SUPER MICRO Computer 6113L-8, 6113L-i USB Configuration, USB Function, Legacy USB Support

Page 82

SUPERSERVER 6113L-8/6113L-i User's Manual

!USB Configuration

This feature allows the user to configure the USB settings.

USB Function

Select "Enabled" to enable the USB Host Controller. The options are "Disabled" and "Enabled."

Legacy USB Support

Select "Enabled" to enable support for USB Legacy. The options are "Disabled" and "Enabled."

7-10

Image 82

Contents Super Page About This Manual PrefaceManual Organization Advanced Chassis Setup Advanced Serverboard SetupBios Preface Table of Contents System Safety Advanced Serverboard SetupAdvanced Chassis Setup BiosAppendix a Bios Error Beep Codes AppendicesPage Chapter Introduction OverviewServerboard Features ChipsetATI Graphics Controller Processors MemoryPCI Expansion Slots Onboard Controllers/PortsOther Features E8870 Chipset Block DiagramControl Panel Server Chassis FeaturesSystem Power BackplaneCooling System Europe Contacting SupermicroHeadquarters Asia-PacificPage Preparing for Setup Chapter Server InstallationUnpacking the SuperServer 6113L-8/6113L-i Rack Precautions Choosing a Setup LocationServer Precautions Installing the Outer Rails Installing the Server into a RackIdentifying the Sections of the Rack Rails Installing the Server into the Rack Installing the Rack RailsInstalling the Server into a Rack Front bezel is optional Installing the Server into a Telco Rack Checking the Serverboard Setup Page Checking the Drive Bay Setup Page Chapter System Interface Control Panel ButtonsControl Panel LEDs Scsi Drive Carrier LEDs 6113L-8 only Page Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Handling the i2DML-8G2/i2DML-iG2 Serverboard Chapter Advanced Serverboard SetupPrecautions UnpackingItanium2 Processor and Heatsink Installation Locating the ComponentsInstalling the Heatsink Retention Mechanism Installing Heatsink Retention MechanismInstalling Itanium2 CPUs PointerPower pod slot Installing the Power PodsCPU power pod Pins of the CPU are notDual Itanium2 CPUs with Power Pods Installed Installing Heatsinks for CPUs without heatsinks Connecting AC Power CPUs 2 with Heatsinks InstalledConnecting Data Cables Connecting CablesConnecting Power Cables Connecting the Control Panel Front Control Panel Header Pins U66Dimm Installation See Figure Installing MemoryI/O Ports 6a. Side View of Dimm Installation into Socket Memory SupportAdding PCI Cards PCI card installationPCI-X slot Serverboard Details Super i2DML-8G2Connector Description Jumper Description Default SettingI2DML-8G2/i2DML-iG2 Quick Reference Connector Definitions HDD LED Overheat LED OHPower Button Reset ButtonUniversal Serial Bus USB0/1 Glan Ethernet Ports Front Panel Universal Serial Bus HeaderSerial Ports Chassis IntrusionFan Headers Power FaultWake-On-Ring SMB Power I2C Connector SMBExplanation Jumpers Jumper SettingsVGA Enable/Disable Cmos ClearWatch Dog Enable/Disable Glan Enable/DisablePower Fail Alarm Enable/ Disable Glan LEDs Onboard IndicatorsScsi Enable/Disable 6113L-8 only Debug LEDsScsi and IDE Disk Drive Connections IDE ConnectorsScsi Activity LED 6113L-8 only Ultra320 Scsi Connectors 6113L-8 only Pin Ultra 320 Scsi Connectors J3 and J18Static-Sensitive Devices Chapter Advanced Chassis SetupTools Required Control Panel Chassis Front and Rear ViewsSystem Fan Failure System FansReplacing System Fans Drive Bay Installation/Removal Removing the Front BezelAccessing the Drive Bays Removing the Front BezelSCSI/IDE Drive Installation Mounting a SCSI/IDE drive in a drive carrierInstalling/removing hot-swap Scsi drives 6113L-8 only CD-ROM Drive Installation Removing/Replacing the Power Supply Power SupplyPower Supply Failure Removing the power supplyRemoving/Replacing the Power Supply Chapter IntroductionBSP Information Main Setup ScreenLanguage Menu System Time/System DateAdvanced Setup Screen Super IO ConfigurationIDE Configuration Serial Port1 Address/Serial Port2 AddressType LBA/Large ModePrimary IDE Master/Slave, Secondary IDE Master/Slave Block Multi-Sector TransferBit Data Transfer DMA ModeA.R.T. For Hard disk drives Armd Emulation TypeQuiet Boot Bios Settings ConfigurationAtapi 80-Pin Cable Detection System Health Monitor Watch Dog Timer Peripheral Device ConfigurationPower Loss Control Watch Dog Timer ValueUSB Function USB ConfigurationLegacy USB Support Allocate IRQ to PCI VGA PCI/PnP ConfigurationPCI Latency Timer PCI IDE BusMasterChange Supervisor Password Security SettingsOverheat Temperature Trips Hardware Health Monitoring Health FunctionExit Options Change User PasswordClear User Password Exit Saving ChangesLoad Fail-Safe Defaults Load Optimal DefaultsDiscard Changes IA-32 Error Beep Codes Appendix a Bios Error Beep CodesBeep Code Error Message Description IA-64 Common Debug Codes Checkpoints Code DescriptionAppendix B Bios Post Codes Checkpoint Code DescriptionRegister for date and time next Monochrome mode and color mode settings next 47h 60h 95h Appendix C Software Installation Introduction to the EFI PlatformAmibios Flash Page Page Page Adding the CD-ROM Boot Option in EFI IA64 OS Installation Page Appendix D System Specifications System Cooling WeightPower Supply System Input Requirements