Rugged Outback ELX4-60 manual Camera Setting IP Camera Channels Ch ~ Ch, Configuration

Page 56

ELX4 -60

ADVANCED CONFIGURATION

6.2. Camera Setting – IP Camera Channels (Ch. 5 ~ Ch. 16)

Setting up the IP Cameras is similar to setting up the analog channels. However there are specific menus only for IP cam; for example, the ‘Configuration’ menu and ‘Network’ menu in the IP cam setting menu.

6.2.1. Configuration

Button control

-Press [MENU] button and move to each “IPCam #5 to #16“ below “Camera” menu. Then select “Configuration” menu by pressing the [ENTER] button and using the ￿ ￿ or ￿ ￿ buttons .

Name

Press the [ENTER] button to open the related dialogue box and change the camera name.

Status

Press the [ENTER] button and use the ￿ ￿ or ￿ ￿ buttons to set the camera to “On” or “Off.” Unlike the analog channels, the IP cam’s default value is “Off.” After registering the IP camera, set the status to “On.”

56

2003.05.21 (v 1.0)

Rugged CCTV

Image 56
Contents ELX4-60 User’s Guide Cctv Monitor UserFCC Compliance Statement Important Notice ELX4 Rugged CctvSetting at Text menu Setting at Serial Setup’s RS232 menu Appendix #2 Utilizing IP Addresses on Local Network What is ELX4-60? IntroductionKey features ELX4-60Product Description Front PanelRear Panel DIOInstallation Summary Monitoring Viewing basic screen Quad-splitViewing single full screen Viewing multi screenViewing all channels with sequence mode Viewing with connected PTZ Viewing an alarm triggered channelViewing images with Digital Zoom Load Preset Save PresetPan/Tilt Control Zoom/Focus ControlUsing Relay Using Screen LockPlayback via various mode PlaybackVarious playback modes Playback via split screenPlayback with Digital Zoom Using Search Mode Button controlCopy / Backup / Delete Data Manager Copy ImageSeconds Select DiskBackup Manager Start Date & Time / End Date & TimeConfiguration Quick SetupDelete Data Date/TimeTime Zone Daylight SavingTime Format Date/TimeRecording Configuration Status Channel StatusRecording Speed/Quality Audio RecordingCamera Analog Camera Channels Ch ~ Ch NameTIP Status TypeColor Gain/Brightness/ContrastNormal Rec. Analog Camera Channels Ch ~ Ch Time ScheduleSetting Time Schedule Weekday Start/EndDay Start/End Special Time RecordingSetting Special Time Event RecordingSensor 1/2/3/4 Alarm Rec. Analog Camera Channels Ch ~ ChMD Area Text Setting MD AreaPre Alarm sec Post Alarm sec Special Time SetupRelay Monitor Seq. SwitchingsecAlarm Pop-up/Pop-up Holdsec System AudioText Recording / MonitoringSync Text With DeviceTimeout ms Seek HeaderDelimiter LinesTime Schedule To designate Weekday/Weekend and Day/NightSpecial Time User Password Admin PasswordRemote Setup SecurityDisk Setup Auto Del. AlarmBackup Reminder Auto Del. NormalNetwork NetworkIP Address, NetMask, and Gateway Address DNS Server IP AddressUser ID/Password XDSLHRS HRS IntervalGroup ID Firewall / Port Monitoring Port / Playback PortTP Server Port Baud rate/Parity/Stop bit/Data bit Serial SetupInterface Miscellaneous Remote Control IDHow to register remote controller Alarm Buzzer Reset ValuesKeyboard Control Addr Keyboard PTZ AddrUtility Disk Manager Type Using IP Cam Activating IP Cam menusCamera Setting IP Camera Channels Ch ~ Ch ConfigurationBand Width LimitKB/s IP AddressURLPort Select Cam Local IP Cam ListSearch Normal Rec. IP Camera Channels Ch ~ Ch IP Cam Event Alarm Rec. IP Cam Channel Ch ~ ChRecording Speed/Quality & Pre Alarm & Post Alarm Setting at Text menu Connecting External DeviceUsing Text Device Setting at Serial Setup’s RS232 menu Setting at Alarm Rec. menuSetting at Normal Rec. menu Using Keyboard Setting at Serial Setup’s PTZ menuAppendix Appendix #1 Technical Specification Appendix Appendix Appendix #2 Utilizing IP Addresses on Local Network #2.1 Introduction#2.2 IP construction and Network class IP construction#2.3 C-class Network Features of AddressesNetwork configuration To use as one network To use as two sub-networks 1/2 + 1/2 To use as three sub-networks 1/4 + 1/4 + 1/2To use as four sub-networks 1/4 + 1/4 + 1/4 + 1/4 Appendix