SUPER MICRO Computer 6014L-T Serverboard Installation, Installing the Heatsink Brackets

Page 38

SUPERSERVER 6014L-T User's Manual

5-2 Serverboard Installation

This section explains how to mount the X6DLP-EG2 into the SC811LT-260 chassis. Following the steps in the order given will eliminate the most common problems encountered in such an installation. To access the inside of the server, remove the screws from the back lip of the top cover of the chassis, then pull the cover off.

Note: Before you install the serverboard you should first attach the heatsink brackets to the back of the serverboard.

Installing the Heatsink Brackets

1.Remove the protective fi lm from the heatsink bracket.

2.Locate the heatsink bracket mounting holes on the reverse side of the serverboard.

3.Align the four pins of the heatsink bracket with the four bracket mounting holes on the back of the serverboard.

4.Insert the pins of the bracket into the corresponding mounting holes. Gently press the bracket onto the serverboard until it is fully inserted into the holes.

Installing the Serverboard

Remove the pro- tective film

Heatsink bracket mounting holes

Carefully mount the serverboard to the chassis by aligning the board holes with the raised metal standoffs that are visible on the serverboard tray. Insert screws into all the mounting holes on your serverboard that line up with the standoffs and tighten until snug (do not screw them in too tightly). Metal screws provide an electrical contact to the serverboard ground to provide a continuous ground for the system.

5-2

Image 38
Contents Super Manual Revision Release Date March 6 Manual Organization PrefaceAbout This Manual Advanced Chassis Setup System SafetyAdvanced Serverboard Setup BiosPreface Table of Contents System Safety Advanced Serverboard SetupAdvanced Chassis Setup SMBBios AppendicesPage Chapter Introduction OverviewSerial ATA Serverboard FeaturesProcessors Memory PCI Expansion SlotsOther Features Onboard Controllers/PortsIntel E7520 Chipset System Block Diagram Serial ATA Subsystem Server Chassis FeaturesSystem Power Control PanelCooling System Rear I/O PanelEurope Contacting SupermicroHeadquarters Asia-PacificPage Unpacking the System Chapter Server InstallationPreparing for Setup Server Precautions Choosing a Setup LocationRack Precautions Rack Mounting Considerations Installing the System into a Rack Identifying the Sections of the Rack RailsInstalling the Chassis Rails Installing the Rack RailsInstalling the Server into the Rack Installing the Server into a RackInstalling the Server into a Telco Rack Installing the Server into a Telco RackChecking the Serverboard Setup Accessing the Inside of the System Checking the Drive Bay Setup Chapter System Interface Control Panel ButtonsControl Panel LEDs Serial ATA Drive Carrier LED Page Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Installing the Onboard BatteryHandling the Serverboard Chapter Advanced Serverboard SetupPrecautions UnpackingInstalling the Serverboard Serverboard InstallationInstalling the Heatsink Brackets Processor and Heatsink Installation Installing the ProcessorsInstalled heatsink Installing the HeatsinksInstalled processor Removing the Heatsink Connecting Power Cables Connecting CablesConnecting Data Cables Connecting the Control Panel I/O PortsMemory Support Installing MemoryDimm Installation See Figure PCI slots PCI card installationAdding PCI Cards Serverboard Details Super X6DLP-EG2 LayoutOnboard Indicators Description Jumper Description Default SettingConnector Description X6DLP-EG2 Quick ReferenceProcessor Power Connector Connector DefinitionsATX Power Connector Power LEDOverheat/Fan Fail LED Power Fail LEDNIC1/2 LEDs JLAN1/2 Ethernet Ports Reset ButtonPower Button Chassis IntrusionFan Headers Universal Serial Bus USB0/1Universal Serial Bus Headers Wake-On-LAN Speaker/Power LED/KeylockWake-On-Ring SMB Power I2 C ConnectorPower Fault ATX PS/2 Keyboard and PS/2 Mouse PortsExplanation Jumpers Jumper SettingsJLAN1/2 Enable/Disable Cmos ClearSMBus to PCI Slots VGA Enable/DisablePower Force On Watch DogJlan LEDs Onboard IndicatorsAlarm Reset System Status LEDOnboard LED Indicators DS1, DS5 Onboard LED Indicators DS7, DS8Parallel Port, Floppy, IDE and Sata Drive Connections Parallel Printer Port HeaderFloppy Connector Sata ConnectorsIDE Connectors IDE Drive Connectors Pin Definitions IDE1, IDE2Static-Sensitive Devices Chapter Advanced Chassis SetupPrecautions Tools RequiredControl Panel Chassis Front ViewSystem Fans Drive Bay Installation/RemovalAccessing the Drive Bays System Fan FailureSerial ATA Drive Installation Mounting a Serial ATA drive in a drive carrierInstalling/removing hot-swap Serial ATA drives CD-ROM and Floppy Drive Installation Serial ATA BackplaneReplacing the Power Supply Power SupplyPower Supply Failure Page Introduction How To Change the Configuration DataChapter System Memory Main SetupProcessors CPU Configuration Sub-Menu Advanced SettingsConfigure Advanced CPU Settings System Time/System DateIDE Configuration Combined Mode OperationIDE Configuration Sub-Menu ATA Ports DefinitionBlock Multi-Sector Transfer LBA/Large ModeType A.R.T. For Hard disk drivesFloppy Configuration PCI/PnP ConfigurationPCI IDE BusMaster Allocate IRQ to PCI VGAPalette Snooping Offboard PCI/ISA IDE CardSuper IO Configuration Sub-Menu Advanced Chipset Settings Power Configuration Apci ConfigurationPCI/PCI Express Error Logging Watch Dog TimerPCI/PCI Error Logging Event Log ConfigurationPCI Express Configuration Remote Access ConfigurationMPS Configuration Redirection After Bios Post Remote AccessSerial Port Mode Sredir Memory Display DelayUSB Configuration System Health MonitorFan Speed Control Modes Boot SettingsSystem Fan Monitor Fan1 Speed to Fan6 SpeedsBios Settings Configuration Removable Drives Boot Device PriorityHard Disk Drives CD/DVD DrivesChange User Password Security SettingsChange Supervisor Password Clear User PasswordSaving Changes and Exit Load Optimal DefaultsExit Options Discarding Changes and ExitLoad Fail-Safe Defaults Beep Code Error Message Description Appendix a Bios Error Beep CodesAmibios Error Beep Codes LED Indicators DS7/DS8 LED Post CodesAppendix B Bios Post Checkpoint Codes Uncompressed Initialization CodesBootblock Recovery Codes Uncompressed Initialization Codes Checkpoint Appendix B Bios Post Checkpoint Codes Checkpoint A9h Aah Abh B0h B1h 00h Page Intel 6300ESB I/O Controller Hub Appendix C Software InstallationSerial ATA Sata Adaptec RAID Configuration Utility ARC Configuring Sata RAIDAdaptec Sata HostRAID Controller Driver Using the Array Configuration Utility ACU Managing Arrays Viewing Array PropertiesDeleting Arrays Creating ArraysPage Assigning Array Properties RAID Levels Adding a Bootable Array To initialize drives Deleting a Bootable ArrayInitializing Disk Drives Page Page Rebuilding Arrays To rebuild an arrayUsing the Disk Utilities To access the disk utilitiesExiting the Adaptec RAID Configuration Utility You can choose from the following optionsInstalling the ICH5R/6300 ESBDriver Installing Other Software Programs and Drivers Installing Additional DriversSupero Doctor Supero Doctor III Interface Display Screen-II Remote Control Page Appendix D System Specifications System Cooling WeightPower Supply System Input Requirements