SUPER MICRO Computer 6113L-i, 6113L-8 Bios Settings Configuration, Atapi 80-Pin Cable Detection

Page 79

Chapter 7: BIOS

ATA(PI) 80-Pin Cable Detection

This feature allows the BIOS to auto-detect the 80-pin ATA(PI) Cable. The options are "Host & Device", "Host" and "Device."

!BIOS Settings Configuration

This item allows the user to configure the system's boot settings.

Quiet Boot

Set this value to allow the boot up screen options to be modified between POST messages or OEM logo. Select Disabled to allow the computer system to display the POST messages. Select Enabled to allow the computer system to display the OEM logo.

7-7

Image 79

Contents Super Page About This Manual PrefaceManual Organization Advanced Chassis Setup Advanced Serverboard SetupBios Preface Table of Contents Advanced Serverboard Setup System SafetyBios Advanced Chassis SetupAppendices Appendix a Bios Error Beep CodesPage Overview Chapter IntroductionChipset Serverboard FeaturesOnboard Controllers/Ports Processors MemoryPCI Expansion Slots ATI Graphics ControllerE8870 Chipset Block Diagram Other FeaturesBackplane Server Chassis FeaturesSystem Power Control PanelCooling System Asia-Pacific Contacting SupermicroHeadquarters EuropePage Preparing for Setup Chapter Server InstallationUnpacking the SuperServer 6113L-8/6113L-i Rack Precautions Choosing a Setup LocationServer Precautions Installing the Outer Rails Installing the Server into a RackIdentifying the Sections of the Rack Rails Installing the Rack Rails Installing the Server into the RackInstalling the Server into a Rack Front bezel is optional Installing the Server into a Telco Rack Checking the Serverboard Setup Page Checking the Drive Bay Setup Page Control Panel Buttons Chapter System InterfaceControl Panel LEDs Scsi Drive Carrier LEDs 6113L-8 only Page Electrical Safety Precautions Chapter System SafetyGeneral Safety Precautions ESD Precautions Operating Precautions Unpacking Chapter Advanced Serverboard SetupPrecautions Handling the i2DML-8G2/i2DML-iG2 ServerboardLocating the Components Itanium2 Processor and Heatsink InstallationInstalling Heatsink Retention Mechanism Installing the Heatsink Retention MechanismPointer Installing Itanium2 CPUsPins of the CPU are not Installing the Power PodsCPU power pod Power pod slotDual Itanium2 CPUs with Power Pods Installed Installing Heatsinks for CPUs without heatsinks CPUs 2 with Heatsinks Installed Connecting AC PowerConnecting Data Cables Connecting CablesConnecting Power Cables Front Control Panel Header Pins U66 Connecting the Control PanelDimm Installation See Figure Installing MemoryI/O Ports Memory Support 6a. Side View of Dimm Installation into SocketAdding PCI Cards PCI card installationPCI-X slot Super i2DML-8G2 Serverboard DetailsConnector Description Jumper Description Default SettingI2DML-8G2/i2DML-iG2 Quick Reference Connector Definitions Overheat LED OH HDD LEDPower Button Reset ButtonUniversal Serial Bus USB0/1 Chassis Intrusion Front Panel Universal Serial Bus HeaderSerial Ports Glan Ethernet PortsFan Headers Power FaultWake-On-Ring SMB SMB Power I2C ConnectorCmos Clear Jumper SettingsVGA Enable/Disable Explanation JumpersWatch Dog Enable/Disable Glan Enable/DisablePower Fail Alarm Enable/ Disable Debug LEDs Onboard IndicatorsScsi Enable/Disable 6113L-8 only Glan LEDsScsi and IDE Disk Drive Connections IDE ConnectorsScsi Activity LED 6113L-8 only Pin Ultra 320 Scsi Connectors J3 and J18 Ultra320 Scsi Connectors 6113L-8 onlyStatic-Sensitive Devices Chapter Advanced Chassis SetupTools Required Chassis Front and Rear Views Control PanelSystem Fan Failure System FansReplacing System Fans Removing the Front Bezel Drive Bay Installation/RemovalRemoving the Front Bezel Accessing the Drive BaysMounting a SCSI/IDE drive in a drive carrier SCSI/IDE Drive InstallationInstalling/removing hot-swap Scsi drives 6113L-8 only CD-ROM Drive Installation Removing the power supply Power SupplyPower Supply Failure Removing/Replacing the Power SupplyRemoving/Replacing the Power Supply Introduction ChapterSystem Time/System Date Main Setup ScreenLanguage Menu BSP InformationSuper IO Configuration Advanced Setup ScreenSerial Port1 Address/Serial Port2 Address IDE ConfigurationBlock Multi-Sector Transfer LBA/Large ModePrimary IDE Master/Slave, Secondary IDE Master/Slave TypeArmd Emulation Type DMA ModeA.R.T. For Hard disk drives Bit Data TransferQuiet Boot Bios Settings ConfigurationAtapi 80-Pin Cable Detection System Health Monitor Watch Dog Timer Value Peripheral Device ConfigurationPower Loss Control Watch Dog TimerUSB Function USB ConfigurationLegacy USB Support PCI IDE BusMaster PCI/PnP ConfigurationPCI Latency Timer Allocate IRQ to PCI VGAHardware Health Monitoring Health Function Security SettingsOverheat Temperature Trips Change Supervisor PasswordExit Saving Changes Change User PasswordClear User Password Exit OptionsLoad Fail-Safe Defaults Load Optimal DefaultsDiscard Changes IA-32 Error Beep Codes Appendix a Bios Error Beep CodesBeep Code Error Message Description Checkpoints Code Description IA-64 Common Debug CodesCheckpoint Code Description Appendix B Bios Post CodesRegister for date and time next Monochrome mode and color mode settings next 47h 60h 95h Introduction to the EFI Platform Appendix C Software InstallationAmibios Flash Page Page Page Adding the CD-ROM Boot Option in EFI IA64 OS Installation Page Appendix D System Specifications System Input Requirements WeightPower Supply System Cooling