/End

Press [ENTER] to access the Time Setting. Set the range for “Weekday ” between Monday and Sunday using the or buttons. “Weekend” is set automatically based on “Weekday” range.

Day Start/End

Set the range for “Day” using the up/down buttons. The “Night ” range is set automatically based on “Day” range .

.

Rugged CCTV

2003.05.21 (v 1.0)

39

Image 39

Contents User’s Guide Cctv Monitor User ELX4-60FCC Compliance Statement Important Notice Rugged Cctv ELX4Setting at Text menu Setting at Serial Setup’s RS232 menu Appendix #2 Utilizing IP Addresses on Local Network Introduction What is ELX4-60?ELX4-60 Key featuresFront Panel Product DescriptionDIO Rear PanelInstallation Summary Viewing multi screen MonitoringViewing basic screen Quad-split Viewing single full screenViewing all channels with sequence mode Viewing an alarm triggered channel Viewing images with Digital ZoomViewing with connected PTZ Zoom/Focus Control Load PresetSave Preset Pan/Tilt ControlPlayback Using RelayUsing Screen Lock Playback via various modePlayback via split screen Playback with Digital ZoomVarious playback modes Button control Using Search ModeSelect Disk Copy / Backup / Delete Data ManagerCopy Image SecondsStart Date & Time / End Date & Time Backup ManagerDate/Time ConfigurationQuick Setup Delete DataDate/Time Time ZoneDaylight Saving Time FormatRecording Audio Recording Configuration StatusChannel Status Recording Speed/QualityName Camera Analog Camera Channels Ch ~ ChTIP Gain/Brightness/Contrast StatusType ColorTime Schedule Normal Rec. Analog Camera Channels Ch ~ ChSpecial Time Recording Setting Time ScheduleWeekday Start/End Day Start/EndEvent Recording Setting Special TimeAlarm Rec. Analog Camera Channels Ch ~ Ch MD AreaSensor 1/2/3/4 Setting MD Area Pre Alarm secText Post Alarm sec Setup RelaySpecial Time Seq. Switchingsec Alarm Pop-up/Pop-up HoldsecMonitor Audio SystemDevice TextRecording / Monitoring Sync Text WithLines Timeout msSeek Header DelimiterTo designate Weekday/Weekend and Day/Night Time ScheduleSpecial Time Security User PasswordAdmin Password Remote SetupAuto Del. Normal Disk SetupAuto Del. Alarm Backup ReminderNetwork NetworkDNS Server IP Address IP Address, NetMask, and Gateway AddressXDSL User ID/PasswordHRS Interval HRSGroup ID Monitoring Port / Playback Port TP Server PortFirewall / Port Serial Setup InterfaceBaud rate/Parity/Stop bit/Data bit Remote Control ID How to register remote controllerMiscellaneous Keyboard PTZ Addr Alarm BuzzerReset Values Keyboard Control AddrUtility Disk Manager Type Activating IP Cam menus Using IP CamConfiguration Camera Setting IP Camera Channels Ch ~ ChIP AddressURL PortBand Width LimitKB/s Local IP Cam List SearchSelect Cam Normal Rec. IP Camera Channels Ch ~ Ch Alarm Rec. IP Cam Channel Ch ~ Ch Recording Speed/Quality & Pre Alarm & Post AlarmIP Cam Event Connecting External Device Using Text DeviceSetting at Text menu Setting at Alarm Rec. menu Setting at Serial Setup’s RS232 menuSetting at Normal Rec. menu Setting at Serial Setup’s PTZ menu Using KeyboardAppendix Appendix #1 Technical Specification Appendix Appendix IP construction Appendix #2 Utilizing IP Addresses on Local Network#2.1 Introduction #2.2 IP construction and Network classFeatures of Addresses Network configuration To use as one network#2.3 C-class Network To use as three sub-networks 1/4 + 1/4 + 1/2 To use as two sub-networks 1/2 + 1/2To use as four sub-networks 1/4 + 1/4 + 1/4 + 1/4 Appendix