Powerware 2500 manual EBM Installation for E/EH UPS Models Only

Page 30

INSTALLATION

6.Plug the EBM cable into the UPS battery connector (see Figure 17).

7.Attach the fixed cover plate (supplied in the accessory kit) to the EBM cable as shown in Figure 17.

	UPS Battery Connector
	UPS
EBM Cable
EBM Cable with	EBM
Fixed Cover Plate	EBM
EBM Battery
Connector with	EBM
Cover
	Fixed Cover Plate

Figure 17. EBM Installation for E/EH UPS Models Only

8.If additional EBMs are to be installed, remove the EBM battery connector cover. Remove the cover from the EBM cable of the second cabinet and plug the EBM cable into the battery connector on the first EBM. Attach the fixed cover plate to the EBM cable.

Repeat for each additional EBM. Up to four EBMs may be connected to the UPS.

9.Continue to the following section, “Plug-Receptacle UPS Installation” or “Hardwired UPS Installation” on page 27.

24EATON Powerware® 9125 Two-in-One UPS (2500/3000 VA) User’s Guide S 164201374 Rev D www.powerware.com

Image 30

Contents

Powerware 9125 Two-in-One UPS 2500/3000 VA User’s Guide Class a EMC Statements FCC Part ICES-003Requesting a Declaration of Conformity Special Symbols Table of Contents UPS Maintenance Specifications TroubleshootingWarranty Chapter Introduction Introduction N G E R R N I N GU T I O N SikkerhedsanvisningerR E V a a R V a R S E LBelangrijke Veiligheidsinstructies A R S C H U W I N GA R a G E L E TTarkeita Turvaohjeita R O I T U SConsignes de sécurité N G E RSicherheitswarnungen R N U N GH T U N G Avvisi di sicurezza R I C O L OV E R T E N Z a R L I G T E N Z I O N EViktig Sikkerhetsinformasion R S I K T I GV E R T Ê N C I a Regulamentos de SegurançaI D a D O R I G OПредупреждения по мерам безопасности V E R T E N C I a Advertencias de SeguridadL I G R O E C a U C I Ó NSäkerhetsföreskrifter R aK T I G T Chapter Installation Inspecting the EquipmentConnecting the UPS Internal Battery UPS SetupRack-Mount Setup Tower Setup Installing UPS Pedestals for One Cabinet Installing EBM Pedestals Tower Setup with Three Cabinets Extended Battery Module Installation Typical EBM Installation 120V UPS Model ShownRemove the cover from the EBM cable as shown in Figure EBM Installation for E/EH UPS Models Only Plug-Receptacle UPS Installation Typical Installation 120V UPS Model ShownFault Indicators Hardwired UPS Installation Typical Hardwired UPS Installation UPS Wire Function Function Position EUH ModelsSize Rating Torque Fault Indicators Remote Emergency Power-off Installation Repo Connector UPS Rear Panels 3000 VA, 120V Rear Panel3000 VA, 208-240V Hardwired Rear Panel Starting the UPS on Battery Turning the UPS OnTurning the UPS Off Initiating the Self-TestOperating Modes UPS Front PanelNormal Mode Battery Mode Bypass Mode Chapter Configuration Using Configuration Mode Configuration Mode LEDs and Options Configuration Mode Option LED Status Explanation LEDsConfiguration Additional UPS Features Slot CardsSingle-Port Card Signal Name Function Communication Port Pin AssignmentOn-Bypass Relay Jumper Network Transient Protector Network Transient ProtectorLoad Segments UPS Load Segments for 120V ModelsUPS and Battery Care Storing the UPS and BatteriesWhen to Replace Batteries Replacing BatteriesHow to Replace UPS Internal Batteries Slide the new battery trays into the UPS How to Replace Extended Battery Modules Testing New Batteries EBM Connections 120V UPS Model ShownRecycling the Used Battery or UPS UPS Maintenance Model Specifications Model Number Power Levels Nominal Voltage Input VoltagePower Connections Technical SpecificationsWeights and Dimensions Environmental and SafetyBattery Battery Runtimes in Minutes at Full/Half LoadAudible Alarms and UPS Conditions Alarm IndicatorsTroubleshooting Guide Alarm or Condition Possible Cause ActionAlarm or Condition Possible Cause Action Shutdown imminent Shutdown Low BatteryService and Support Warranty Two-Year Limited Warranty US and CanadaWarranty Ten-Year Pro-Rated Limited Warranty US and Canada Warranty Load Protection Guarantee US and Canada Warranty