SUPER MICRO Computer 6014L-T user manual Uncompressed Initialization Codes

Page 93

Appendix B: BIOS POST Checkpoint Codes

B-3 Uncompressed Initialization Codes

The following runtime checkpoint codes are listed in order of execution. These codes are uncompressed in F0000h shadow RAM.

Checkpoint

03h

05h

06h

07h

08h

0Ah

0Bh

0Ch

0Eh

0Fh

10h

11h

12h

13h

14h

19h

1Ah

2Bh

2Ch

2Dh

23h

24h

Code Description

The NMI is disabled. Next, checking for a soft reset or a power on condition.

The BIOS stack has been built. Next, disabling cache memory.

Uncompressing the POST code next.

Next, initializing the CPU and the CPU data area.

The CMOS checksum calculation is done next.

The CMOS checksum calculation is done. Initializing the CMOS status register for date and time next.

The CMOS status register is initialized. Next, performing any required initialization before the keyboard BAT command is issued.

The keyboard controller input buffer is free. Next, issuing the BAT command to the keyboard controller.

The keyboard controller BAT command result has been verifi ed. Next, performing any necessary initialization after the keyboard controller BAT command test.

The initialization after the keyboard controller BAT command test is done. The key- board command byte is written next.

The keyboard controller command byte is written. Next, issuing the Pin 23 and 24 blocking and unblocking command.

Next, checking if <End or <Ins> keys were pressed during power on. Initializing CMOS RAM if the Initialize CMOS RAM in every boot AMIBIOS POST option was set in AMIBCP or the <End> key was pressed.

Next, disabling DMA controllers 1 and 2 and interrupt controllers 1 and 2.

The video display has been disabled. Port B has been initialized. Next, initializing the chipset.

The 8254 timer test will begin next.

Next, programming the fl ash ROM.

The memory refresh line is toggling. Checking the 15 second on/off time next.

Passing control to the video ROM to perform any required confi guration before the video ROM test.

All necessary processing before passing control to the video ROM is done. Look- ing for the video ROM next and passing control to it.

The video ROM has returned control to BIOS POST. Performing any required pro- cessing after the video ROM had control

Reading the 8042 input port and disabling the MEGAKEY Green PC feature next. Making the BIOS code segment writable and performing any necessary confi gura- tion before initializing the interrupt vectors.

The confi guration required before interrupt vector initialization has completed. In- terrupt vector initialization is about to begin.

B-3

Image 93
Contents Super Manual Revision Release Date March 6 Preface About This ManualManual Organization Advanced Serverboard Setup System SafetyAdvanced Chassis Setup BiosPreface Table of Contents Advanced Serverboard Setup System SafetySMB Advanced Chassis SetupAppendices BiosPage Overview Chapter IntroductionProcessors Memory Serverboard FeaturesSerial ATA PCI Expansion SlotsOnboard Controllers/Ports Other FeaturesIntel E7520 Chipset System Block Diagram System Power Server Chassis FeaturesSerial ATA Subsystem Control PanelRear I/O Panel Cooling SystemHeadquarters Contacting SupermicroEurope Asia-PacificPage Chapter Server Installation Preparing for SetupUnpacking the System Choosing a Setup Location Rack PrecautionsServer Precautions Rack Mounting Considerations Identifying the Sections of the Rack Rails Installing the System into a RackInstalling the Rack Rails Installing the Chassis RailsInstalling the Server into a Rack Installing the Server into the RackInstalling the Server into a Telco Rack Installing the Server into a Telco RackChecking the Serverboard Setup Accessing the Inside of the System Checking the Drive Bay Setup Control Panel Buttons Chapter System InterfaceControl Panel LEDs Serial ATA Drive Carrier LED Page Electrical Safety Precautions Chapter System SafetyGeneral Safety Precautions ESD Precautions Installing the Onboard Battery Operating PrecautionsPrecautions Chapter Advanced Serverboard SetupHandling the Serverboard UnpackingServerboard Installation Installing the Heatsink BracketsInstalling the Serverboard Installing the Processors Processor and Heatsink InstallationInstalling the Heatsinks Installed processorInstalled heatsink Removing the Heatsink Connecting Cables Connecting Data CablesConnecting Power Cables I/O Ports Connecting the Control PanelInstalling Memory Dimm Installation See FigureMemory Support PCI card installation Adding PCI CardsPCI slots Super X6DLP-EG2 Layout Serverboard DetailsConnector Description Jumper Description Default SettingOnboard Indicators Description X6DLP-EG2 Quick ReferenceATX Power Connector Connector DefinitionsProcessor Power Connector Power LEDPower Fail LED NIC1/2 LEDsOverheat/Fan Fail LED Power Button Reset ButtonJLAN1/2 Ethernet Ports Chassis IntrusionUniversal Serial Bus USB0/1 Universal Serial Bus HeadersFan Headers Speaker/Power LED/Keylock Wake-On-RingWake-On-LAN Power Fault ConnectorSMB Power I2 C ATX PS/2 Keyboard and PS/2 Mouse PortsJLAN1/2 Enable/Disable Jumper SettingsExplanation Jumpers Cmos ClearPower Force On VGA Enable/DisableSMBus to PCI Slots Watch DogAlarm Reset Onboard IndicatorsJlan LEDs System Status LEDOnboard LED Indicators DS7, DS8 Onboard LED Indicators DS1, DS5Parallel Printer Port Header Parallel Port, Floppy, IDE and Sata Drive ConnectionsSata Connectors Floppy ConnectorIDE Drive Connectors Pin Definitions IDE1, IDE2 IDE ConnectorsPrecautions Chapter Advanced Chassis SetupStatic-Sensitive Devices Tools RequiredChassis Front View Control PanelAccessing the Drive Bays Drive Bay Installation/RemovalSystem Fans System Fan FailureMounting a Serial ATA drive in a drive carrier Serial ATA Drive InstallationInstalling/removing hot-swap Serial ATA drives Serial ATA Backplane CD-ROM and Floppy Drive InstallationPower Supply Power Supply FailureReplacing the Power Supply Page How To Change the Configuration Data ChapterIntroduction Main Setup ProcessorsSystem Memory Configure Advanced CPU Settings Advanced SettingsCPU Configuration Sub-Menu System Time/System DateIDE Configuration Sub-Menu Combined Mode OperationIDE Configuration ATA Ports DefinitionType LBA/Large ModeBlock Multi-Sector Transfer A.R.T. For Hard disk drivesPCI/PnP Configuration Floppy ConfigurationPalette Snooping Allocate IRQ to PCI VGAPCI IDE BusMaster Offboard PCI/ISA IDE CardSuper IO Configuration Sub-Menu Advanced Chipset Settings Apci Configuration Power ConfigurationPCI/PCI Error Logging Watch Dog TimerPCI/PCI Express Error Logging Event Log ConfigurationRemote Access Configuration MPS ConfigurationPCI Express Configuration Serial Port Mode Remote AccessRedirection After Bios Post Sredir Memory Display DelaySystem Health Monitor USB ConfigurationSystem Fan Monitor Boot SettingsFan Speed Control Modes Fan1 Speed to Fan6 SpeedsBios Settings Configuration Hard Disk Drives Boot Device PriorityRemovable Drives CD/DVD DrivesChange Supervisor Password Security SettingsChange User Password Clear User PasswordExit Options Load Optimal DefaultsSaving Changes and Exit Discarding Changes and ExitLoad Fail-Safe Defaults Appendix a Bios Error Beep Codes Amibios Error Beep CodesBeep Code Error Message Description DS7/DS8 LED Post Codes LED IndicatorsUncompressed Initialization Codes Appendix B Bios Post Checkpoint CodesBootblock Recovery Codes Uncompressed Initialization Codes Checkpoint Appendix B Bios Post Checkpoint Codes Checkpoint A9h Aah Abh B0h B1h 00h Page Appendix C Software Installation Serial ATA SataIntel 6300ESB I/O Controller Hub Configuring Sata RAID Adaptec Sata HostRAID Controller DriverAdaptec RAID Configuration Utility ARC Using the Array Configuration Utility ACU Viewing Array Properties Managing ArraysCreating Arrays Deleting ArraysPage Assigning Array Properties RAID Levels Adding a Bootable Array Deleting a Bootable Array Initializing Disk DrivesTo initialize drives Page Page To rebuild an array Rebuilding ArraysTo access the disk utilities Using the Disk UtilitiesYou can choose from the following options Exiting the Adaptec RAID Configuration UtilityInstalling the ICH5R/6300 ESBDriver Installing Additional Drivers Installing Other Software Programs and DriversSupero Doctor Supero Doctor III Interface Display Screen-II Remote Control Page Appendix D System Specifications Power Supply WeightSystem Cooling System Input Requirements