Rugged Outback ELX4-60 manual Using IP Cam, Activating IP Cam menus

Page 55

ADVANCED CONFIGURATION

ELX4 -60

Advanced Configuration

ELX4-60 has the default settings of IP camera channels disabled. ELX4 -60 can support 12 IP channels and 4 analog cameras simultaneously. And current system can be expandable easily with connecting text or keyboard device.

6. Using IP Cam

6.1. Activating IP Cam menus

To setup the IP cam menu, first enable the IPCam Menu under the “System” tab.

Button control

-Move to “Miscellaneous” below “System” tab.

-Set “IP Cam Menu” t o “Enable.” This will activate the IP cam menus for the Configuration Menu.

Rugged CCTV

2003.05.21 (v 1.0)

55

Image 55

Contents User’s Guide Cctv Monitor User ELX4-60FCC Compliance Statement Important Notice Rugged Cctv ELX4Setting at Text menu Setting at Serial Setup’s RS232 menu Appendix #2 Utilizing IP Addresses on Local Network Introduction What is ELX4-60?ELX4-60 Key featuresFront Panel Product DescriptionDIO Rear PanelInstallation Summary Viewing multi screen MonitoringViewing basic screen Quad-split Viewing single full screenViewing all channels with sequence mode Viewing images with Digital Zoom Viewing an alarm triggered channelViewing with connected PTZ Zoom/Focus Control Load PresetSave Preset Pan/Tilt ControlPlayback Using RelayUsing Screen Lock Playback via various modePlayback with Digital Zoom Playback via split screenVarious playback modes Button control Using Search ModeSelect Disk Copy / Backup / Delete Data ManagerCopy Image SecondsStart Date & Time / End Date & Time Backup ManagerDate/Time ConfigurationQuick Setup Delete DataDate/Time Time ZoneDaylight Saving Time FormatRecording Audio Recording Configuration StatusChannel Status Recording Speed/QualityName Camera Analog Camera Channels Ch ~ ChTIP Gain/Brightness/Contrast StatusType ColorTime Schedule Normal Rec. Analog Camera Channels Ch ~ ChSpecial Time Recording Setting Time ScheduleWeekday Start/End Day Start/EndEvent Recording Setting Special TimeMD Area Alarm Rec. Analog Camera Channels Ch ~ ChSensor 1/2/3/4 Pre Alarm sec Setting MD AreaText Post Alarm sec Relay SetupSpecial Time Alarm Pop-up/Pop-up Holdsec Seq. SwitchingsecMonitor Audio SystemDevice TextRecording / Monitoring Sync Text WithLines Timeout msSeek Header DelimiterTo designate Weekday/Weekend and Day/Night Time ScheduleSpecial Time Security User PasswordAdmin Password Remote SetupAuto Del. Normal Disk SetupAuto Del. Alarm Backup ReminderNetwork NetworkDNS Server IP Address IP Address, NetMask, and Gateway AddressXDSL User ID/PasswordHRS Interval HRSGroup ID TP Server Port Monitoring Port / Playback PortFirewall / Port Interface Serial SetupBaud rate/Parity/Stop bit/Data bit How to register remote controller Remote Control IDMiscellaneous Keyboard PTZ Addr Alarm BuzzerReset Values Keyboard Control AddrUtility Disk Manager Type Activating IP Cam menus Using IP CamConfiguration Camera Setting IP Camera Channels Ch ~ ChPort IP AddressURLBand Width LimitKB/s Search Local IP Cam ListSelect Cam Normal Rec. IP Camera Channels Ch ~ Ch Recording Speed/Quality & Pre Alarm & Post Alarm Alarm Rec. IP Cam Channel Ch ~ ChIP Cam Event Using Text Device Connecting External DeviceSetting at Text menu Setting at Alarm Rec. menu Setting at Serial Setup’s RS232 menuSetting at Normal Rec. menu Setting at Serial Setup’s PTZ menu Using KeyboardAppendix Appendix #1 Technical Specification Appendix Appendix IP construction Appendix #2 Utilizing IP Addresses on Local Network#2.1 Introduction #2.2 IP construction and Network classNetwork configuration To use as one network Features of Addresses#2.3 C-class Network To use as three sub-networks 1/4 + 1/4 + 1/2 To use as two sub-networks 1/2 + 1/2To use as four sub-networks 1/4 + 1/4 + 1/4 + 1/4 Appendix