Powerware 2500 manual Hardwired UPS Installation, R N I N G

Page 33

INSTALLATION

Hardwired UPS Installation

W A R N I N G

Only qualified service personnel (such as a licensed electrician) shall perform the electrical installation. Risk of electrical shock.

C A U T I O N

SFor UPS models with hardwired outputs, overcurrent protection for the output AC circuit(s) is to be provided by others.

SFor UPS models with hardwired outputs, suitably rated disconnect switches for the output AC circuit(s) are to be provided by others.

NOTE Do not make unauthorized changes to the UPS or accessories; otherwise, damage may occur to your equipment and void your warranty.

The Powerware 9125 hardwired models require a dedicated branch circuit that meets the following requirements:

S16A, 2-pole circuit breaker for EH and GH models/20A, 2-pole circuit breaker for EUH models to provide short circuit and overcurrent protection

SThe protection device requires a two-pole disconnection device between the UPS output and the load

SThe breaker must be wall-mounted and readily accessible to the operator

SFor Europe, the breaker must be approved by the appropriate safety agency (such as TÜV or VDE) and have a contact air gap of at least 3 mm

S200–240 Vac

SSingle-phase

S50/60 Hz

SFlexible metal conduit (recommended for ease of service and maintenance)

EATON Powerware® 9125 Two-in-One UPS (2500/3000 VA) User’s Guide S 164201374 Rev D	27
www.powerware.com

Image 33

Contents

Powerware 9125 Two-in-One UPS 2500/3000 VA User’s Guide FCC Part ICES-003 Class a EMC StatementsRequesting a Declaration of Conformity Special Symbols Table of Contents UPS Maintenance Specifications TroubleshootingWarranty Chapter Introduction Introduction R N I N G N G E RU T I O N SikkerhedsanvisningerR E Belangrijke Veiligheidsinstructies V a R S E LV a a R A R S C H U W I N GTarkeita Turvaohjeita G E L E TA R a R O I T U SN G E R Consignes de sécuritéSicherheitswarnungen R N U N GH T U N G Avvisi di sicurezza R I C O L OV E R T E N Z a Viktig Sikkerhetsinformasion T E N Z I O N ER L I G R S I K T I GI D a D O Regulamentos de SegurançaV E R T Ê N C I a R I G OПредупреждения по мерам безопасности L I G R O Advertencias de SeguridadV E R T E N C I a E C a U C I Ó NSäkerhetsföreskrifter R aK T I G T Inspecting the Equipment Chapter InstallationUPS Setup Connecting the UPS Internal BatteryRack-Mount Setup Tower Setup Installing UPS Pedestals for One Cabinet Installing EBM Pedestals Tower Setup with Three Cabinets Typical EBM Installation 120V UPS Model Shown Extended Battery Module Installation Remove the cover from the EBM cable as shown in Figure EBM Installation for E/EH UPS Models Only Typical Installation 120V UPS Model Shown Plug-Receptacle UPS InstallationFault Indicators Hardwired UPS Installation Typical Hardwired UPS Installation UPS Wire Function Function Position EUH ModelsSize Rating Torque Fault Indicators Remote Emergency Power-off Installation Repo Connector 3000 VA, 120V Rear Panel UPS Rear Panels3000 VA, 208-240V Hardwired Rear Panel Turning the UPS On Starting the UPS on BatteryInitiating the Self-Test Turning the UPS OffUPS Front Panel Operating ModesNormal Mode Battery Mode Bypass Mode Chapter Configuration Using Configuration Mode Configuration Mode Option LED Status Explanation LEDs Configuration Mode LEDs and OptionsConfiguration Slot Cards Additional UPS FeaturesSingle-Port Card Communication Port Pin Assignment Signal Name FunctionOn-Bypass Relay Jumper Network Transient Protector Network Transient ProtectorUPS Load Segments for 120V Models Load SegmentsStoring the UPS and Batteries UPS and Battery CareReplacing Batteries When to Replace BatteriesHow to Replace UPS Internal Batteries Slide the new battery trays into the UPS How to Replace Extended Battery Modules EBM Connections 120V UPS Model Shown Testing New BatteriesRecycling the Used Battery or UPS UPS Maintenance Model Number Power Levels Nominal Voltage Input Voltage Model SpecificationsTechnical Specifications Power ConnectionsEnvironmental and Safety Weights and DimensionsBattery Runtimes in Minutes at Full/Half Load BatteryAlarm Indicators Audible Alarms and UPS ConditionsAlarm or Condition Possible Cause Action Troubleshooting GuideShutdown Low Battery Alarm or Condition Possible Cause Action Shutdown imminentService and Support Two-Year Limited Warranty US and Canada WarrantyWarranty Ten-Year Pro-Rated Limited Warranty US and Canada Warranty Load Protection Guarantee US and Canada Warranty