SUPER MICRO Computer 6113L-8, 6113L-i user manual Other Features, E8870 Chipset Block Diagram

Page 14

SUPERSERVER 6113L-8/6113L-i User's Manual

Other Features

Other onboard features are included to promote system health. These include various voltage monitors, two CPU temperature sensors, four fan speed sensors, a chassis intrusion header, auto-switching voltage regulators, chassis and CPU overheat sensors, virus protection and BIOS rescue.

Figure 1-1. E8870 Chipset Block Diagram

			Processor 1			Processor 2
				LPC Bus			16 GB (Max.) DDR200
				LPC Bus				DIMM1
							MRH_D	DIMM1
		3x1MB					MRH_D	DIMM5
		3x1MB
		FWH					MRH_D	DIMM2
		FWH					MRH_D	DIMM6
	IDE1		IDE2		SNC			DIMM6
	IDE1		IDE2		SNC		MRH_D	DIMM3
			UDMA100				MRH_D	DIMM7
							MRH_D	DIMM4
							MRH_D	DIMM8
								DIMM8

VGA	PCI 32			Hublink0		Hublink0	P64H2		82546EB
			ICH4	Hublink0	SIOH	Hublink0	P64H2	PCI-X 133	GLAN
			ICH4		SIOH			PCI-X 133	GLAN
USB0/1/2/	USB 2.0								Cntrl
USB0/1/2/
3/4/5/6			LPC Bus				PCI-X 100
			LPC Bus				PCI-X 100
	LPC	3x1MB				LSI U320	PCI Slot	Riser Card
	LPC					LSI U320
	Super			IPMI		SCSI Cntrl
	I/O	FWH
	I/O
		COM1/2

Note: This is a general block diagram. Please see the previous Serverboard Features pages for details on the features of each serverboard.

1-4

Image 14

Contents Super Page Manual Organization PrefaceAbout This Manual Bios Advanced Serverboard SetupAdvanced Chassis Setup Preface Table of Contents System Safety Advanced Serverboard SetupAdvanced Chassis Setup BiosAppendix a Bios Error Beep Codes AppendicesPage Chapter Introduction OverviewServerboard Features ChipsetATI Graphics Controller Processors MemoryPCI Expansion Slots Onboard Controllers/PortsOther Features E8870 Chipset Block DiagramControl Panel Server Chassis FeaturesSystem Power BackplaneCooling System Europe Contacting SupermicroHeadquarters Asia-PacificPage Unpacking the SuperServer 6113L-8/6113L-i Chapter Server InstallationPreparing for Setup Server Precautions Choosing a Setup LocationRack Precautions Identifying the Sections of the Rack Rails Installing the Server into a RackInstalling the Outer Rails Installing the Server into the Rack Installing the Rack RailsInstalling the Server into a Rack Front bezel is optional Installing the Server into a Telco Rack Checking the Serverboard Setup Page Checking the Drive Bay Setup Page Chapter System Interface Control Panel ButtonsControl Panel LEDs Scsi Drive Carrier LEDs 6113L-8 only Page Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Handling the i2DML-8G2/i2DML-iG2 Serverboard Chapter Advanced Serverboard SetupPrecautions UnpackingItanium2 Processor and Heatsink Installation Locating the ComponentsInstalling the Heatsink Retention Mechanism Installing Heatsink Retention MechanismInstalling Itanium2 CPUs PointerPower pod slot Installing the Power PodsCPU power pod Pins of the CPU are notDual Itanium2 CPUs with Power Pods Installed Installing Heatsinks for CPUs without heatsinks Connecting AC Power CPUs 2 with Heatsinks InstalledConnecting Power Cables Connecting CablesConnecting Data Cables Connecting the Control Panel Front Control Panel Header Pins U66I/O Ports Installing MemoryDimm Installation See Figure 6a. Side View of Dimm Installation into Socket Memory SupportPCI-X slot PCI card installationAdding PCI Cards Serverboard Details Super i2DML-8G2I2DML-8G2/i2DML-iG2 Quick Reference Jumper Description Default SettingConnector Description Connector Definitions HDD LED Overheat LED OHUniversal Serial Bus USB0/1 Reset ButtonPower Button Glan Ethernet Ports Front Panel Universal Serial Bus HeaderSerial Ports Chassis IntrusionWake-On-Ring Power FaultFan Headers SMB Power I2C Connector SMBExplanation Jumpers Jumper SettingsVGA Enable/Disable Cmos ClearPower Fail Alarm Enable/ Disable Glan Enable/DisableWatch Dog Enable/Disable Glan LEDs Onboard IndicatorsScsi Enable/Disable 6113L-8 only Debug LEDsScsi Activity LED 6113L-8 only IDE ConnectorsScsi and IDE Disk Drive Connections Ultra320 Scsi Connectors 6113L-8 only Pin Ultra 320 Scsi Connectors J3 and J18Tools Required Chapter Advanced Chassis SetupStatic-Sensitive Devices Control Panel Chassis Front and Rear ViewsReplacing System Fans System FansSystem Fan Failure Drive Bay Installation/Removal Removing the Front BezelAccessing the Drive Bays Removing the Front BezelSCSI/IDE Drive Installation Mounting a SCSI/IDE drive in a drive carrierInstalling/removing hot-swap Scsi drives 6113L-8 only CD-ROM Drive Installation Removing/Replacing the Power Supply Power SupplyPower Supply Failure Removing the power supplyRemoving/Replacing the Power Supply Chapter IntroductionBSP Information Main Setup ScreenLanguage Menu System Time/System DateAdvanced Setup Screen Super IO ConfigurationIDE Configuration Serial Port1 Address/Serial Port2 AddressType LBA/Large ModePrimary IDE Master/Slave, Secondary IDE Master/Slave Block Multi-Sector TransferBit Data Transfer DMA ModeA.R.T. For Hard disk drives Armd Emulation TypeAtapi 80-Pin Cable Detection Bios Settings ConfigurationQuiet Boot System Health Monitor Watch Dog Timer Peripheral Device ConfigurationPower Loss Control Watch Dog Timer ValueLegacy USB Support USB ConfigurationUSB Function Allocate IRQ to PCI VGA PCI/PnP ConfigurationPCI Latency Timer PCI IDE BusMasterChange Supervisor Password Security SettingsOverheat Temperature Trips Hardware Health Monitoring Health FunctionExit Options Change User PasswordClear User Password Exit Saving ChangesDiscard Changes Load Optimal DefaultsLoad Fail-Safe Defaults Beep Code Error Message Description Appendix a Bios Error Beep CodesIA-32 Error Beep Codes IA-64 Common Debug Codes Checkpoints Code DescriptionAppendix B Bios Post Codes Checkpoint Code DescriptionRegister for date and time next Monochrome mode and color mode settings next 47h 60h 95h Appendix C Software Installation Introduction to the EFI PlatformAmibios Flash Page Page Page Adding the CD-ROM Boot Option in EFI IA64 OS Installation Page Appendix D System Specifications System Cooling WeightPower Supply System Input Requirements