Powerware 2500 manual Extended Battery Module Installation

Page 28

INSTALLATION

Extended Battery Module Installation

C A U T I O N

A small amount of arcing may occur when connecting an EBM to the UPS. This is normal and will not harm personnel. Insert the EBM cable into the UPS battery connector quickly and firmly.

To install the optional EBMs:

1.If installing an EBM with an E/EH UPS model, skip to Step 4; otherwise, continue to Step 2.

2.Plug the EBM cable(s) into the battery connector(s) as shown in Figure 14. Up to four EBMs may be connected to the UPS.

3.Continue to “Plug-Receptacle UPS Installation” on page 25 or “Hardwired UPS Installation” on page 27.

UPS

EBM Cable

EBM

EBM

UPS Battery Connector

EBM Battery

Connectors

Figure 14. Typical EBM Installation (120V UPS Model Shown)

22EATON Powerware® 9125 Two-in-One UPS (2500/3000 VA) User’s Guide S 164201374 Rev D www.powerware.com

Image 28

Contents

Powerware 9125 Two-in-One UPS 2500/3000 VA User’s Guide Class a EMC Statements FCC Part ICES-003Requesting a Declaration of Conformity Special Symbols Table of Contents Specifications Troubleshooting UPS MaintenanceWarranty Chapter Introduction Introduction N G E R R N I N GSikkerhedsanvisninger U T I O NR E V a R S E L Belangrijke VeiligheidsinstructiesV a a R A R S C H U W I N GG E L E T Tarkeita TurvaohjeitaA R a R O I T U SConsignes de sécurité N G E RR N U N G SicherheitswarnungenH T U N G R I C O L O Avvisi di sicurezzaV E R T E N Z a T E N Z I O N E Viktig SikkerhetsinformasionR L I G R S I K T I GRegulamentos de Segurança I D a D OV E R T Ê N C I a R I G OПредупреждения по мерам безопасности Advertencias de Seguridad L I G R OV E R T E N C I a E C a U C I Ó NR a SäkerhetsföreskrifterK T I G T Chapter Installation Inspecting the EquipmentConnecting the UPS Internal Battery UPS SetupRack-Mount Setup Tower Setup Installing UPS Pedestals for One Cabinet Installing EBM Pedestals Tower Setup with Three Cabinets Extended Battery Module Installation Typical EBM Installation 120V UPS Model ShownRemove the cover from the EBM cable as shown in Figure EBM Installation for E/EH UPS Models Only Plug-Receptacle UPS Installation Typical Installation 120V UPS Model ShownFault Indicators Hardwired UPS Installation Typical Hardwired UPS Installation Function Position EUH Models UPS Wire FunctionSize Rating Torque Fault Indicators Remote Emergency Power-off Installation Repo Connector UPS Rear Panels 3000 VA, 120V Rear Panel3000 VA, 208-240V Hardwired Rear Panel Starting the UPS on Battery Turning the UPS OnTurning the UPS Off Initiating the Self-TestOperating Modes UPS Front PanelNormal Mode Battery Mode Bypass Mode Chapter Configuration Using Configuration Mode Configuration Mode LEDs and Options Configuration Mode Option LED Status Explanation LEDsConfiguration Additional UPS Features Slot CardsSingle-Port Card Signal Name Function Communication Port Pin AssignmentOn-Bypass Relay Jumper Network Transient Protector Network Transient ProtectorLoad Segments UPS Load Segments for 120V ModelsUPS and Battery Care Storing the UPS and BatteriesWhen to Replace Batteries Replacing BatteriesHow to Replace UPS Internal Batteries Slide the new battery trays into the UPS How to Replace Extended Battery Modules Testing New Batteries EBM Connections 120V UPS Model ShownRecycling the Used Battery or UPS UPS Maintenance Model Specifications Model Number Power Levels Nominal Voltage Input VoltagePower Connections Technical SpecificationsWeights and Dimensions Environmental and SafetyBattery Battery Runtimes in Minutes at Full/Half LoadAudible Alarms and UPS Conditions Alarm IndicatorsTroubleshooting Guide Alarm or Condition Possible Cause ActionAlarm or Condition Possible Cause Action Shutdown imminent Shutdown Low BatteryService and Support Warranty Two-Year Limited Warranty US and CanadaWarranty Ten-Year Pro-Rated Limited Warranty US and Canada Warranty Load Protection Guarantee US and Canada Warranty