SUPER MICRO Computer 6113L-i Server Chassis Features, System Power, Control Panel, Backplane

Page 15

Chapter 1: Introduction

1-3 Server Chassis Features

The SC813HS-500/SC813Hi-500 is one of Supermicro's third-generation 1U chas- sis and features four SCSI/IDE hard drive bays, a slim CD-ROM drive and a revolutionary cooling design that can keep today's most powerful processors running well below their temperature thresholds. The following is a general outline of the main features of the SC813HS/SC813Hi-500 chassis.

System Power

When configured as a SuperServer 6113L-8/6113L-i, the SC813HS-500/SC813Hi- 500 chassis includes a 500W cold-swap power supply.

Control Panel

The SC813HS-500/SC813Hi-500 control panel provides important system moni- toring and control information. LEDs indicate power on, network activity, hard disk drive activity and system overheat conditions. Also present are a main power button and a system reset button.

I/O Backplane

The SC813HS-500/SC813Hi-500 is a 1U rackmount chassis. Its I/O backplane provides one full-length PCI-X slot, a COM port (another COM port is an onboard header located near the USB2/3 ports), one VGA port, two USB ports and two Ethernet (LAN) ports. (See Figure 1-2.)

Figure 1-2. I/O Backplane

VGA Port PCI-X Slot

COM1 Port

USB Ports Ethernet Ports External SCSI Port

 

(6113L-8 only)

1-5

Image 15
Contents Super Page Preface About This ManualManual Organization Advanced Serverboard Setup Advanced Chassis SetupBios Preface Table of Contents Advanced Serverboard Setup System SafetyBios Advanced Chassis SetupAppendices Appendix a Bios Error Beep CodesPage Overview Chapter IntroductionChipset Serverboard FeaturesOnboard Controllers/Ports Processors MemoryPCI Expansion Slots ATI Graphics ControllerE8870 Chipset Block Diagram Other FeaturesBackplane Server Chassis FeaturesSystem Power Control PanelCooling System Asia-Pacific Contacting SupermicroHeadquarters EuropePage Chapter Server Installation Preparing for SetupUnpacking the SuperServer 6113L-8/6113L-i Choosing a Setup Location Rack PrecautionsServer Precautions Installing the Server into a Rack Installing the Outer RailsIdentifying the Sections of the Rack Rails Installing the Rack Rails Installing the Server into the RackInstalling the Server into a Rack Front bezel is optional Installing the Server into a Telco Rack Checking the Serverboard Setup Page Checking the Drive Bay Setup Page Control Panel Buttons Chapter System InterfaceControl Panel LEDs Scsi Drive Carrier LEDs 6113L-8 only Page Electrical Safety Precautions Chapter System SafetyGeneral Safety Precautions ESD Precautions Operating Precautions Unpacking Chapter Advanced Serverboard SetupPrecautions Handling the i2DML-8G2/i2DML-iG2 ServerboardLocating the Components Itanium2 Processor and Heatsink InstallationInstalling Heatsink Retention Mechanism Installing the Heatsink Retention MechanismPointer Installing Itanium2 CPUsPins of the CPU are not Installing the Power PodsCPU power pod Power pod slotDual Itanium2 CPUs with Power Pods Installed Installing Heatsinks for CPUs without heatsinks CPUs 2 with Heatsinks Installed Connecting AC PowerConnecting Cables Connecting Data CablesConnecting Power Cables Front Control Panel Header Pins U66 Connecting the Control PanelInstalling Memory Dimm Installation See FigureI/O Ports Memory Support 6a. Side View of Dimm Installation into SocketPCI card installation Adding PCI CardsPCI-X slot Super i2DML-8G2 Serverboard DetailsJumper Description Default Setting Connector DescriptionI2DML-8G2/i2DML-iG2 Quick Reference Connector Definitions Overheat LED OH HDD LEDReset Button Power ButtonUniversal Serial Bus USB0/1 Chassis Intrusion Front Panel Universal Serial Bus HeaderSerial Ports Glan Ethernet PortsPower Fault Fan HeadersWake-On-Ring SMB SMB Power I2C ConnectorCmos Clear Jumper SettingsVGA Enable/Disable Explanation JumpersGlan Enable/Disable Watch Dog Enable/DisablePower Fail Alarm Enable/ Disable Debug LEDs Onboard IndicatorsScsi Enable/Disable 6113L-8 only Glan LEDsIDE Connectors Scsi and IDE Disk Drive ConnectionsScsi Activity LED 6113L-8 only Pin Ultra 320 Scsi Connectors J3 and J18 Ultra320 Scsi Connectors 6113L-8 onlyChapter Advanced Chassis Setup Static-Sensitive DevicesTools Required Chassis Front and Rear Views Control PanelSystem Fans System Fan FailureReplacing System Fans Removing the Front Bezel Drive Bay Installation/RemovalRemoving the Front Bezel Accessing the Drive BaysMounting a SCSI/IDE drive in a drive carrier SCSI/IDE Drive InstallationInstalling/removing hot-swap Scsi drives 6113L-8 only CD-ROM Drive Installation Removing the power supply Power SupplyPower Supply Failure Removing/Replacing the Power SupplyRemoving/Replacing the Power Supply Introduction ChapterSystem Time/System Date Main Setup ScreenLanguage Menu BSP InformationSuper IO Configuration Advanced Setup ScreenSerial Port1 Address/Serial Port2 Address IDE ConfigurationBlock Multi-Sector Transfer LBA/Large ModePrimary IDE Master/Slave, Secondary IDE Master/Slave TypeArmd Emulation Type DMA ModeA.R.T. For Hard disk drives Bit Data TransferBios Settings Configuration Quiet BootAtapi 80-Pin Cable Detection System Health Monitor Watch Dog Timer Value Peripheral Device ConfigurationPower Loss Control Watch Dog TimerUSB Configuration USB FunctionLegacy USB Support PCI IDE BusMaster PCI/PnP ConfigurationPCI Latency Timer Allocate IRQ to PCI VGAHardware Health Monitoring Health Function Security SettingsOverheat Temperature Trips Change Supervisor PasswordExit Saving Changes Change User PasswordClear User Password Exit OptionsLoad Optimal Defaults Load Fail-Safe DefaultsDiscard Changes Appendix a Bios Error Beep Codes IA-32 Error Beep CodesBeep Code Error Message Description Checkpoints Code Description IA-64 Common Debug CodesCheckpoint Code Description Appendix B Bios Post CodesRegister for date and time next Monochrome mode and color mode settings next 47h 60h 95h Introduction to the EFI Platform Appendix C Software InstallationAmibios Flash Page Page Page Adding the CD-ROM Boot Option in EFI IA64 OS Installation Page Appendix D System Specifications System Input Requirements WeightPower Supply System Cooling