SUPER MICRO Computer 6014L-T user manual I/O Ports, Connecting the Control Panel

Page 43

Chapter 5: Advanced Serverboard Setup

Connecting the Control Panel

JF1 contains header pins for various front control panel connectors. See Figure 5-1 for the pin locations of the various front control panel buttons and LED indicators. Note that even and odd numbered pins are on opposite sides of each header.

All JF1 wires have been bundled into single ribbon cable to simplify their connection. Make sure the red wire plugs into pin 1 as marked on the board. The other end connects to the Control Panel printed circuit board, located just behind the system status LEDs in the chassis. See the Connector Deﬁ nitions section in this chapter for details and pin descriptions of JF1.

Figure 5-1. JF1 Header Pins

Ground x (key)

Power LED

HDD LED

NIC1

NIC2

OH/Fan Fail LED

Power Fail LED

Ground

Ground

5-5 I/O Ports

20 19

NMI

x (key)

Vcc

Vcc

Vcc

Vcc

Vcc

Vcc

Reset Button

Power Button

21

The I/O ports are color coded in conformance with the PC 99 speciﬁ cation. See Figure 5-2 below for the colors and locations of the various I/O ports.

Figure 5-2. I/O Ports

5-7

Image 43

Contents Super Manual Revision Release Date March 6 About This Manual PrefaceManual Organization Bios System SafetyAdvanced Serverboard Setup Advanced Chassis SetupPreface Table of Contents Advanced Serverboard Setup System SafetySMB Advanced Chassis SetupAppendices BiosPage Overview Chapter IntroductionPCI Expansion Slots Serverboard FeaturesProcessors Memory Serial ATAOnboard Controllers/Ports Other FeaturesIntel E7520 Chipset System Block Diagram Control Panel Server Chassis FeaturesSystem Power Serial ATA SubsystemRear I/O Panel Cooling SystemAsia-Paciﬁc Contacting SupermicroHeadquarters EuropePage Preparing for Setup Chapter Server InstallationUnpacking the System Rack Precautions Choosing a Setup LocationServer Precautions Rack Mounting Considerations Identifying the Sections of the Rack Rails Installing the System into a RackInstalling the Rack Rails Installing the Chassis RailsInstalling the Server into a Rack Installing the Server into the RackInstalling the Server into a Telco Rack Installing the Server into a Telco RackChecking the Serverboard Setup Accessing the Inside of the System Checking the Drive Bay Setup Control Panel Buttons Chapter System InterfaceControl Panel LEDs Serial ATA Drive Carrier LED Page Electrical Safety Precautions Chapter System SafetyGeneral Safety Precautions ESD Precautions Installing the Onboard Battery Operating PrecautionsUnpacking Chapter Advanced Serverboard SetupPrecautions Handling the ServerboardInstalling the Heatsink Brackets Serverboard InstallationInstalling the Serverboard Installing the Processors Processor and Heatsink InstallationInstalled processor Installing the HeatsinksInstalled heatsink Removing the Heatsink Connecting Data Cables Connecting CablesConnecting Power Cables I/O Ports Connecting the Control PanelDimm Installation See Figure Installing MemoryMemory Support Adding PCI Cards PCI card installationPCI slots Super X6DLP-EG2 Layout Serverboard DetailsX6DLP-EG2 Quick Reference Jumper Description Default SettingConnector Description Onboard Indicators DescriptionPower LED Connector DeﬁnitionsATX Power Connector Processor Power ConnectorNIC1/2 LEDs Power Fail LEDOverheat/Fan Fail LED Chassis Intrusion Reset ButtonPower Button JLAN1/2 Ethernet PortsUniversal Serial Bus Headers Universal Serial Bus USB0/1Fan Headers Wake-On-Ring Speaker/Power LED/KeylockWake-On-LAN ATX PS/2 Keyboard and PS/2 Mouse Ports ConnectorPower Fault SMB Power I2 CCmos Clear Jumper SettingsJLAN1/2 Enable/Disable Explanation JumpersWatch Dog VGA Enable/DisablePower Force On SMBus to PCI SlotsSystem Status LED Onboard IndicatorsAlarm Reset Jlan LEDsOnboard LED Indicators DS7, DS8 Onboard LED Indicators DS1, DS5Parallel Printer Port Header Parallel Port, Floppy, IDE and Sata Drive ConnectionsSata Connectors Floppy ConnectorIDE Drive Connectors Pin Deﬁnitions IDE1, IDE2 IDE ConnectorsTools Required Chapter Advanced Chassis SetupPrecautions Static-Sensitive DevicesChassis Front View Control PanelSystem Fan Failure Drive Bay Installation/RemovalAccessing the Drive Bays System FansMounting a Serial ATA drive in a drive carrier Serial ATA Drive InstallationInstalling/removing hot-swap Serial ATA drives Serial ATA Backplane CD-ROM and Floppy Drive InstallationPower Supply Failure Power SupplyReplacing the Power Supply Page Chapter How To Change the Conﬁguration DataIntroduction Processors Main SetupSystem Memory System Time/System Date Advanced SettingsConﬁgure Advanced CPU Settings CPU Conﬁguration Sub-MenuATA Ports Deﬁnition Combined Mode OperationIDE Conﬁguration Sub-Menu IDE ConﬁgurationA.R.T. For Hard disk drives LBA/Large ModeType Block Multi-Sector TransferPCI/PnP Conﬁguration Floppy ConﬁgurationOffboard PCI/ISA IDE Card Allocate IRQ to PCI VGAPalette Snooping PCI IDE BusMasterSuper IO Conﬁguration Sub-Menu Advanced Chipset Settings Apci Conﬁguration Power ConﬁgurationEvent Log Conﬁguration Watch Dog TimerPCI/PCI Error Logging PCI/PCI Express Error LoggingMPS Conﬁguration Remote Access ConﬁgurationPCI Express Conﬁguration Sredir Memory Display Delay Remote AccessSerial Port Mode Redirection After Bios PostSystem Health Monitor USB ConﬁgurationFan1 Speed to Fan6 Speeds Boot SettingsSystem Fan Monitor Fan Speed Control ModesBios Settings Conﬁguration CD/DVD Drives Boot Device PriorityHard Disk Drives Removable DrivesClear User Password Security SettingsChange Supervisor Password Change User PasswordDiscarding Changes and Exit Load Optimal DefaultsExit Options Saving Changes and ExitLoad Fail-Safe Defaults Amibios Error Beep Codes Appendix a Bios Error Beep CodesBeep Code Error Message Description DS7/DS8 LED Post Codes LED IndicatorsUncompressed Initialization Codes Appendix B Bios Post Checkpoint CodesBootblock Recovery Codes Uncompressed Initialization Codes Checkpoint Appendix B Bios Post Checkpoint Codes Checkpoint A9h Aah Abh B0h B1h 00h Page Serial ATA Sata Appendix C Software InstallationIntel 6300ESB I/O Controller Hub Adaptec Sata HostRAID Controller Driver Conﬁguring Sata RAIDAdaptec RAID Conﬁguration Utility ARC Using the Array Conﬁguration Utility ACU Viewing Array Properties Managing ArraysCreating Arrays Deleting ArraysPage Assigning Array Properties RAID Levels Adding a Bootable Array Initializing Disk Drives Deleting a Bootable ArrayTo initialize drives Page Page To rebuild an array Rebuilding ArraysTo access the disk utilities Using the Disk UtilitiesYou can choose from the following options Exiting the Adaptec RAID Conﬁguration UtilityInstalling the ICH5R/6300 ESBDriver Installing Additional Drivers Installing Other Software Programs and DriversSupero Doctor Supero Doctor III Interface Display Screen-II Remote Control Page Appendix D System Speciﬁcations System Input Requirements WeightPower Supply System Cooling