SUPER MICRO Computer 6014L-T user manual Chapter Introduction, Overview

Page 11

Chapter 1: Introduction

Chapter 1

Introduction

1-1 Overview

The SuperServer 6014L-T is a high-end dual processor, 1U rackmount server featur- ing state-of-the-art technology. The 6014L-T is comprised of two main subsystems: the SC811LT-260 1U rackmount chassis and the X6DLP-EG2 serverboard. Please refer to our web site for information on operating systems that have been certifi ed for use with the 6014L-T (www.supermicro.com).

In addition to the serverboard and chassis, various hardware components may have been included with the 6014L-T, as listed below.

Two (2) CPU heatsinks (SNK-P0019)

One (1) slim CD-ROM drive [CDM-TEAC-24(B)]

One (1) fl oppy drive [FPD-PNSC-02(01)]

SATA Accessories:

Two (2) SATA hard drive carriers (CSE-PT-10(B))

One (1) internal SATA backplane (CSE-SATA-810)

Two (2) SATA cables (CBL-0061)

One (1) 3.3V 64-bit, 66 MHz PCI-X slot riser card (CSE-RR1U-X)

Two (2) 4-cm high-performance fans (FAN-0061)

Rackmount hardware with screws (CSE-PT8):

Two (2) rack rail assemblies

Six (6) brackets for mounting the rack rails in a rack/telco rack

One (1) CD containing drivers and utilities

SuperServer 6014L-T User's Manual

Note: "B" indicates part is also available in black.

1-1

Image 11
Contents Super Manual Revision Release Date March 6 Manual Organization PrefaceAbout This Manual Bios System SafetyAdvanced Serverboard Setup Advanced Chassis SetupPreface Table of Contents Advanced Serverboard Setup System SafetySMB Advanced Chassis SetupAppendices BiosPage Overview Chapter IntroductionPCI Expansion Slots Serverboard FeaturesProcessors Memory Serial ATAOnboard Controllers/Ports Other FeaturesIntel E7520 Chipset System Block Diagram Control Panel Server Chassis FeaturesSystem Power Serial ATA SubsystemRear I/O Panel Cooling SystemAsia-Pacific Contacting SupermicroHeadquarters EuropePage Unpacking the System Chapter Server InstallationPreparing for Setup Server Precautions Choosing a Setup LocationRack Precautions Rack Mounting Considerations Identifying the Sections of the Rack Rails Installing the System into a RackInstalling the Rack Rails Installing the Chassis RailsInstalling the Server into a Rack Installing the Server into the RackInstalling the Server into a Telco Rack Installing the Server into a Telco RackChecking the Serverboard Setup Accessing the Inside of the System Checking the Drive Bay Setup Control Panel Buttons Chapter System InterfaceControl Panel LEDs Serial ATA Drive Carrier LED Page Electrical Safety Precautions Chapter System SafetyGeneral Safety Precautions ESD Precautions Installing the Onboard Battery Operating PrecautionsUnpacking Chapter Advanced Serverboard SetupPrecautions Handling the ServerboardInstalling the Serverboard Serverboard InstallationInstalling the Heatsink Brackets Installing the Processors Processor and Heatsink InstallationInstalled heatsink Installing the HeatsinksInstalled processor Removing the Heatsink Connecting Power Cables Connecting CablesConnecting Data Cables I/O Ports Connecting the Control PanelMemory Support Installing MemoryDimm Installation See Figure PCI slots PCI card installationAdding PCI Cards Super X6DLP-EG2 Layout Serverboard DetailsX6DLP-EG2 Quick Reference Jumper Description Default SettingConnector Description Onboard Indicators DescriptionPower LED Connector DefinitionsATX Power Connector Processor Power ConnectorOverheat/Fan Fail LED Power Fail LEDNIC1/2 LEDs Chassis Intrusion Reset ButtonPower Button JLAN1/2 Ethernet PortsFan Headers Universal Serial Bus USB0/1Universal Serial Bus Headers Wake-On-LAN Speaker/Power LED/KeylockWake-On-Ring ATX PS/2 Keyboard and PS/2 Mouse Ports ConnectorPower Fault SMB Power I2 CCmos Clear Jumper SettingsJLAN1/2 Enable/Disable Explanation JumpersWatch Dog VGA Enable/DisablePower Force On SMBus to PCI SlotsSystem Status LED Onboard IndicatorsAlarm Reset Jlan LEDsOnboard LED Indicators DS7, DS8 Onboard LED Indicators DS1, DS5Parallel Printer Port Header Parallel Port, Floppy, IDE and Sata Drive ConnectionsSata Connectors Floppy ConnectorIDE Drive Connectors Pin Definitions IDE1, IDE2 IDE ConnectorsTools Required Chapter Advanced Chassis SetupPrecautions Static-Sensitive DevicesChassis Front View Control PanelSystem Fan Failure Drive Bay Installation/RemovalAccessing the Drive Bays System FansMounting a Serial ATA drive in a drive carrier Serial ATA Drive InstallationInstalling/removing hot-swap Serial ATA drives Serial ATA Backplane CD-ROM and Floppy Drive InstallationReplacing the Power Supply Power SupplyPower Supply Failure Page Introduction How To Change the Configuration DataChapter System Memory Main SetupProcessors System Time/System Date Advanced SettingsConfigure Advanced CPU Settings CPU Configuration Sub-MenuATA Ports Definition Combined Mode OperationIDE Configuration Sub-Menu IDE ConfigurationA.R.T. For Hard disk drives LBA/Large ModeType Block Multi-Sector TransferPCI/PnP Configuration Floppy ConfigurationOffboard PCI/ISA IDE Card Allocate IRQ to PCI VGAPalette Snooping PCI IDE BusMasterSuper IO Configuration Sub-Menu Advanced Chipset Settings Apci Configuration Power ConfigurationEvent Log Configuration Watch Dog TimerPCI/PCI Error Logging PCI/PCI Express Error LoggingPCI Express Configuration Remote Access ConfigurationMPS Configuration Sredir Memory Display Delay Remote AccessSerial Port Mode Redirection After Bios PostSystem Health Monitor USB ConfigurationFan1 Speed to Fan6 Speeds Boot SettingsSystem Fan Monitor Fan Speed Control ModesBios Settings Configuration CD/DVD Drives Boot Device PriorityHard Disk Drives Removable DrivesClear User Password Security SettingsChange Supervisor Password Change User PasswordDiscarding Changes and Exit Load Optimal DefaultsExit Options Saving Changes and ExitLoad Fail-Safe Defaults Beep Code Error Message Description Appendix a Bios Error Beep CodesAmibios Error Beep Codes DS7/DS8 LED Post Codes LED IndicatorsUncompressed Initialization Codes Appendix B Bios Post Checkpoint CodesBootblock Recovery Codes Uncompressed Initialization Codes Checkpoint Appendix B Bios Post Checkpoint Codes Checkpoint A9h Aah Abh B0h B1h 00h Page Intel 6300ESB I/O Controller Hub Appendix C Software InstallationSerial ATA Sata Adaptec RAID Configuration Utility ARC Configuring Sata RAIDAdaptec Sata HostRAID Controller Driver Using the Array Configuration Utility ACU Viewing Array Properties Managing ArraysCreating Arrays Deleting ArraysPage Assigning Array Properties RAID Levels Adding a Bootable Array To initialize drives Deleting a Bootable ArrayInitializing Disk Drives Page Page To rebuild an array Rebuilding ArraysTo access the disk utilities Using the Disk UtilitiesYou can choose from the following options Exiting the Adaptec RAID Configuration UtilityInstalling the ICH5R/6300 ESBDriver Installing Additional Drivers Installing Other Software Programs and DriversSupero Doctor Supero Doctor III Interface Display Screen-II Remote Control Page Appendix D System Specifications System Input Requirements WeightPower Supply System Cooling