Powerware 2500 manual Tower Setup with Three Cabinets

Page 27

INSTALLATION

NOTE Pedestals are required for installations with one or two cabinets. Joining brackets are required for installations with two or more cabinets.

Air Vents

Figure 12. Tower Setup with Three Cabinets

10.Align each joining bracket with the adjacent corner screw holes and secure with the supplied screws (see Figure 13).

UPS

EBM

Joining Bracket

Joining Bracket

Figure 13. Installing the Joining Brackets (Top View with Pedestals)

11.If installing additional EBMs, repeat Step 10 for each cabinet.

12.If installing optional EBMs, continue to the following section, “Extended Battery Module Installation.” Otherwise, continue to “Plug-Receptacle UPS Installation” on page 25 or “Hardwired UPS Installation” on page 27 to complete the installation.

EATON Powerware® 9125 Two-in-One UPS (2500/3000 VA) User’s Guide S 164201374 Rev D	21
www.powerware.com

Image 27

Contents

Powerware 9125 Two-in-One UPS 2500/3000 VA User’s Guide FCC Part ICES-003 Class a EMC StatementsRequesting a Declaration of Conformity Special Symbols Table of Contents UPS Maintenance Specifications TroubleshootingWarranty Chapter Introduction Introduction R N I N G N G E RU T I O N SikkerhedsanvisningerR E A R S C H U W I N G V a R S E LBelangrijke Veiligheidsinstructies V a a RR O I T U S G E L E TTarkeita Turvaohjeita A R aN G E R Consignes de sécuritéSicherheitswarnungen R N U N GH T U N G Avvisi di sicurezza R I C O L OV E R T E N Z a R S I K T I G T E N Z I O N EViktig Sikkerhetsinformasion R L I GR I G O Regulamentos de SegurançaI D a D O V E R T Ê N C I aПредупреждения по мерам безопасности E C a U C I Ó N Advertencias de SeguridadL I G R O V E R T E N C I aSäkerhetsföreskrifter R aK T I G T Inspecting the Equipment Chapter InstallationUPS Setup Connecting the UPS Internal Battery Rack-Mount Setup Tower Setup Installing UPS Pedestals for One Cabinet Installing EBM Pedestals Tower Setup with Three Cabinets Typical EBM Installation 120V UPS Model Shown Extended Battery Module InstallationRemove the cover from the EBM cable as shown in Figure EBM Installation for E/EH UPS Models Only Typical Installation 120V UPS Model Shown Plug-Receptacle UPS InstallationFault Indicators Hardwired UPS Installation Typical Hardwired UPS Installation UPS Wire Function Function Position EUH ModelsSize Rating Torque Fault Indicators Remote Emergency Power-off Installation Repo Connector 3000 VA, 120V Rear Panel UPS Rear Panels3000 VA, 208-240V Hardwired Rear Panel Turning the UPS On Starting the UPS on BatteryInitiating the Self-Test Turning the UPS OffUPS Front Panel Operating ModesNormal Mode Battery Mode Bypass Mode Chapter Configuration Using Configuration Mode Configuration Mode Option LED Status Explanation LEDs Configuration Mode LEDs and OptionsConfiguration Slot Cards Additional UPS FeaturesSingle-Port Card Communication Port Pin Assignment Signal Name FunctionOn-Bypass Relay Jumper Network Transient Protector Network Transient ProtectorUPS Load Segments for 120V Models Load SegmentsStoring the UPS and Batteries UPS and Battery CareReplacing Batteries When to Replace BatteriesHow to Replace UPS Internal Batteries Slide the new battery trays into the UPS How to Replace Extended Battery Modules EBM Connections 120V UPS Model Shown Testing New BatteriesRecycling the Used Battery or UPS UPS Maintenance Model Number Power Levels Nominal Voltage Input Voltage Model SpecificationsTechnical Specifications Power ConnectionsEnvironmental and Safety Weights and DimensionsBattery Runtimes in Minutes at Full/Half Load BatteryAlarm Indicators Audible Alarms and UPS ConditionsAlarm or Condition Possible Cause Action Troubleshooting GuideShutdown Low Battery Alarm or Condition Possible Cause Action Shutdown imminentService and Support Two-Year Limited Warranty US and Canada WarrantyWarranty Ten-Year Pro-Rated Limited Warranty US and Canada Warranty Load Protection Guarantee US and Canada Warranty