SUPER MICRO Computer 6014L-T Onboard LED Indicators DS1, DS5, Onboard LED Indicators DS7, DS8

Page 57

Chapter 5: Advanced Serverboard Setup

Onboard LED Indicators (DS1, DS5)

DS1 and DS5 are additional LED indicators on the X6DLP-EG2. See the table on the right for information regarding these two LEDs.

Onboard LED Indicators (DS7, DS8)

DS7 and DS8 are POST code LEDs.

Please refer to Appendix A for POST

code information.

 

 

LED Indicators

 

 

(DS1, DS5)

 

 

 

DS#

 

Defi nition (when illuminated)

DS1

 

CPU PWR bad or processor power cable

 

 

 

not connected

DS5

 

Power present on serverboard

 

 

 

5-21

Image 57
Contents Super Manual Revision Release Date March 6 Preface About This ManualManual Organization Advanced Serverboard Setup System SafetyAdvanced Chassis Setup BiosPreface Table of Contents Advanced Serverboard Setup System SafetySMB Advanced Chassis SetupAppendices BiosPage Overview Chapter IntroductionProcessors Memory Serverboard FeaturesSerial ATA PCI Expansion SlotsOnboard Controllers/Ports Other FeaturesIntel E7520 Chipset System Block Diagram System Power Server Chassis FeaturesSerial ATA Subsystem Control PanelRear I/O Panel Cooling SystemHeadquarters Contacting SupermicroEurope Asia-PacificPage Chapter Server Installation Preparing for SetupUnpacking the System Choosing a Setup Location Rack PrecautionsServer Precautions Rack Mounting Considerations Identifying the Sections of the Rack Rails Installing the System into a RackInstalling the Rack Rails Installing the Chassis RailsInstalling the Server into a Rack Installing the Server into the RackInstalling the Server into a Telco Rack Installing the Server into a Telco RackChecking the Serverboard Setup Accessing the Inside of the System Checking the Drive Bay Setup Control Panel Buttons Chapter System InterfaceControl Panel LEDs Serial ATA Drive Carrier LED Page Electrical Safety Precautions Chapter System SafetyGeneral Safety Precautions ESD Precautions Installing the Onboard Battery Operating PrecautionsPrecautions Chapter Advanced Serverboard SetupHandling the Serverboard UnpackingServerboard Installation Installing the Heatsink BracketsInstalling the Serverboard Installing the Processors Processor and Heatsink InstallationInstalling the Heatsinks Installed processorInstalled heatsink Removing the Heatsink Connecting Cables Connecting Data CablesConnecting Power Cables I/O Ports Connecting the Control PanelInstalling Memory Dimm Installation See FigureMemory Support PCI card installation Adding PCI CardsPCI slots Super X6DLP-EG2 Layout Serverboard DetailsConnector Description Jumper Description Default SettingOnboard Indicators Description X6DLP-EG2 Quick ReferenceATX Power Connector Connector DefinitionsProcessor Power Connector Power LEDPower Fail LED NIC1/2 LEDsOverheat/Fan Fail LED Power Button Reset ButtonJLAN1/2 Ethernet Ports Chassis IntrusionUniversal Serial Bus USB0/1 Universal Serial Bus HeadersFan Headers Speaker/Power LED/Keylock Wake-On-RingWake-On-LAN Power Fault ConnectorSMB Power I2 C ATX PS/2 Keyboard and PS/2 Mouse PortsJLAN1/2 Enable/Disable Jumper SettingsExplanation Jumpers Cmos ClearPower Force On VGA Enable/DisableSMBus to PCI Slots Watch DogAlarm Reset Onboard IndicatorsJlan LEDs System Status LEDOnboard LED Indicators DS7, DS8 Onboard LED Indicators DS1, DS5Parallel Printer Port Header Parallel Port, Floppy, IDE and Sata Drive ConnectionsSata Connectors Floppy ConnectorIDE Drive Connectors Pin Definitions IDE1, IDE2 IDE ConnectorsPrecautions Chapter Advanced Chassis SetupStatic-Sensitive Devices Tools RequiredChassis Front View Control PanelAccessing the Drive Bays Drive Bay Installation/RemovalSystem Fans System Fan FailureMounting a Serial ATA drive in a drive carrier Serial ATA Drive InstallationInstalling/removing hot-swap Serial ATA drives Serial ATA Backplane CD-ROM and Floppy Drive InstallationPower Supply Power Supply FailureReplacing the Power Supply Page How To Change the Configuration Data ChapterIntroduction Main Setup ProcessorsSystem Memory Configure Advanced CPU Settings Advanced SettingsCPU Configuration Sub-Menu System Time/System DateIDE Configuration Sub-Menu Combined Mode OperationIDE Configuration ATA Ports DefinitionType LBA/Large ModeBlock Multi-Sector Transfer A.R.T. For Hard disk drivesPCI/PnP Configuration Floppy ConfigurationPalette Snooping Allocate IRQ to PCI VGAPCI IDE BusMaster Offboard PCI/ISA IDE CardSuper IO Configuration Sub-Menu Advanced Chipset Settings Apci Configuration Power ConfigurationPCI/PCI Error Logging Watch Dog TimerPCI/PCI Express Error Logging Event Log ConfigurationRemote Access Configuration MPS ConfigurationPCI Express Configuration Serial Port Mode Remote AccessRedirection After Bios Post Sredir Memory Display DelaySystem Health Monitor USB ConfigurationSystem Fan Monitor Boot SettingsFan Speed Control Modes Fan1 Speed to Fan6 SpeedsBios Settings Configuration Hard Disk Drives Boot Device PriorityRemovable Drives CD/DVD DrivesChange Supervisor Password Security SettingsChange User Password Clear User PasswordExit Options Load Optimal DefaultsSaving Changes and Exit Discarding Changes and ExitLoad Fail-Safe Defaults Appendix a Bios Error Beep Codes Amibios Error Beep CodesBeep Code Error Message Description DS7/DS8 LED Post Codes LED IndicatorsUncompressed Initialization Codes Appendix B Bios Post Checkpoint CodesBootblock Recovery Codes Uncompressed Initialization Codes Checkpoint Appendix B Bios Post Checkpoint Codes Checkpoint A9h Aah Abh B0h B1h 00h Page Appendix C Software Installation Serial ATA SataIntel 6300ESB I/O Controller Hub Configuring Sata RAID Adaptec Sata HostRAID Controller DriverAdaptec RAID Configuration Utility ARC Using the Array Configuration Utility ACU Viewing Array Properties Managing ArraysCreating Arrays Deleting ArraysPage Assigning Array Properties RAID Levels Adding a Bootable Array Deleting a Bootable Array Initializing Disk DrivesTo initialize drives Page Page To rebuild an array Rebuilding ArraysTo access the disk utilities Using the Disk UtilitiesYou can choose from the following options Exiting the Adaptec RAID Configuration UtilityInstalling the ICH5R/6300 ESBDriver Installing Additional Drivers Installing Other Software Programs and DriversSupero Doctor Supero Doctor III Interface Display Screen-II Remote Control Page Appendix D System Specifications Power Supply WeightSystem Cooling System Input Requirements