SUPER MICRO Computer 6113L-i, 6113L-8 user manual Chapter System Interface, Control Panel Buttons

Page 29

Chapter 3: System Interface

Chapter 3

System Interface

3-1 Overview

There are several LEDs on the chassis control panel to keep you constantly informed of the overall status of the system as well as the activity and health of specific components. There are also two buttons on the chassis control panel and an on/off switch on the power supply. This chapter explains the meanings of all LED indicators and the appropriate response you may need to take.

3-2 Control Panel Buttons

There are two push-button buttons located on the front of the chassis. These are (in order from left to right) a reset button and a power on/off button.

RESET

!RESET: The reset switch reboots the system.

!POWER: This is the main power switch, which is used to apply or turn off the main system power. Turning off system power with this button removes the main power but keeps standby power supplied to the system.

3-1

Image 29

Contents Super Page Manual Organization PrefaceAbout This Manual Bios Advanced Serverboard SetupAdvanced Chassis Setup Preface Table of Contents Advanced Serverboard Setup System SafetyBios Advanced Chassis SetupAppendices Appendix a Bios Error Beep CodesPage Overview Chapter IntroductionChipset Serverboard FeaturesPCI Expansion Slots Processors MemoryATI Graphics Controller Onboard Controllers/PortsE8870 Chipset Block Diagram Other FeaturesSystem Power Server Chassis FeaturesControl Panel BackplaneCooling System Headquarters Contacting SupermicroEurope Asia-PacificPage Unpacking the SuperServer 6113L-8/6113L-i Chapter Server InstallationPreparing for Setup Server Precautions Choosing a Setup LocationRack Precautions Identifying the Sections of the Rack Rails Installing the Server into a RackInstalling the Outer Rails Installing the Rack Rails Installing the Server into the RackInstalling the Server into a Rack Front bezel is optional Installing the Server into a Telco Rack Checking the Serverboard Setup Page Checking the Drive Bay Setup Page Control Panel Buttons Chapter System InterfaceControl Panel LEDs Scsi Drive Carrier LEDs 6113L-8 only Page Electrical Safety Precautions Chapter System SafetyGeneral Safety Precautions ESD Precautions Operating Precautions Precautions Chapter Advanced Serverboard SetupHandling the i2DML-8G2/i2DML-iG2 Serverboard UnpackingLocating the Components Itanium2 Processor and Heatsink InstallationInstalling Heatsink Retention Mechanism Installing the Heatsink Retention MechanismPointer Installing Itanium2 CPUsCPU power pod Installing the Power PodsPower pod slot Pins of the CPU are notDual Itanium2 CPUs with Power Pods Installed Installing Heatsinks for CPUs without heatsinks CPUs 2 with Heatsinks Installed Connecting AC PowerConnecting Power Cables Connecting CablesConnecting Data Cables Front Control Panel Header Pins U66 Connecting the Control PanelI/O Ports Installing MemoryDimm Installation See Figure Memory Support 6a. Side View of Dimm Installation into SocketPCI-X slot PCI card installationAdding PCI Cards Super i2DML-8G2 Serverboard DetailsI2DML-8G2/i2DML-iG2 Quick Reference Jumper Description Default SettingConnector Description Connector Definitions Overheat LED OH HDD LEDUniversal Serial Bus USB0/1 Reset ButtonPower Button Serial Ports Front Panel Universal Serial Bus HeaderGlan Ethernet Ports Chassis IntrusionWake-On-Ring Power FaultFan Headers SMB SMB Power I2C ConnectorVGA Enable/Disable Jumper SettingsExplanation Jumpers Cmos ClearPower Fail Alarm Enable/ Disable Glan Enable/DisableWatch Dog Enable/Disable Scsi Enable/Disable 6113L-8 only Onboard IndicatorsGlan LEDs Debug LEDsScsi Activity LED 6113L-8 only IDE ConnectorsScsi and IDE Disk Drive Connections Pin Ultra 320 Scsi Connectors J3 and J18 Ultra320 Scsi Connectors 6113L-8 onlyTools Required Chapter Advanced Chassis SetupStatic-Sensitive Devices Chassis Front and Rear Views Control PanelReplacing System Fans System FansSystem Fan Failure Removing the Front Bezel Drive Bay Installation/RemovalRemoving the Front Bezel Accessing the Drive BaysMounting a SCSI/IDE drive in a drive carrier SCSI/IDE Drive InstallationInstalling/removing hot-swap Scsi drives 6113L-8 only CD-ROM Drive Installation Power Supply Failure Power SupplyRemoving/Replacing the Power Supply Removing the power supplyRemoving/Replacing the Power Supply Introduction ChapterLanguage Menu Main Setup ScreenBSP Information System Time/System DateSuper IO Configuration Advanced Setup ScreenSerial Port1 Address/Serial Port2 Address IDE ConfigurationPrimary IDE Master/Slave, Secondary IDE Master/Slave LBA/Large ModeType Block Multi-Sector TransferA.R.T. For Hard disk drives DMA ModeBit Data Transfer Armd Emulation TypeAtapi 80-Pin Cable Detection Bios Settings ConfigurationQuiet Boot System Health Monitor Power Loss Control Peripheral Device ConfigurationWatch Dog Timer Watch Dog Timer ValueLegacy USB Support USB ConfigurationUSB Function PCI Latency Timer PCI/PnP ConfigurationAllocate IRQ to PCI VGA PCI IDE BusMasterOverheat Temperature Trips Security SettingsChange Supervisor Password Hardware Health Monitoring Health FunctionClear User Password Change User PasswordExit Options Exit Saving ChangesDiscard Changes Load Optimal DefaultsLoad Fail-Safe Defaults Beep Code Error Message Description Appendix a Bios Error Beep CodesIA-32 Error Beep Codes Checkpoints Code Description IA-64 Common Debug CodesCheckpoint Code Description Appendix B Bios Post CodesRegister for date and time next Monochrome mode and color mode settings next 47h 60h 95h Introduction to the EFI Platform Appendix C Software InstallationAmibios Flash Page Page Page Adding the CD-ROM Boot Option in EFI IA64 OS Installation Page Appendix D System Specifications Power Supply WeightSystem Cooling System Input Requirements