SUPER MICRO Computer 6113L-8, 6113L-i user manual Amibios Flash

Page 96

SUPER 6113L-8/6113L-i User's Manual

C-2 AMIBIOS Flash

1.Obtain a USB Pen or a USB storage device (a USB 2.0 device is recommended).

2.From our web site (www.supermicro.com), download the following two files into the USB pen or device: [amiflash.efi], and [bios.rom].

3.Connect the USB device to one of the USB ports (see Chapter 5 for USB port locations).

4.Bootup the system with the USB pen connected to a USB port. The system will boot to the “EFI Boot Manager”. Highlight the “EFI Shell [Built-in]” field and press <Enter> to select it.

Boot to EFI Boot Manager

5.Once "EFI shell (Built-in)" is selected, you enter the "EFI Shell". In the “EFI Shell,” locate the USB device (for example fs0 or fs1).

C-2

Image 96
Contents Super Page Preface About This ManualManual Organization Advanced Serverboard Setup Advanced Chassis SetupBios Preface Table of Contents System Safety Advanced Serverboard SetupAdvanced Chassis Setup BiosAppendix a Bios Error Beep Codes AppendicesPage Chapter Introduction OverviewServerboard Features ChipsetProcessors Memory PCI Expansion SlotsATI Graphics Controller Onboard Controllers/PortsOther Features E8870 Chipset Block DiagramServer Chassis Features System PowerControl Panel BackplaneCooling System Contacting Supermicro HeadquartersEurope Asia-PacificPage Chapter Server Installation Preparing for SetupUnpacking the SuperServer 6113L-8/6113L-i Choosing a Setup Location Rack PrecautionsServer Precautions Installing the Server into a Rack Installing the Outer RailsIdentifying the Sections of the Rack Rails Installing the Server into the Rack Installing the Rack RailsInstalling the Server into a Rack Front bezel is optional Installing the Server into a Telco Rack Checking the Serverboard Setup Page Checking the Drive Bay Setup Page Chapter System Interface Control Panel ButtonsControl Panel LEDs Scsi Drive Carrier LEDs 6113L-8 only Page Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Chapter Advanced Serverboard Setup PrecautionsHandling the i2DML-8G2/i2DML-iG2 Serverboard UnpackingItanium2 Processor and Heatsink Installation Locating the ComponentsInstalling the Heatsink Retention Mechanism Installing Heatsink Retention MechanismInstalling Itanium2 CPUs PointerInstalling the Power Pods CPU power podPower pod slot Pins of the CPU are notDual Itanium2 CPUs with Power Pods Installed Installing Heatsinks for CPUs without heatsinks Connecting AC Power CPUs 2 with Heatsinks InstalledConnecting Cables Connecting Data CablesConnecting Power Cables Connecting the Control Panel Front Control Panel Header Pins U66Installing Memory Dimm Installation See FigureI/O Ports 6a. Side View of Dimm Installation into Socket Memory SupportPCI card installation Adding PCI CardsPCI-X slot Serverboard Details Super i2DML-8G2Jumper Description Default Setting Connector DescriptionI2DML-8G2/i2DML-iG2 Quick Reference Connector Definitions HDD LED Overheat LED OHReset Button Power ButtonUniversal Serial Bus USB0/1 Front Panel Universal Serial Bus Header Serial PortsGlan Ethernet Ports Chassis IntrusionPower Fault Fan HeadersWake-On-Ring SMB Power I2C Connector SMBJumper Settings VGA Enable/DisableExplanation Jumpers Cmos ClearGlan Enable/Disable Watch Dog Enable/DisablePower Fail Alarm Enable/ Disable Onboard Indicators Scsi Enable/Disable 6113L-8 onlyGlan LEDs Debug LEDsIDE Connectors Scsi and IDE Disk Drive ConnectionsScsi Activity LED 6113L-8 only Ultra320 Scsi Connectors 6113L-8 only Pin Ultra 320 Scsi Connectors J3 and J18Chapter Advanced Chassis Setup Static-Sensitive DevicesTools Required Control Panel Chassis Front and Rear ViewsSystem Fans System Fan FailureReplacing System Fans Drive Bay Installation/Removal Removing the Front BezelAccessing the Drive Bays Removing the Front BezelSCSI/IDE Drive Installation Mounting a SCSI/IDE drive in a drive carrierInstalling/removing hot-swap Scsi drives 6113L-8 only CD-ROM Drive Installation Power Supply Power Supply FailureRemoving/Replacing the Power Supply Removing the power supplyRemoving/Replacing the Power Supply Chapter IntroductionMain Setup Screen Language MenuBSP Information System Time/System DateAdvanced Setup Screen Super IO ConfigurationIDE Configuration Serial Port1 Address/Serial Port2 AddressLBA/Large Mode Primary IDE Master/Slave, Secondary IDE Master/SlaveType Block Multi-Sector TransferDMA Mode A.R.T. For Hard disk drivesBit Data Transfer Armd Emulation TypeBios Settings Configuration Quiet BootAtapi 80-Pin Cable Detection System Health Monitor Peripheral Device Configuration Power Loss ControlWatch Dog Timer Watch Dog Timer ValueUSB Configuration USB FunctionLegacy USB Support PCI/PnP Configuration PCI Latency TimerAllocate IRQ to PCI VGA PCI IDE BusMasterSecurity Settings Overheat Temperature TripsChange Supervisor Password Hardware Health Monitoring Health FunctionChange User Password Clear User PasswordExit Options Exit Saving ChangesLoad Optimal Defaults Load Fail-Safe DefaultsDiscard Changes Appendix a Bios Error Beep Codes IA-32 Error Beep CodesBeep Code Error Message Description IA-64 Common Debug Codes Checkpoints Code DescriptionAppendix B Bios Post Codes Checkpoint Code DescriptionRegister for date and time next Monochrome mode and color mode settings next 47h 60h 95h Appendix C Software Installation Introduction to the EFI PlatformAmibios Flash Page Page Page Adding the CD-ROM Boot Option in EFI IA64 OS Installation Page Appendix D System Specifications Weight Power SupplySystem Cooling System Input Requirements