SUPER MICRO Computer 6113L-8, 6113L-i IA-64 Common Debug Codes, Checkpoints Code Description

Page 88

SUPERSERVER 6113L-8/6113L-i User's Manual

A-2 IA-64 Common Debug Codes

Common Debug Codes for IA-64 systems are listed below:

Checkpoints		Code Description
DS4	DS3
On	On:	SNC found and start memory sizing
On	Off:	Initial system memory and SIOH
Off	On:	Valid memory and SIOH found
Off	Off:	ICH4 found

Note: The debug code LEDs (DS3 and DS4) are located next to the IDE2 connector. Please refer to the serverboard layout in Chapter 5 for DS3 and DS4 locations.

A-2

Image 88

Contents Super Page About This Manual PrefaceManual Organization Advanced Chassis Setup Advanced Serverboard SetupBios Preface Table of Contents System Safety Advanced Serverboard SetupAdvanced Chassis Setup BiosAppendix a Bios Error Beep Codes AppendicesPage Chapter Introduction OverviewServerboard Features ChipsetProcessors Memory PCI Expansion SlotsATI Graphics Controller Onboard Controllers/PortsOther Features E8870 Chipset Block DiagramServer Chassis Features System PowerControl Panel BackplaneCooling System Contacting Supermicro HeadquartersEurope Asia-PacificPage Preparing for Setup Chapter Server InstallationUnpacking the SuperServer 6113L-8/6113L-i Rack Precautions Choosing a Setup LocationServer Precautions Installing the Outer Rails Installing the Server into a RackIdentifying the Sections of the Rack Rails Installing the Server into the Rack Installing the Rack RailsInstalling the Server into a Rack Front bezel is optional Installing the Server into a Telco Rack Checking the Serverboard Setup Page Checking the Drive Bay Setup Page Chapter System Interface Control Panel ButtonsControl Panel LEDs Scsi Drive Carrier LEDs 6113L-8 only Page Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Chapter Advanced Serverboard Setup PrecautionsHandling the i2DML-8G2/i2DML-iG2 Serverboard UnpackingItanium2 Processor and Heatsink Installation Locating the ComponentsInstalling the Heatsink Retention Mechanism Installing Heatsink Retention MechanismInstalling Itanium2 CPUs PointerInstalling the Power Pods CPU power podPower pod slot Pins of the CPU are notDual Itanium2 CPUs with Power Pods Installed Installing Heatsinks for CPUs without heatsinks Connecting AC Power CPUs 2 with Heatsinks InstalledConnecting Data Cables Connecting CablesConnecting Power Cables Connecting the Control Panel Front Control Panel Header Pins U66Dimm Installation See Figure Installing MemoryI/O Ports 6a. Side View of Dimm Installation into Socket Memory SupportAdding PCI Cards PCI card installationPCI-X slot Serverboard Details Super i2DML-8G2Connector Description Jumper Description Default SettingI2DML-8G2/i2DML-iG2 Quick Reference Connector Definitions HDD LED Overheat LED OHPower Button Reset ButtonUniversal Serial Bus USB0/1 Front Panel Universal Serial Bus Header Serial PortsGlan Ethernet Ports Chassis IntrusionFan Headers Power FaultWake-On-Ring SMB Power I2C Connector SMBJumper Settings VGA Enable/DisableExplanation Jumpers Cmos ClearWatch Dog Enable/Disable Glan Enable/DisablePower Fail Alarm Enable/ Disable Onboard Indicators Scsi Enable/Disable 6113L-8 onlyGlan LEDs Debug LEDsScsi and IDE Disk Drive Connections IDE ConnectorsScsi Activity LED 6113L-8 only Ultra320 Scsi Connectors 6113L-8 only Pin Ultra 320 Scsi Connectors J3 and J18Static-Sensitive Devices Chapter Advanced Chassis SetupTools Required Control Panel Chassis Front and Rear ViewsSystem Fan Failure System FansReplacing System Fans Drive Bay Installation/Removal Removing the Front BezelAccessing the Drive Bays Removing the Front BezelSCSI/IDE Drive Installation Mounting a SCSI/IDE drive in a drive carrierInstalling/removing hot-swap Scsi drives 6113L-8 only CD-ROM Drive Installation Power Supply Power Supply FailureRemoving/Replacing the Power Supply Removing the power supplyRemoving/Replacing the Power Supply Chapter IntroductionMain Setup Screen Language MenuBSP Information System Time/System DateAdvanced Setup Screen Super IO ConfigurationIDE Configuration Serial Port1 Address/Serial Port2 AddressLBA/Large Mode Primary IDE Master/Slave, Secondary IDE Master/SlaveType Block Multi-Sector TransferDMA Mode A.R.T. For Hard disk drivesBit Data Transfer Armd Emulation TypeQuiet Boot Bios Settings ConfigurationAtapi 80-Pin Cable Detection System Health Monitor Peripheral Device Configuration Power Loss ControlWatch Dog Timer Watch Dog Timer ValueUSB Function USB ConfigurationLegacy USB Support PCI/PnP Configuration PCI Latency TimerAllocate IRQ to PCI VGA PCI IDE BusMasterSecurity Settings Overheat Temperature TripsChange Supervisor Password Hardware Health Monitoring Health FunctionChange User Password Clear User PasswordExit Options Exit Saving ChangesLoad Fail-Safe Defaults Load Optimal DefaultsDiscard Changes IA-32 Error Beep Codes Appendix a Bios Error Beep CodesBeep Code Error Message Description IA-64 Common Debug Codes Checkpoints Code DescriptionAppendix B Bios Post Codes Checkpoint Code DescriptionRegister for date and time next Monochrome mode and color mode settings next 47h 60h 95h Appendix C Software Installation Introduction to the EFI PlatformAmibios Flash Page Page Page Adding the CD-ROM Boot Option in EFI IA64 OS Installation Page Appendix D System Specifications Weight Power SupplySystem Cooling System Input Requirements