SUPER MICRO Computer 6113L-i user manual Installing/removing hot-swap Scsi drives 6113L-8 only

Page 69

Chapter 6: Advanced Chassis Setup

2.Installing/removing hot-swap SCSI drives (6113L-8 only):

The SCSI drive bays are located in the front of the chassis, making them easily accessible for installation and removal. The SCSI drives are hot-swap units, meaning that they can be installed and removed while the system is running. To remove a SCSI drive, first push the colored release button located beside the drive's LEDs, then swing the handle fully out and use it to pull the SCSI drive carrier straight out (see Figure 6-5).

Figure 6-5. Removing SCSI Drives

Important: All of the SCSI drive carriers must remain in

!the drive bays to maintain proper cooling airflow.

6-7

Image 69

Contents Super Page Preface About This ManualManual Organization Advanced Serverboard Setup Advanced Chassis SetupBios Preface Table of Contents Advanced Serverboard Setup System SafetyBios Advanced Chassis SetupAppendices Appendix a Bios Error Beep CodesPage Overview Chapter IntroductionChipset Serverboard FeaturesPCI Expansion Slots Processors MemoryATI Graphics Controller Onboard Controllers/PortsE8870 Chipset Block Diagram Other FeaturesSystem Power Server Chassis FeaturesControl Panel BackplaneCooling System Headquarters Contacting SupermicroEurope Asia-PacificPage Chapter Server Installation Preparing for SetupUnpacking the SuperServer 6113L-8/6113L-i Choosing a Setup Location Rack PrecautionsServer Precautions Installing the Server into a Rack Installing the Outer RailsIdentifying the Sections of the Rack Rails Installing the Rack Rails Installing the Server into the RackInstalling the Server into a Rack Front bezel is optional Installing the Server into a Telco Rack Checking the Serverboard Setup Page Checking the Drive Bay Setup Page Control Panel Buttons Chapter System InterfaceControl Panel LEDs Scsi Drive Carrier LEDs 6113L-8 only Page Electrical Safety Precautions Chapter System SafetyGeneral Safety Precautions ESD Precautions Operating Precautions Precautions Chapter Advanced Serverboard SetupHandling the i2DML-8G2/i2DML-iG2 Serverboard UnpackingLocating the Components Itanium2 Processor and Heatsink InstallationInstalling Heatsink Retention Mechanism Installing the Heatsink Retention MechanismPointer Installing Itanium2 CPUsCPU power pod Installing the Power PodsPower pod slot Pins of the CPU are notDual Itanium2 CPUs with Power Pods Installed Installing Heatsinks for CPUs without heatsinks CPUs 2 with Heatsinks Installed Connecting AC PowerConnecting Cables Connecting Data CablesConnecting Power Cables Front Control Panel Header Pins U66 Connecting the Control PanelInstalling Memory Dimm Installation See FigureI/O Ports Memory Support 6a. Side View of Dimm Installation into SocketPCI card installation Adding PCI CardsPCI-X slot Super i2DML-8G2 Serverboard DetailsJumper Description Default Setting Connector DescriptionI2DML-8G2/i2DML-iG2 Quick Reference Connector Definitions Overheat LED OH HDD LEDReset Button Power ButtonUniversal Serial Bus USB0/1 Serial Ports Front Panel Universal Serial Bus HeaderGlan Ethernet Ports Chassis IntrusionPower Fault Fan HeadersWake-On-Ring SMB SMB Power I2C ConnectorVGA Enable/Disable Jumper SettingsExplanation Jumpers Cmos ClearGlan Enable/Disable Watch Dog Enable/DisablePower Fail Alarm Enable/ Disable Scsi Enable/Disable 6113L-8 only Onboard IndicatorsGlan LEDs Debug LEDsIDE Connectors Scsi and IDE Disk Drive ConnectionsScsi Activity LED 6113L-8 only Pin Ultra 320 Scsi Connectors J3 and J18 Ultra320 Scsi Connectors 6113L-8 onlyChapter Advanced Chassis Setup Static-Sensitive DevicesTools Required Chassis Front and Rear Views Control PanelSystem Fans System Fan FailureReplacing System Fans Removing the Front Bezel Drive Bay Installation/RemovalRemoving the Front Bezel Accessing the Drive BaysMounting a SCSI/IDE drive in a drive carrier SCSI/IDE Drive InstallationInstalling/removing hot-swap Scsi drives 6113L-8 only CD-ROM Drive Installation Power Supply Failure Power SupplyRemoving/Replacing the Power Supply Removing the power supplyRemoving/Replacing the Power Supply Introduction ChapterLanguage Menu Main Setup ScreenBSP Information System Time/System DateSuper IO Configuration Advanced Setup ScreenSerial Port1 Address/Serial Port2 Address IDE ConfigurationPrimary IDE Master/Slave, Secondary IDE Master/Slave LBA/Large ModeType Block Multi-Sector TransferA.R.T. For Hard disk drives DMA ModeBit Data Transfer Armd Emulation TypeBios Settings Configuration Quiet BootAtapi 80-Pin Cable Detection System Health Monitor Power Loss Control Peripheral Device ConfigurationWatch Dog Timer Watch Dog Timer ValueUSB Configuration USB FunctionLegacy USB Support PCI Latency Timer PCI/PnP ConfigurationAllocate IRQ to PCI VGA PCI IDE BusMasterOverheat Temperature Trips Security SettingsChange Supervisor Password Hardware Health Monitoring Health FunctionClear User Password Change User PasswordExit Options Exit Saving ChangesLoad Optimal Defaults Load Fail-Safe DefaultsDiscard Changes Appendix a Bios Error Beep Codes IA-32 Error Beep CodesBeep Code Error Message Description Checkpoints Code Description IA-64 Common Debug CodesCheckpoint Code Description Appendix B Bios Post CodesRegister for date and time next Monochrome mode and color mode settings next 47h 60h 95h Introduction to the EFI Platform Appendix C Software InstallationAmibios Flash Page Page Page Adding the CD-ROM Boot Option in EFI IA64 OS Installation Page Appendix D System Specifications Power Supply WeightSystem Cooling System Input Requirements