Rugged Outback ELX4-60 manual Disk Manager

Page 53

BASIC CONFIGURATION

ELX4 -60

5.8.1. Disk Manager

A connected HDD is detected automatically.

Select Disk

To select a Disk.

Action

Select from “Add/Remove/Format/Confirm Removed/Add used”.

[Add]	: To add disk
[Remove]	: To remove current HDD formatted for use.
[Format]	: To set format. In this case, “Alarm Partition” menu is activated.
[Confirm	: Removed HDDs are still listed in the system and can be re-added (“Add
Removed]	Used”) without losing data. “Confirm Removed” will permanently remove the
	drive and all data will be lost.
[Add used]	: It is to add a HDD that has been previously used. The disk does not need to be
	re-formatted.

Rugged CCTV

2003.05.21 (v 1.0)

53

Image 53

Contents User’s Guide Cctv Monitor User ELX4-60FCC Compliance Statement Important Notice Rugged Cctv ELX4Setting at Text menu Setting at Serial Setup’s RS232 menu Appendix #2 Utilizing IP Addresses on Local Network Introduction What is ELX4-60?ELX4-60 Key featuresFront Panel Product DescriptionDIO Rear PanelInstallation Summary Viewing basic screen Quad-split MonitoringViewing single full screen Viewing multi screenViewing all channels with sequence mode Viewing with connected PTZ Viewing an alarm triggered channelViewing images with Digital Zoom Save Preset Load PresetPan/Tilt Control Zoom/Focus ControlUsing Screen Lock Using RelayPlayback via various mode PlaybackVarious playback modes Playback via split screenPlayback with Digital Zoom Button control Using Search ModeCopy Image Copy / Backup / Delete Data ManagerSeconds Select DiskStart Date & Time / End Date & Time Backup ManagerQuick Setup ConfigurationDelete Data Date/TimeDaylight Saving Time ZoneTime Format Date/TimeRecording Channel Status Configuration StatusRecording Speed/Quality Audio RecordingName Camera Analog Camera Channels Ch ~ ChTIP Type StatusColor Gain/Brightness/ContrastTime Schedule Normal Rec. Analog Camera Channels Ch ~ ChWeekday Start/End Setting Time ScheduleDay Start/End Special Time RecordingEvent Recording Setting Special TimeSensor 1/2/3/4 Alarm Rec. Analog Camera Channels Ch ~ ChMD Area Text Setting MD AreaPre Alarm sec Post Alarm sec Special Time SetupRelay Monitor Seq. SwitchingsecAlarm Pop-up/Pop-up Holdsec Audio SystemRecording / Monitoring TextSync Text With DeviceSeek Header Timeout msDelimiter LinesTo designate Weekday/Weekend and Day/Night Time ScheduleSpecial Time Admin Password User PasswordRemote Setup SecurityAuto Del. Alarm Disk SetupBackup Reminder Auto Del. NormalNetwork NetworkDNS Server IP Address IP Address, NetMask, and Gateway AddressXDSL User ID/PasswordHRS Interval HRSGroup ID Firewall / Port Monitoring Port / Playback PortTP Server Port Baud rate/Parity/Stop bit/Data bit Serial SetupInterface Miscellaneous Remote Control IDHow to register remote controller Reset Values Alarm BuzzerKeyboard Control Addr Keyboard PTZ AddrUtility Disk Manager Type Activating IP Cam menus Using IP CamConfiguration Camera Setting IP Camera Channels Ch ~ ChBand Width LimitKB/s IP AddressURLPort Select Cam Local IP Cam ListSearch Normal Rec. IP Camera Channels Ch ~ Ch IP Cam Event Alarm Rec. IP Cam Channel Ch ~ ChRecording Speed/Quality & Pre Alarm & Post Alarm Setting at Text menu Connecting External DeviceUsing Text Device Setting at Alarm Rec. menu Setting at Serial Setup’s RS232 menuSetting at Normal Rec. menu Setting at Serial Setup’s PTZ menu Using KeyboardAppendix Appendix #1 Technical Specification Appendix Appendix #2.1 Introduction Appendix #2 Utilizing IP Addresses on Local Network#2.2 IP construction and Network class IP construction#2.3 C-class Network Features of AddressesNetwork configuration To use as one network To use as three sub-networks 1/4 + 1/4 + 1/2 To use as two sub-networks 1/2 + 1/2To use as four sub-networks 1/4 + 1/4 + 1/4 + 1/4 Appendix